engine control SUZUKI GRAND VITARA 2003 2.G Service Owner's Manual

YH4
GRAND
VITARA
7A-14 MANUAL TRANSMISSION (TYPE 1)
09951-16060
Oil seal installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back up light switch (Type 1)202.014.5
Back up light switch (Type 2)454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts and nut505.036.5
Exhaust center pipe to manifold nuts505.036.5
Muffler to exhaust center pipe bolts505.036.5
Universal joint flange bolts505.036.5
Select return spring bolts232.317.0
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever.

Select return springs, bolts and guides.
Thread lock cementTHREAD LOCK CEMENT
SUPER 1333B (99000-32020)
Shift control lever locating bolts.
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil Drain and filler / level plugs.
SPECIAL TOOL

YH4
GRAND
VITARA
7A1
MANUAL TRANSMISSION (TYPE 2) 7A1-1
TYPE 2
GENERAL DESCRIPTION7A1-1 . . . . . . . . . . . . . .
DIAGNOSIS7A1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A1-3 . . . . . . . . . . . . . . . .
Gear Oil 7A1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A1-4. . . . . . . . . . . . . . . . . . .
Switches 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A1-4. . . . . . . . . . . . . . . . Dismounting / Remounting of
Trans. Unit 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A1-4 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A1-5 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A1-5 . . . . . .
The manual transmission consists of the input shaft,
main shaft, counter shaft and reverse gear which are
installed in the aluminum and castings cases. Its
gears are of forward five speeds in synchro mesh and
reverse one speed in sliding idler gear arrangement
system.
The main shaft gears are held by the needle bear-
ings and on them the synchronizer rings and syn-
chronizer sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.As the aluminum and castings cases are sealed with
liquid type gasket, it is necessary to use genuine seal-
ant or its equivalent on its mating surfaces when reas-
sembling them. Also, the case fastening bolts must be
tightened to specified torque by means of the torque
wrench and tightening over or below the specified
torque should be avoided.
The description under ON-VEHICLE SERVICE in this
section covers the transfer partially which is next to
the transmission as well, but their gear boxes are in-
dependent and each of them has its own drain and
level / filler plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A1
MANUAL TRANSMISSION
(TYPE 2)
CONTENTS
GENERAL DESCRIPTION

YH4
GRAND
VITARA
Viscosity chart
SAE
Temperature
1. Drain plug
2. Oil level / filler plug
MANUAL TRANSMISSION (TYPE 2) 7A1-3
ON-VEHICLE SERVICE
GEAR OIL
INSPECTION AND CHANGE
1) Before changing or inspecting oil, be sure to stop engine and lift
vehicle horizontally.
2) With vehicle lifted up, check oil level and leakage. If leakage ex-
ists, correct or repair it.
3) Drain old oil and fill new specified oil as shown below by speci-
fied amount (roughly up to level hole).
NOTE:

It is highly recommended to use SAE 75W-90 gear oil.

Whenever vehicle is hoisted for any other service work
than oil change, also be sure to check for oil leakage and
status of breather hoses.

If water or rust is mixed in drained oil, be sure to check
breather hose and boot of transmission and transfer.
Gear Oil Specification
Oil grade: API GL-4
Viscosity: SAE 75W-85, 75W-90 or 80W-90
Oil Capacity:
Transmission 2.6 liters (5.5 / 4.6 US / Imp. pt)
Transfer 1.7 liters (3.6 / 3.0 US / Imp. pt)
4) Torque drain plug and level / filler plug as specified below after
applying sealant to thread of plug (c).
CAUTION:
Transmission oil must not be poured through gear shift
control lever part.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 38 N´m (3.8 kg-m, 27.5 lb-ft)
(b): 23 N´m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
7A1-4 MANUAL TRANSMISSION (TYPE 2)
SHIFT CONTROL LEVERS
Refer to SECTION 7A in this manual.
SWITCHES
Refer to SECTION 7A in this manual.
ENGINE REAR MOUNTING
Refer to SECTION 7A in this manual.
DISMOUNTING / REMOUNTING OF TRANS.
UNIT
Refer to the same item in SECTION 7A ªMANUAL TRANSMIS-
SIONº.
For tightening torque of filler and level / drain plug, refer to ªGear Oil
Inspection and Changeº of ªON-VEHICLE SERVICEº in this sec-
tion.
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.

