oil dipstick SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Full level mark (hole)
2. Low level mark (hole)
0B-10 MAINTENANCE AND LUBRICATION
NOTE:
Engine oil capacity is specified. However, note that the
amount of oil required when actually changing oil may
somewhat differ from the data in the table depending on
various conditions (temperature, viscosity, etc.).
7) Check oil filter and drain plug for oil leakage.
8) Start engine and run it for three minutes. Stop it and wait five min-
utes before checking oil level. Add oil, as necessary, to bring oil
level to FULL level mark on dipstick.
NOTE:
Step 1) ± 7) outlined above must be performed with ENGINE
NOT RUNNING. For step 8), be sure to have adequate ven-
tilation while engine is running.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
1) Remove radiator cap when engine is cool.
2) Loosen radiator drain plug to drain coolant.
3) Remove reservoir, which is on the side of radiator, and drain.
4) Tighten plug securely. Also reinstall reservoir.
5) Fill radiator with specified amount of coolant, and run engine for
2 or 3 minutes at idle. This drives out any air which may still be
trapped within cooling system. STOP ENGINE. Add coolant as
necessary until coolant level reaches the filler throat of radiator.
Reinstall radiator cap.

YH4
GRAND
VITARA
1. Fluid pressure check hole
2. Oil pan
1. Oil pan
2. Exhaust pipe
7B1-54 AUTOMATIC TRANSMISSION (4 A / T)
LINE PRESSURE TEST
Purpose of this test is to check operating conditions of each part by
measuring fluid pressure in fluid pressure line. Line pressure test
requires following conditions.

Automatic fluid is at normal operating temperature (70 to 80C /
158 ± 176F).

Fluid is filled to proper level (between FULL HOT and LOW HOT
on dipstick).
1) Apply parking brake securely and place checks against wheels.
2) Attach oil pressure gauge to fluid pressure check hole in trans-
mission case.
Special Tool
(A): 09925-37810
CAUTION:
After attaching oil pressure gauge, check that not fluid
leakage exists.
3) Depress foot brake fully, run engine at idle and stall and then
check fluid pressure in ªDº or ªRº range.
CAUTION:
Do not continue running engine at stall speed longer than
5 seconds.
G16 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
5.1 ± 5.7 kg / cm2
73 ± 81 psi
At stall speed11.7 ± 13.2 kg / cm2
166 ± 188 psi
14.2 ± 16.7 kg / cm2
202 ± 237 psi
J20 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.8 ± 4.3 kg / cm2
54 ± 61 psi
5.3 ± 5.9 kg / cm2
75 ± 84 psi
At stall speed9.7 ± 11.2 kg / cm2
138 ± 159 psi
12.9 ± 15.5 kg / cm2
183 ± 220 psi
H25 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
6.6 ± 7.2 kg / cm2
94 ± 102 psi
At stall speed11.3 ± 12.7 kg / cm2
161 ± 181 psi
14.7 ± 22.7 kg / cm2
209 ± 323 psi

YH4
GRAND
VITARA
1. Dipstick (G16 / J20)
2. Dipstick (H25)
1. Drain plug
2. Propeller shaft
1. Dipstick (G16 / J20)
2. Dipstick (H25)
7B1-60 AUTOMATIC TRANSMISSION (4 A / T)
LEVEL CHECK AT ROOM TEMPERATURE
The fluid level check at room temperature performed after repair or
fluid change before test driving is just preparation for level check of
normal operating temperature. The checking procedure itself is the
same as that described previously. If the fluid level is between FULL
COLD and LOW COLD, proceed to test drive. And when the fluid
temperature has reached the normal operating temperature, check
fluid level again and adjust it as necessary.
FLUID CHANGE
1) Lift up vehicle.
2) With engine is cool, remove drain plug from oil pan and drain A / T
fluid.
3) Install drain plug.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Lower vehicle and fill proper amount of an equivalent of DEX-
RON
-III.
5) Check fluid level according to procedure described under LEV-
EL CHECK NORMAL OPERATING TEMPERATURE.
Fluid specification
An equivalent of DEXRON
-III
Fluid capacity
When draining
from drain plug
hole
2.5 liters (5.28/4.40 US/lmp.pt.)
When
overhauling
6.9 liters (14.58/12.14 US/lmp.pt.)
for G16
7.1 liters (15.00/12.50 US/lmp.pt.)
for J20 / H25

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-65
1. Drain plug
2. Propeller shaft
1. Oiler (with transmission fluid)
2. Solenoid valve
3. BatteryA: Hole (Should be dry)
B: Exhausting fluid Terminal Arrangement of PCM Coupler
(Viewed from harness side)
WITH BATTERY VOLTAGE WITHOUT BATTERY VOLTAGE
H25 Engine
Shift solenoid valve ± A (#1)C51-1-6
Shift solenoid valve ± B (#2)C51-1-1
TCC (Lock-up) solenoid valveC51-1-2
REMOVAL
1) Pull out dipstick and lift up vehicle.
2) With engine cooled, remove drain plug from oil pan and drain
A / T fluid.
3) Install drain plug with gasket.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Remove exhaust pipe bracket and disconnect front propeller
shaft from front differential (if equipped).
5) Remove oil pan bolts.
6) Remove oil pan.
7) Remove oil tubes.
8) Remove solenoid valve No.1 (shift solenoid valve A and B) or so-
lenoid valve No.2 (TCC solenoid valve).
OPERATION CHECK
Whenever shift solenoid valves and TCC (lock-up) solenoid valve
are removed from transmission, verify their valve function physical-
ly before they are reinstalled.
1) Apply oiler to solenoid valve and give compression by hands
and then check to be sure that transmission fluid from oiler does
not come out of holes in solenoid valve when battery voltage is
not conducted.
2) Under the same conditions as above, conduct battery voltage
and then make sure that fluid comes out with vigor.
NOTE:

If fluid does not come out with vigor in above step 2 in-
spection, do not re-use that solenoid valve.

Figure at the left shows shift solenoid valve check.
Check TCC solenoid valve also in the same way.

YH4
GRAND
VITARA
7B1-74 AUTOMATIC TRANSMISSION (4 A / T)
1. Boot No.2
2. Boot cover
1. Boot clamp
2. Boot No.1
3. Gear shift control lever
1. Boot No.2
2. Transfer shift control
lever
3. Transfer shift lever case4. Transfer shift control
case cover
5. Boot No.1
1. A / T throttle cable
2. Adjusting nut
3. Lock nut
G16 / J20 H25
DISMOUNTING OF TRANSMISSION (WITH
TRANSFER IF EQUIPPED)
IN CABIN
1) Remove console box.
NOTE:
To remove clip, push in its center pin first.
2) Remove boot cover and boot No.2. (if equipped)
3) Remove boot clamp and then remove boot No.1 from transfer
gear shift lever case. (if equipped)
4) With transfer shift control case cover pushed down with fingers,
turn it to counterclockwise and take out shift control lever. (if
equipped)
IN ENGINE ROOM
1) Remove battery, dipstick and oil filler tube.
2) Disconnect A
/
T throttle cable from throttle cam and bracket.
3) Remove starter motor. But don't disconnect its wiring harness.
4) Remove transmission to engine bolt and nut.