Adjust SUZUKI GRAND VITARA 2003 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Seat cushion
2. Seat back
3. Reclining assy (RH side)
4. Reclining assy (LH side)
5. Seat adjuster (RH outside)
6. Seat adjuster (RH inside)
7. Seat adjuster (LH outside)
8. Seat adjuster (LH inside)
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
(b): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Cover
2. Coupler(b)
9-34 BODY SERVICE
SEAT
FRONT SEAT
REMOVAL
1) Disconnect lead wire(s) at coupler (if equipped). Remove four
mounting bolts fixing front seat to seat rail to remove front seat.
2) Disassemble and repair seat as necessary.
INSTALLATION
Reverse removal procedure to install front seat.
Torque to specifications, as shown.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)

YH4
GRAND
VITARA
9-60 BODY SERVICE
1. Door latch
2. Door latch striker
3. Shaft
1. Door latch striker
2. Body
3. Door4. Front side
5. Shim
INSTALLATION
To install front door lock, reverse removal procedure, noting follow-
ing.

Door latch striker.
Move door latch striker up or down so its center aligns with the
center of groove ªAº on the door, as shown.
NOTE:
Striker should be moved vertically and placed level. Do not
adjust door lock.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)

Move door latch striker sideways to adjust door surface flush with
body surface, as shown.
In order to correctly obtain door latch striker position in the fore-
and-aft direction, increase or decrease number of shims inserted
between body and striker to adjust it.
Dimension ªaº: 10.9 ± 12.9 mm (0.43 ± 0.5 in.)
ªbº: 3.4 ± 5.4 mm (0.13 ± 0.21 in.)
NOTE:
Apply oil or grease to striker joints periodically.

YH4
GRAND
VITARA
1. Shim
1. Rubber cushion 1
9-62 BODY SERVICE
BACK DOOR / REAR GATE LOCK ASSEMBLY
REMOVAL
1) Remove inside handle bezel (if equipped).
2) Remove inside lock knob.
3) Remove door trim.
With inside handle bezel tilted as shown in figure, turn door trim
90 counterclockwise to remove it (if equipped with inside han-
dle).
4) Remove back door / rear gate sealing cover.
5) Remove back door / rear gate lock control rod.
Unlock back door / rear gate lock rod pin retainer and disconnect
control rod.
6) Disconnect back door lock motor lead wire (if equipped).
7) Remove lock assembly.
INSTALLATION
Reverse removal procedure to install back door / rear gate lock as-
sembly noting following points.

Back door / Rear gate latch striker.
Adjust back door / rear gate latch striker so that its center aligns
with the center of groove in back door / rear gate latch base.
To adjust back door / rear gate latch and striker with each other,
insert proper number of shims below the bottom of striker, as
shown.

Back door / Rear gate rubber cushion.
Move rubber cushion installed at the left side of back door / rear
gate to align it with its guide.

YH4
GRAND
VITARA
BODY SERVICE 9-65
Section A ± A
ADJUSTMENT
1) Loosen sunroof glass fixing screws (at 4 locations) and move
sunroof glass up and down 2 to 3 times. In this way, sunroof
glass can be positioned in both vertical and horizontal directions
by elasticity of sliding roof weather strip.
2) Position sunroof glass by such dimensions with respect to roof
panel surface as specified below.
Dimension: ªaº: 0 mm (0.0 in.)
3) After installing all parts and adjusting properly, check sunroof for
proper operation (open, close and up).
SLIDING ROOF DEFLECTOR
REMOVAL
1) Open sliding roof.
2) Disconnect negative cable at battery.
3) Remove screws and disconnect deflector from deflector link.
INSTALLATION
Reverse removal procedure to install deflector.

YH4
GRAND
VITARA
9-70 BODY SERVICE
1. Pin on body side
2. Sliding roof
1. Drain hose
INSTALLATION
For installation, reverse removal procedure, noting following
points.

Align positioning holes in sliding roof assembly at right and left
and pins on body side for installation.

Connect drain hoses to sliding roof assembly at 4 locations. Pass
front drain hose between roof panel and inner panel and through
front pillar down to sill side. Pass rear drain hose into baring hole
in rear quarter inner panel and through C pillar down to jig hole
in rear side bumper.
NOTE:
After reinstalling sliding roof assembly, be sure to make
glass adjustment. (Refer to SLIDING ROOF GLASS ADJUST-
MENT described previously.)