Pin SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-71
AIR BAG (INFLATOR) MODULES DISPOSAL
WARNING:
Failure to follow proper air bag (inflator) module disposal procedures can result in air bag deployment
which may cause personal injury. Undeployed air bag (inflator) module must not be disposed of
through normal refuse channels.
The undeployed air bag (inflator) module contain substances that can cause severe illness or personal
injury if the sealed container is damaged during disposal.
Do not dispose of the live (undeployed) air bag (inflator) modules.
The method employed depends upon the final disposition of the particular vehicle, as noted in ªDeployment Out-
side Vehicleº and ªDeployment Inside Vehicleº in this section.
Deployment Outside Vehicle disposing of the air bag (inflator) module(s) only (i.e., the vehicle itself will be. . . . . .
used again).
Deployment Inside Vehicle scrapping the entire vehicle including the air bag (inflator) module(s).. . . . . . . .
DEPLOYMENT OUTSIDE VEHICLE
Use this procedure when the vehicle itself is used again (only the air bag (inflator) module(s) are disposed of).
WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.

To avoid an accidental deployment, this work should be performed by no more than one person.

The procedure should be followed strictly as described here.

Be sure to read ªService Precautionsº in this section for the air bag (inflater) module beforehand.

Never connect deployment harness to any power source before connecting deployment harness to
the air bag (inflator) module. Deployment harness shall remain shorted and not be connected to a
power source until the air bag is to be deployed.

Since a large amount of smoke is produced when air bag is deployed, select a well-ventilated area.

The air bag (inflator) module will immediately deploy the air bag when a power source is connected
to it. Wear safety glasses throughout this entire deployment and disposal procedure.

Wear suitable ear protection when deploying air bag. Also, advise those who are in the area close to
deployment site to wear suitable ear protection.

Do not deploy driver and passenger air bag (inflator) modules at the same time.
The following procedure requires use of special tool(s) (deployment harness and passenger air bag (inflator) mod-
ule deployment fixture). Do not attempt procedure without it (them).

YH4
GRAND
VITARA
10B-78 AIR BAG SYSTEM
DEPLOYMENT INSIDE VEHICLE
Use this procedure when scrapping the entire vehicle including the driver and passenger air bag (inflator) modules.
CAUTION:
When vehicle itself will be used again, deploy the air bag outside vehicle according to ªDeployment
Outside Vehicleº, for deploying it inside will cause the instrument panel, glove box and their vicinity
to be deformed.
Failure to observe this CAUTION may require unneeded vehicle inspection and repair.
WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.

To avoid an accidental deployment, this work should be performed by no more than one person.

The procedure should be followed strictly as described here.

Be sure to read ªService Precautionsº for the air bag (inflator) module beforehand.

Never connect deployment harness to any power source before connecting deployment harness to
the air bag (inflator) module. Deployment harness shall remain shorted and not be connected to a
power source until the air bag is to be deployed.

The air bag (inflator) module will immediately deploy the air bag when a power source is connected
to it. Wear safety glasses throughout this entire deployment and disposal procedure.

Wear suitable ear protection when deploying air bag. Also, advise those who are in the area close to
deployment site to wear suitable ear protection.

Do not deploy driver and passenger air bag (inflator) modules at the same time.
1) Turn ignition switch to ªLOCKº, remove key and put on safety
glasses.
2) Remove all loose objects from front seats and instrument panel.
3) [For driver air bag (inflator) module]
Disconnect contact coil connector (yellow connector) located
near the base of the steering column.
ii) Release locking of lock lever.
ii) After unlocked, disconnect to connector.
[For passenger air bag (inflator) module]
Remove glove box from instrument panel and disconnect pas-
senger air bag (inflator) module connector (yellow connector).
ii) Release locking of lock lever.
ii) After unlocked, disconnect to connector.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-83
SEAT BELT PRETENSIONERS DISPOSAL
WARNING:
Failure to follow proper seat belt pretensioner (retractor assembly) disposal procedures can result in
pretensioner activation which may cause personal injury. Inactivated seat belt pretensioner must not
be disposed of through normal refuse channels.
The inactivated seat belt pretensioner contain substances that can cause severe illness or personal
injury if the sealed container is damaged during disposal.
Do not dispose of the live (inactivated) seat belt pretensioners.
The method employed depends upon the final disposition of the particular vehicle, as noted in ªActivation Outside
Vehicleº and ªActivation Inside Vehicleº in this section.
Activation Outside Vehicle disposing of the seat belt pretension(s) only (i.e., the vehicle itself will be used. . . . . . . .
again).
Activation Inside Vehicle scrapping the entire vehicle including the seat belt pretensioners.. . . . . . . . . .
ACTIVATION OUTSIDE VEHICLE
Use this procedure when the vehicle itself is used again (only the seat belt pretensioner(s) are disposed of).
WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.

