Rear brake SUZUKI GRAND VITARA 2003 2.G Service Manual PDF
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2003, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2003 2.GPages: 801, PDF Size: 12.15 MB
Page 425 of 801
YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-23
User name: Model: VIN:
Date of issue: Date of Reg: Date of problem: Mileage:
PROBLEM SYMPTOMS
Engine does not start
Vehicle does not move
(forward, rearward)
No lock-up (TCC clutch operation)
Shift point too high or too low
Excessive gear change shockEngine stops
Transmission does not shift
(1st, 2nd, 3rd, 4th, Rev) gear
Automatic shift does not occur
Transmission slipping in
(1st, 2nd, 3rd, 4th, Rev) gear
Other:
VEHICLE/ ENVIRONMENTAL CONDITION WHEN PROBLEM OCCURS
Environmental Condition
Weather
Temperature
Frequency
RoadFair/Cloudy/Rain/Snow/Always/Other ( )
Hot/Warm/Cool/Cold/(CF)/Always
Always/Sometimes/( times/ day, month)/Only Once
Urban/Suburb/Highway/Mountainous (uphill/downhill)/Paved road/Gravel/
Other( )
Vehicle Condition
Engine
Brake
O/D cut switch
P/N change switch
(P,R,N,D,2,L) range/( ) range
Cold/Warming up phase/Warmed up
At stop/During driving (constant speed/accelerating/decelerating/
right hand corner/left hand corner)/Other ( )/Speed ( km/h mile/h)
Speed( r/min)/Throttle opening(idle/about %/full)
Apply/Not apply
ON/OFF
Power/Normal
Malfunction indicator lamp condition
Always ON Sometimes ON Always OFF Good condition
Diagnostic trouble
codeFirst check : No codeMalfunction code( )
Second check : No code Malfunction code( )
Transmission range
Transmission temp.
Vehicle
CUSTOMER PROBLEM INSPECTION FORM (EXAMPLE)
NOTE:
The above form is a standard sample. It should be modified according to conditions characteristic of each
market.
Page 459 of 801
YH4
GRAND
VITARA
1
1. Shift solenoids connector
AUTOMATIC TRANSMISSION (4 A / T) 7B1-57
MANUAL ROAD TEST
This test check the gear being used in ªLº, ª2º or ªDº range when
driven with unoperated gear shift control system. Test drive vehicle
on a level road.
NOTE:
Before this test, check diagnostic trouble code (DTC).
1) Disconnect coupler of shift solenoid valves on transmission.
WARNING:
To avoid the danger of being burned, do not touch the hot
exhaust system when disconnecting shift solenoid
valves coupler.
2) With select lever in ªPº, start engine and warm it up.
3) With select lever in ªLº range, start vehicle and accelerate to 20
km/h (12.5 mile/h). Check in this state that 1st gear is being
used.
4) At 20 km/h (12.5 mile/h), shift select lever to 2 range and acceler-
ate to 40 km/h (25 mile/h). Check in this state that 3rd gear is
being used.
5) At 40 km/h (25 mile/h), shift select lever to D range and check
that O/D gear is used when speed is higher than 40 km/h (25
mile/h).
6) After above checks, stop vehicle then engine, and connect shift
solenoids coupler with ignition switch OFF.
WARNING:
To avoid the danger of being burned, do not touch the hot
exhaust system when connecting shift solenoid valves
coupler.
7) Clear DTC with scan tool.
TIME LAG TEST
This test is to check conditions of clutch, reverse brake and fluid
pressure. ªTime lagº means time elapsed since select lever is
shifted with engine idling till shock is felt.
1) With chocks placed before and behind front and rear wheels re-
spectively, depress brake pedal.
2) Start engine.
3) With stop watch ready, shift select lever from ªNº to ªDº range
and measure time from that moment till shock is felt.
4) Similarly measure time lag by shifting select lever from ªNº to ªRº
range.
