hood open SUZUKI GRAND VITARA 2003 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. ªUPPERº or ªLOWERº mark
MAINTENANCE AND LUBRICATION 0B-23
3) Visually check pump drive belt for cracks and wear.
4) Check belt for tension, referring to item 1-1.
If necessary, have belt adjusted or replaced.
ITEM 6-16
All Hinges, Latches and Locks Inspection
Doors
Check that each door of front, rear and back doors opens and
closes smoothly and locks securely when closed.
If any malfunction is found, lubricate hinge and latch or repair door
lock system.
Engine hood
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.). Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.
ITEM 6-17
Air Conditioning Filter (if equipped)
Inspection
1) Remove air conditioning filter from cooling unit referring to Sec-
tion 1B.
2) Check filter for dirt. Replace excessively dirty filter.
3) Blow off dust by compressed air from air outlet side of filter.
4) Install filter to cooling unit referring to Section 1B.
Replacement
Replace air conditioning filter with new one referring to Section 1B.

YH4
GRAND
VITARA
BODY SERVICE 9-21
1. Hood lock
2. Hood lock bolts
3. Match marks
1. Hood cushion
HOOD
REMOVAL
1) Remove window washer hose from hood.
2) Remove four mounting bolts to detach hood.
ADJUSTMENT

Fore-and-aft and right-and-left adjustment.
Loosen four mounting bolts for adjustment.

Hood lock adjustment
When installing hood lock, bring bolt at intersection point of match
marks and move it in vertical direction for adjustment, if neces-
sary.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)

Vertical adjustment
If only one side (right or left) of hood is not level with front fender,
make it level by tightening or loosening hood cushion.
INSTALLATION
Reverse removal procedure to install hood.
INSPECTION
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.) Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.

YH4
GRAND
VITARA
1. (a)
1. (a)
1
11
Tightening Torque
(a): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Bolt
BODY SERVICE 9-33
INSTRUMENTATION AND DRIVER INFORMATION
INSTRUMENT PANEL
WARNING:
See WARNING at the beginning of this section.
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº in
Section 10B.
3) Remove console box.
4) Remove glove box and column hole cover.
5) Disconnect wires and cables from heater unit and blower motor
assembly.
6) Remove steering column assembly. Refer to Section 3C1.
7) Disconnect speedometer connector and remove speedometer
assembly. If equipped with air bag, disconnect wire coupler at
SDM and air bag ground terminal for air bag.
8) Remove engine hood opener.
9) Disconnect couplers which need to be disconnected for removal
for instrument panel.
10) Remove instrument panel mounting screws.
11) Remove instrument panel mounting bolt.
12) Remove instrument panel.
CAUTION:
For vehicle with Air Bag, instrument panel could not be re-
moved with SDM coupler connected and ground terminal
installed.
Use care not to damage Air Bag harness.
INSTALLATION
1) Install instrument panel by reversing removal procedure, noting
the following items.

When installing each part, be careful not to catch any cable or
wiring harness.

When installing steering column assembly, refer to ªAIR BAG
STEERING COLUMN INSTALLATIONº in Section 3C1.
2) Adjust control cables. (Refer to Section 1A ªHEATER CON-
TROL CABLESº.)
3) Enable air bag system. Refer to ªEnabling Air Bag Systemº in
Section 10B.

YH4
GRAND
VITARA
9-36 BODY SERVICE
Sealer is applied to the specific joints of a vehicle dur-
ing production. The sealer is intended to prevent dust
from entering the vehicle and serves also as an anti-
corrosion barrier. The sealer is applied to the door and
hood hem areas and between panels. Correct and re-
seal the originally sealed joints if damaged. Reseal
the attaching joints of a new replacement panel and
reseal the hem area of a replacement door or hood.
Use a quality sealer to seal the flanged joints, overlap
joints and seams. The sealer must have flexible char-
acteristics and paintability after it's applied to repair
areas.
For the sealer to fill open joints, use caulking material.
Select a sealer in conformance with the place and
purpose of a specific use. Observe the manufactur-
er's label-stand instructions when using the sealer.
In many cases, repaired places require color painting.
When this is required, follow the ordinary techniques
specified for the finish preparation, color painting and
undercoating build-up.
Rust proof wax, a penetrative compound, is applied
to the metal-to-metal surfaces (door and side sill in-
sides) where it is difficult to use ordinary undercoating
material for coating. Therefore, when selecting the
rust proof wax, it may be the penetrative type.
During the undercoating (vinyl coating) application,
care should be taken that sealer is not applied to the
engine-related parts and shock absorber mounting or
rotating parts. Following the under coating, make
sure that body drain holes are kept open.
he sequence of the application steps of the anti-corro-
sion materials are as follows:
1) Clean and prepare the metal surface.
2) Apply primer.
3) Apply sealer (all joints sealed originally).
4) Apply color in areas where color is required such
as hem flanges, exposed joints and under body
components.
5) Apply anticorrosion compound (penetrative wax).
6) Apply undercoating (rust proof material).
PAINT AND COATINGS
ANTI-CORROSION TREATMENT
WARNING:
Standard shop practices, particularly eye
protection, should be followed during the per-
formance of the below-itemized operations to
avoid personal injury.
As rust proof treatment, steel sheets are given corro-
sion resistance on the interior and / or exterior.
These corrosion resistance steel sheet materials are
called one of two-side galvanized steel sheets.
It is for the sake of rust protection that these materials
are selected and given a variety of treatments as de-
scribed blow.
1) Steel sheets are treated with cathodic electroprim-
er which is excellent in corrosion resistance.
2) Rust proof wax coatings are applied to door and
side sill insides where moisture is liable to stay.
3) Vinyl coating is applied to body underside and
wheel housing inside.
4) Sealer is applied to door hem, engine compart-
ment steel sheet-to-steel sheet joint, and the like
portions to prevent water penetration and resulting
in rust occurrence.
In panel replacement or collision damage repair, leav-
ing the relevant area untreated as it is in any operation
which does disturb the above-mentioned rust proof
treatment will cause corrosion to that area. Therefore,
it is the essential function of any repair operation to
correctly recoat the related surfaces of the relevant
area.
All the metal panels are coated with metal condition-
ers and primer coating during vehicle production. Fol-
lowing the repair and / or replacement parts installa-
tion, every accessible bare metal surface should be
cleaned and coated with rust proof primer. Perform
this operation prior to the application of sealer and
rust proof wax coating.