Batter SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Connect one banana plug to positive terminal of power
source (12V vehicle battery) and then the other to
negative terminal to immediately activate.
2. Short to two deployment harness leads.
10B-86 AIR BAG SYSTEM
14) Notify all people in the immediate area that you intend to acti-
vate the seat belt pretensioner.
NOTE:

When the pretensioner activates, the rapid gas expan-
sion will create a substantial report. Wear suitable ear
protection. Notify all people in the immediate area that
you intend to activate the seat belt pretensioner and suit-
able ear protection should be worn.

When the pretensioner activates, the seat belt preten-
sioner may jump about 30 cm (1 ft) vertically. This is a
normal reaction of the seat belt pretensioner to the force
of the rapid gas expansion inside the pretensioner.
WARNING:
Safety precautions must be observed when handling
an activated seat belt pretensioner.

After activation, the metal surfaces of the seat belt
pretensioner will be very hot. Do not touch the metal
areas of the seat belt pretensioner for about 30 min-
utes after activation.

Do not place the activated seat belt pretensioner
near any flammable objects.

Do not apply water, oil, etc. to the activated seat belt
pretensioner.

If the activated seat belt pretensioner must be
moved before it is cool, wear gloves and handle it by
using nonmetal material.
Failure to follow procedures may result in fire or per-
sonal injury.
15) Separate the two banana plugs on the deployment harness.
16) Connect the deployment harness to the power source (12V ve-
hicle battery) to immediately activate the pretensioner.
17) Disconnect the deployment harness from power source (12V
vehicle battery) and short the two deployment harness leads
together by fully seating one banana plug into the other.

YH4
GRAND
VITARA
1. Shorted
Driver side for left hand steering vehicle
Driver side for right hand steering vehicle
1. Stretch deployment harness
to its full length 10 m (33 ft).
2. Drop cloth, blanket or similar item.
10B-90 AIR BAG SYSTEM
5) Check that there is no open/short or damage in special tool (de-
ployment harness). If any faulty condition is found, do not use
it and be sure to use new deployment harness.
Special Tool
(A): 09932-75030
6) Short the two deployment harness leads together by fully seat-
ing one banana plug into the other.
WARNING:
Deployment wires shall remain shorted and not be con-
nected to a power source until the pretensioner is to be
activated.
Special Tool
(A): 09932-75030
7) Connect the deployment harness connector to the seat belt
pretensioner harness and lock the connector with lock lever.
Special Tool
(A): 09932-75030
8) Route deployment harness out the vehicle.
9) Verify that the inside of the vehicle and the area surrounding
the vehicle are clear of all people and loose or flammable ob-
jects.
10) Stretch the deployment harness to its full length 10 m (33 ft).
11) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
12) Completely cover windshield area and front door window
openings with a drop cloth, blanket to similar item. This reduces
the possibility of injury due to possible fragmentation of the ve-
hicle's glass or interior.
13) Notify all people in the immediate area that you intend to acti-
vate the seat belt pretensioner.

YH4
GRAND
VITARA
1. Stretch it to full length 10m (33 ft).
2. Power source (12V vehicle battery)
3. Connect one banana plug to positive terminal of power
source (12V vehicle battery) and then the other to
negative terminal to immediately activate.
4. Short harness leads after activation.
5. Drop cloth, blanket or similar them.
AIR BAG SYSTEM 10B-91
NOTE:
When the pretensioner activates, the rapid gas expansion
will create a substantial report. Wear suitable ear protec-
tion. Notify all people in the immediate area that you intend
to activate the seat belt pretensioner and suitable ear
protection should be worn.
WARNING:
Safety precautions must be observed when handling an
activated seat belt pretensioner.

After activation, the metal surfaces of the seat belt
pretensioner will be very hot. Do not touch the metal
areas of the seat belt pretensioner for about 30 min-
utes after activation.

Do not apply water, oil, etc. to activated seat belt pre-
tensioner.

If the activated seat belt pretensioner must be moved
before it is cool, wear gloves and handle by using non-
metal material.
Failure to follow procedures may result in fire or per-
sonal injury.
14) Separate the two banana plugs on the deployment harness.
15) Connect the deployment harness to the power source (12 V ve-
hicle battery) to immediately activate the pretensioner.
16) Disconnect the deployment harness from the power source (12
V vehicle battery) and short the two deployment harness leads
together by fully seating one banana plug into the other.