To avoid an accidental activation, this work should be performed by no more than one person.

The procedure should be followed strictly as described here.

Be sure to read ªService Precautionsº in this section for the seat belt pretensioner beforehand.

Never connect deployment harness to any power source before connecting deployment harness to
the seat belt pretensioner. Deployment harness shall remain shorted and not be connected to a power
source until the pretensioner is to be activated.

The seat belt pretensioner will immediately activate the pretensioner when a power source is con-
nected to it. Wear safety glasses throughout this entire activation and disposal procedure.

Wear suitable ear protection when activating pretensioner. Also, advise those who are in the area
close to activation site to wear suitable ear protection.

Do not activate driver and passenger seat belt pretensioners at the same time.
The following procedure requires use of special tools (deployment harness). Do not attempt procedure without it.

YH4
GRAND
VITARA
1. Air bag harness
2. Seat belt pretensioner harness
For driver side
AIR BAG SYSTEM 10B-89
ACTIVATION INSIDE VEHICLE
Use this procedure when scrapping the entire vehicle including the seat belt pretensioners.
CAUTION:
When vehicle itself will be used again, activate pretensioner outside vehicle according to ªActivation
Outside Vehicleº, for activating it inside will cause the center pillar inner garnish and their vicinity to
be deformed.
Failure to observe this CAUTION may require unneeded vehicle inspection and repair.
WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.

To avoid an accidental activation, this work should be performed by no more than one person.

The procedure should be followed strictly as described here.

Be sure to read ªService Precautionsº for the seat belt pretensioner beforehand.

Never connect deployment harness to any power source before connecting deployment harness to
the seat belt pretensioner. Deployment harness shall remain shorted and not be connected to a power
source until the pretensioner is to be activated.

The seat belt pretensioner will immediately activate the pretensioner when a power source is con-
nected to it. Wear safety glasses throughout this entire activation and disposal procedure.

Wear suitable ear protection when activating pretensioner. Also, advise those who are in the area
close to activation site to wear suitable ear protection.

Do not activate driver and passenger seat belt pretensioners at the same time.
1) Turn ignition switch to ªLOCKº, remove key and put on safety
glasses.
2) Remove all loose objects from front seats and instrument panel.
3) Remove both side (driver and passenger side) front pillar lower
trims and disconnect seat belt pretensioner harnesses from air
bag harness.
4) Confirm that each seat belt pretensioner is securely mounted.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-95
09931-76011
Suzuki scan tool (tech 1A) kit1. Storage case
2. Operator's manual
3. Tech 1A
4. DLC cable
5. Test lead/probe
6. Power source cable
7. DLC cable adapter
8. Self-test adapter Mass storage cartridge for air bag system
09931-76030
16/14 pin DLC cable09932-75010
Air bag driver/passenger
load tool09932-76010
Connector test adapter kit09932-75030
Air bag deployment harness
09932-75040
Passenger air bag (inflator)
module deployment fixtureDigital multimeter for
which the maximum test
current is 10 mA or less
at the minimum range of
resistance measurement.
WARNING:
Be sure to use the specified
digital multimeter.
Otherwise, air bag deploy-
ment or personal injury may
result.
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
SDM bolt60.64.5
Passenger air bag (inflator) modulescrew5.50.554.0Passenger air bag (inflator) modulebolt232.316.5
Driver air bag (inflator) module boltRefer to SECTION 3C1.
Seat belt pretensioner (retractor assembly) boltRefer to SECTION 10A.
SPECIAL TOOLS