YH4
GRAND
VITARA
MANUAL TRANSMISSION (TYPE 2) 7A1-5
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN´mkg-mlb-ft
Transfer oil filler / level and drain plugs232.317.0
Transmission oil filler / level and drain plugs383.827.5
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back-up light switch454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts505.036.5
Muffler to exhaust No. 2 pipe nuts505.036.5
Universal joint flange bolts505.036.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever
Thread lock cement
THREAD LOCK CEMENT
SUPER 1333B
(99000-32020)

Shift control lever locating bolts
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil drain and filler / level plugs

YH4
GRAND
VITARA
7B1-2 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0753 Shift Solenoid-A (#1)
Electrical 7B1-50. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0758 Shift Solenoid-B (#2)
Electrical 7B1-50. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1875 4WD Low Switch Circuit
Malfunction 7B1-52. . . . . . . . . . . . . . . . . . . . . . .
Line Pressure Test 7B1-54. . . . . . . . . . . . . . . . . .
Stall Test 7B1-55. . . . . . . . . . . . . . . . . . . . . . . . . .
Road Test 7B1-56. . . . . . . . . . . . . . . . . . . . . . . . .
Manual Road Test 7B1-57. . . . . . . . . . . . . . . . . .
Time Lag Test 7B1-57. . . . . . . . . . . . . . . . . . . . . .
Engine Brake Test 7B1-58. . . . . . . . . . . . . . . . . .
ªPº Range Test 7B1-58. . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7B1-59 . . . . . . . . . . . . . . . .
MAINTENANCE SERVICE 7B1-59. . . . . . . . . . . .
Fluid Level 7B1-59. . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Change 7B1-60. . . . . . . . . . . . . . . . . . . . . .
Oil Cooler Hoses 7B1-61. . . . . . . . . . . . . . . . . . .
A / T THROTTLE CABLE 7B1-61. . . . . . . . . . . . . . .
MANUAL SELECTOR ASSEMBLY 7B1-62. . . . .
SELECT CABLE 7B1-63. . . . . . . . . . . . . . . . . . . . . TRANSMISSION RANGE SWITCH 7B1-64. . . . .
A
/
T OUTPUT SPEED SENSOR 7B1-64. . . . . . . .
O / D CUT SWITCH 7B1-64. . . . . . . . . . . . . . . . . . .
SOLENOID VALVES 7B1-64. . . . . . . . . . . . . . . . . .
THROTTLE POSITION SENSOR 7B1-66. . . . . . .
POWER / NORMAL CHANGE SWITCH 7B1-66. .
OIL COOLER PIPES 7B1-67. . . . . . . . . . . . . . . . . .
BRAKE INTERLOCK SYSTEM 7B1-68. . . . . . . . .
Shift Lock Solenoid Control 7B1-68. . . . . . . . . .
Shift Lock Solenoid Control Operations 7B1-68
Shift Lock (Solenoid) Manual Release 7B1-69.
System Inspection 7B1-69. . . . . . . . . . . . . . . . . .
KEY INTERLOCK CABLE 7B1-71. . . . . . . . . . . . .
DISMOUNTING OF TRANSMISSION
(WITH TRANSFER IF EQUIPPED) 7B1-74. . . .
REMOUNTING 7B1-77. . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7B1-78 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7B1-78 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7B1-79 . . . . . .
SPECIAL TOOLS7B1-79 . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
7B1-4 AUTOMATIC TRANSMISSION (4 A / T)
ItemSpecifications
Torque
conver-
terType
Stall torque ratio3-element, 1-step, 2-phase type (with TCC (lock-up)
mechanism)
2.4 (G16 engine) 2.0 (J20 engine) 1.9 (H25 engine)
Oil
pumpType
Drive systemTrochoid type oil pump
Engine driven
TypeForward 4-step, reverse 1-step planetary gear type
Shift position
ªPº range Gear in neutral, output shaft fixed,engine start
ªRº range Reverse
ªNº range Gear in neutral, engine start
ªDº range Forward 1st
2nd
3rd
4th (O / D)
(O / D ON) automatic gear change
ªDº range Forward 1st
2nd
3rd
(O / D OFF) automatic gear change
ª2º range (Normal mode) Forward 1st
2nd  3rd automatic gear
change
(Power mode) Forward 2nd  3rd automatic gear
change and fixed at 2nd gear
ªLº range Forward 1st  2nd  3rd reduction, and fixed at 1st gear
GearEngine typeG16 engineJ20 / H25 engines
change
device1st (low gear)2.8262.826device2nd (second gear)1.4931.493
Gear3rd (top gear)1.0001.000Gear
ratio4th (overdrive
4th gear)0.7300.689
Reverse (reverse
Reverse gear)2.7032.703
Control elements
Wet type multi-disc clutch 3 sets. . . . . . . . . .
Wet type multi-disc brake 4 sets. . . . . . . . . .
One-way clutch 3 sets. . . . . . . . . . . . . . . . . . .
TransferHi: 1.000 Lo: 1.816 (4WD model only)
Final gear reduction
ratio (Differential)5.125 (G16 engine) 4.875 (J20 / H25 engines)
Lubrica-
tionLubrication systemForce feed system by oil pump
CoolingCooling systemRadiator assisted cooling (water-cooled)
Fluid usedAn equivalent of DEXRON
III