Specification for ªNºªDºLess than 1.2 sec.
time lagªNºªRºLess than 1.5 sec.
NOTE:
When repeating this test, be sure to wait at least minute
after select lever is shifted back to ªNº range.
Engine should be warmed up fully for this test.
Test resultPossible causes
When ªNºªDº time lag
exceeds specificationLow line pressure
Worn forward clutch
When ªNºªRº time lag
exceeds specificationLow line pressure
Worn direct clutch
Worn reverse brake
Page 460 of 801
YH4
GRAND
VITARA
7B1-58 AUTOMATIC TRANSMISSION (4 A / T)
ENGINE BRAKE TEST
WARNING:
Before test, make sure that there is no vehicle behind so as
to prevent rear-end collision.
1) While driving vehicle in 3rd gear of ªDº range, shift select lever
down to ª2º range and check if engine brake operates.
2) In the same way as in step 1, check engine brake for operation
when select lever is shifted down to ªLº range.
3) If engine brake fails to operate in above tests, possible causes
for such failure are as follows. Check each part which is sus-
pected to be the cause.
Condition
Possible cause
Fails to operate when shifted
down to ª2º rangeSecond coast brake defec-
tive
Fails to operate when shifted
down to ªLº rangeReverse brake defective
ªPº RANGE TEST
1) Stop vehicle on a slope, shift select lever to ªPº range and at the
same time apply parking brake.
2) After stopping engine, depress brake pedal and release parking
brake.
3) Then, release brake pedal gradually and check that vehicle re-
mains stationary.
4) Depress brake pedal and shift select lever to ªNº range.
5) Then, release brake pedal gradually and check that vehicle
moves.
WARNING:
Before test, check to make sure no one is around vehicle
or down on a slope and keep watchful for safety during
test.
Page 471 of 801
YH4
GRAND
VITARA
Type-2
1. Select lever
2. Detent pin
3. Detent plate4. Lock plate
5. Shift lock solenoid
1. Cover
2. Screw3. Select lever
4. Button
AUTOMATIC TRANSMISSION (4 A / T) 7B1-69
SHIFT LOCK (SOLENOID) MANUAL RELEASE
Shift lock can be manually released by following procedure.
1) Remove access hole cover by unfastening screw.
2) Turn ignition key to ªACCº position and move shift lock solenoid
rod (or manual release plate) toward rear side of vehicle by using
screw driver or the like.
3) In this state, select lever can be moved to any range or position.
SYSTEM INSPECTION
1) Check to make sure that select lever cannot be moved to any
other range from ªPº range position when ignition switch key is
at ªACCº position, at ªLOCKº position (or it is removed from key-
hole of ignition switch) or brake pedal is not depressed.
2) Shift select lever to ªPº range position, release knob button and
check for the following.
Ignition key can be turned between ªLOCKº and ªACCº posi-
tions back and forth and also it can be removed from ignition
switch.
Page 523 of 801
YH4
GRAND
VITARA
1. Match mark
1. Differential to rear axle nut
7F-4 DIFFERENTIAL (REAR)
DISMOUNTING
1) Lift up vehicle and drain oil from rear differential housing.
2) Remove rear brake drums and pull out right and left rear axle
shafts. (Refer to rear axle shaft removal of SECTION 3E.)
3) Before removing propeller shaft, give match marks on joint
flange and propeller shaft as shown.
4) Remove propeller shaft by removing its 4 flange bolts and nuts.
5) Remove differential assembly by removing its 8 fastening nuts.
Page 524 of 801
YH4
GRAND
VITARA
1. Differential to rear axle nut
(a)
(a)
DIFFERENTIAL (REAR) 7F-5
REMOUNTING
1) Clean mating surfaces of rear axle and differential assembly and
apply sealant (Suzuki bond 1215) to axle side evenly.
ªAº: Sealant 99000-31110
2) Install differential assembly to axle and fix it with nuts tightened
to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
3) Install propeller shaft to joint flange aligning match marks and
torque flange bolts to specification.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
4) Install right and left rear axle shafts and drums.