YH4
GRAND
VITARA
Engine
Vehicle speed
sensor
Throttle position
sensor
ECT sensor
Cruise control
module
(if equipped)Torque converter Planetary gear
Final gear
reduction unit
Oil pump
Shift and TCC
solenoid valvesClutch and brake
Control valve
ªO / D OFFº lamp
ªPOWERº lamp
MILTransmission range
switch
O / D cut switch
P / N change switch
Transfer 4L switch
(if equipped)
CMP sensor Powertrain (engine) control module
Power transmission
Fluid pressure circuit
Electric signalInput speed sensor Brake pedal switch
Output speed sensor
AUTOMATIC TRANSMISSION (4 A / T) 7B1-7
ELECTRONIC SHIFT CONTROL SYSTEM
The gear ratio change in ªDº or ª2º range and torque converter clutch operation are controlled by Powertrain (En-
gine) Control Module.

YH4
GRAND
VITARA
7B1-8 AUTOMATIC TRANSMISSION (4 A / T)
G16 / J20 Engines
1. PCM (ECM)
2. VSS
3. CMP sensor
4. TP sensor
5. ECT sensor
6. A / T input speed sensor
7. A / T output speed sensor
8. Transmission range switch9. Shift solenoid-A
10. Shift solenoid-B
11. TCC solenoid
12. Data link connector
13. Cruise control module
14. ªPOWERº lamp
15. ªO / D OFFº lamp
16. MIL17. O / D cut switch
18. P / N change switch
19. 4WD low switch
20. Main relay
21. Ignition switch
22. Battery
23. PCM (ECM) connector terminal
(viewed from harness side) Bl / Y
Bl / G
W
OrC51-1-11
C51-1-10
C51-1-23
C51-1-22
12V

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-9
H25 Engine
1. PCM (ECM)
2. VSS
3. CMP sensor
4. TP sensor
5. ECT sensor
6. Brake pedal switch
7. A / T input speed sensor
8. A / T output speed sensor9. Transmission range switch
10. Shift solenoid-A
11. Shift solenoid-B
12. TCC solenoid
13. Data link connector
14. Cruise control module
15. ªPOWERº lamp
16. ªO / D OFFº lamp17. MIL
18. O / D cut switch
19. P / N change switch
20. 4WD low switch
21. Main relay
22. Ignition switch
23. Battery
24. PCM (ECM) connector terminal
(viewed from harness side) Bl / Y
Bl / G
W
OrC51-1-16
C51-1-8
C51-1-10
C51-1-9
12V