(Refer to rear axle installation of SECTION 3E and rear brake
drum installation of SECTION 5.)
5) Install wheels.
6) Fill hypoid gear oil as specified and tighten plug to specification.
Lower lift.
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in Foreword of this manual.
Page 532 of 801
YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 536 of 801
YH4
GRAND
VITARA
LIGHTING SYSTEM 8B-5
CLEARANCE, TAIL AND LICENCE PLATE LIGHTS
TroublePossible causeCorrection
All lights do not lightªTAILº fuse blown
Lighting switch faulty
Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
Some lights do not light
upBulb(s) blown
Wiring or grounding faultyReplace bulb(s)
Repair
BACK-UP LIGHTS
TroublePossible causeCorrection
Back-up lights do not
lightªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)
Bulb blown
switch faulty
Wiring or grounding faultyReplace fuse to check for short
Replace bulb
Replace switch
Repair
Back-up lights remains
ONBack-up light switch or shift switch faulty
Wiring or grounding faultyReplace switch
Repair
BRAKE LIGHTS
TroublePossible causeCorrection
Brake lights do not light
upªSTOP / HORNº fuse blown (Hard Top
Model)
ªSTPº fuse blown (Canvas Top Model)
Bulb(s) blown
Brake light switch faulty
Wiring or grounding faultyReplace fuse to check for short
Replace bulb(s)
Adjust or replace switch
Repair
Brake lights stay onBrake light switch faultyAdjust or replace switch
Only one light does not
lightBulb blown
Wiring or grounding faultyReplace bulb
Repair
REAR FOG LIGHT (IF EQUIPPED)
TroublePossible causeCorrection
Rear fog light does not
come onªFOGº fuse blown
Rear fog light switch faulty
Lighting switch faulty
Wiring or grounding faulty
Bulb blownReplace fuse to check for short
Replace fog light switch
Replace switch
Repair
Replace bulb
INTERIOR LIGHTS
TroublePossible causeCorrection
Interior light (s) does (do)
not light upBulb(s) blown
ªDOMEº fuse blown (Hard Top Model)
ªDOMº fuse blown (Canvas Top Model)
Wiring or grounding faulty
Door switch faulty
Interior light switch faultyReplace bulb(s)
Replace fuse to check for short
Repair
Replace switch
Replace light assy
Front spot lights do not
light upBulb(s) blown
Wiring or grounding faulty
Spot light switch faultyReplace bulb(s)
Repair
Replace light assy
Page 690 of 801
YH4
GRAND
VITARA
9-72 BODY SERVICE
1. Front floor carpet
2. Luggage floor carpet
3. Dash panel insulation
1. Dash side trim
2. Front side sill scuffs
3. Center pillar inner lower trim
4. Rear side sill scuff5. Fastener
6. Side sill scuff
7. Rear quarter lower trim
EXTERIOR AND INTERIOR TRIM
FLOOR CARPET
FRONT FLOOR CARPET
REMOVAL
1) Remove front seats and rear seat cushions.
2) Remove seat belt lower anchor bolt.
3) Remove dash side trims, front side sill scuffs (4 door model),
center pillar inner lower rims (4 door model), rear side sill scuffs
(4 door model), side sill scuffs (2 door model) and rear quarter
lower trim.
4) Remove parking brake lever cover, console box and console
box front extension.
5) Remove front floor carpet.
INSTALLATION
Reverse removal sequence to install front floor carpet, noting fol-
lowing point.
When tightening seat belt anchor bolt, refer to Section 10A
ªFRONT SEAT BELTº for tightening torque.
LUGGAGE FLOOR CARPET
Luggage floor carpet is fixed to floor with clips.
REMOVAL
Detach clips, using care not to pull up carpet with force and break
clips. And remove inner trim.
INSTALLATION
Reverse removal sequence to install luggage floor carpet.