Belt SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2004, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2004 2.GPages: 801, PDF Size: 12.15 MB
Page 3 of 801
YH4
GRAND
vol.1
0A
0B
1A
1B
3
3A
3B1
3C
3C1
3D
3E
3F
4A2
4B
5
6
7A5A
5B
5C
5E1
6A1
6A2
6A4
6B
6C
6E1
6E2
6F1
6F2
6G
6G1
6H
6K
7A1
7B1
7C1
7D
7E
7F
8
8B
8C
8D
8G
9
10
10A
8A
10B
6-1ENGINE
General Information and
Diagnosis (G16 / J20)
General Information and
Diagnosis (H25)
Engine Mechanical (G16)
Engine Mechanical (H25)
Engine Mechanical (J20)
Engine Cooling
Engine Fuel
Engine and Emission Control
System (SFI for G16 / J20)
Engine and Emission Control
System (SFI for H25)
Ignition System (G16)
Ignition System (J20 / H25)
Cranking System
(Reduction Type)
Cranking System
(No-Reduction Type)
Charging System
Exhaust System
TRANSMISSION, CLUTCH
AND DIFFERENTIAL
Manual Transmission (Type 1)
Manual Transmission (Type 2)
Automatic Transmission
Clutch (Hydraulic Type)
Transfer
Differential (Front)
Differential (Rear)
BODY ELECTRICAL SYSTEM
Wiring Diagram
Lighting System
Instrumentation / Driver
Information
Windows, Mirrors, Security
and Lock
Immobilizer Control System
BODY SERVICE
RESTRAINT SYSTEM
Seat Belt
Air Bag System GENERAL INFORMATION
General Information
Maintenance and Lubrication
TABLE OF CONTENTS TABLE OF CONTENTS SECTIONSECTION
0B
HEATING AND AIR
CONDITIONING
Heater and Ventilation
Air Conditioning
STEERING, SUSPENSION,
WHEELS AND TIRES
Front End Alignment
Power Steering (P / S) System
Steering Wheel and Column
(Not Equipped with Air Bag)
Air Bag Steering Wheel
and Column
Front Suspension
Rear Suspension
Wheel and Tires
1A
3A 0A
1B
3B1
3C
3C1
3D
3E
3F36A16
6A2
6A4
6B
6C
6E1
6E2
6F1
DRIVE SHAFT / PROP. SHAFT
Front Drive Shaft / Shaft
Bearing, Oil Seal
Propeller Shaft
BRAKES
Brake Pipe / Hose / Master
Cylinder
Front Brakes
Parking and Rear Brakes
Antilock Brake System
4A2
4B
5
5A
5B
5C
5E1
6F2
6G
6G1
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8
8A
8B
8C
8D
8G
9
10
10A
10B
6-1
NOTE:
The screen toned Sections 6 ± 6K are included in Volume 2 and Section 8A is in Wiring
Diagram Manual.
Page 6 of 801
YH4
GRAND
VITARA
1. Air bag wire harness
2. Passenger air bag
(inflator) module
3. SDM
4. DLC5. Contact coil
6. Driver air bag (inflator)
module
7. Seat belt pretensioner
(if equipped)
GENERAL INFORMATION 0A-3
PRECAUTIONS
PRECAUTION FOR VEHICLES EQUIPPED
WITH A SUPPLEMENTAL RESTRAINT
(AIR BAG) SYSTEM
WARNING:
The configuration of air bag system parts are as shown in
the figure. When it is necessary to service (remove, rein-
stall and inspect) these parts, be sure to follow proce-
dures described in SECTION 10B. Failure to follow proper
procedures could result in possible air bag system activa-
tion, personal injury, damage to parts or air bag system
being unable to activate when necessary.
If the air bag system and another vehicle system both
need repair, SUZUKI recommends that the air bag system
be repaired first, to help avoid unintended air bag system
activation.
Do not modify the steering wheel, dashboard, or any other
air bag system components. Modifications can adversely
affect air bag system performance and lead to injury.
If the vehicle will be exposed to temperatures over 93C
(200F) (for example, during a paint baking process), re-
move the air bag system components beforehand to avoid
component damage or unintended air bag system activa-
tion.
DIAGNOSIS
When troubleshooting air bag system, be sure to follow
ªDIAGNOSISº in SECTION 10B. Bypassing these proce-
dures may result in extended diagnostic time, incorrect diag-
nosis, and incorrect parts replacement.
Never use electrical test equipment other than that specified
in this manual.
WARNING:
Never attempt to measure the resistance of the air bag (in-
flator) modules (driver and passenger) and seat belt preten-
tioners (driver and passenger). It is very dangerous as the
electric current from the tester may deploy the air bag or ac-
tivate the pretensioner.
Page 8 of 801
YH4
GRAND
VITARA
1. Exhaust hole
1 1
NG
GENERAL INFORMATION 0A-5
WARNING:
SDM
During service procedures, be very careful when handling
a Sensing and Diagnostic Module (SDM). Never strike or
jar the SDM.
Never power up the air bag system when the SDM is not
rigidly attached to the vehicle. All SDM and mounting
bracket fasteners must be carefully torqued and the arrow
must be pointing toward the front of the vehicle to ensure
proper operation of the air bag system.
The SDM could be activated when powered while not rigid-
ly attached to the vehicle which could cause deployment
and result in personal injury.
WARNING:
Driver and Passenger Seat Belt Pretensioners
For handling and storage of a live seat belt pretensioner,
select a place where the ambient temperature below 65C
(150F), without high humidity and away from electric
noise.
Never carry seat belt pretensioner by wire or connector of
pretensioner. When placing a live seat belt pretensioner
on the workbench or some place like that, be sure not to
lay it with its exhaust hole provided side facing down. It is
also prohibited to put something on its face with an ex-
haust hole or to put a seat belt pretensioner on top of
another. Otherwise, personal injury may result.
Never dispose of live (inactivated) seat belt pretensioners
(driver and passenger). If disposal is necessary, be sure
to activate them according to activation procedures de-
scribed in SECTION 10B before disposal.
The seat belt pretensioner immediately after activation is
very hot. Wait for at least half an hour to cool it off before
proceeding the work.
With many service procedures, gloves and safety glasses
should be worn to prevent any possible irritation of the
skin or eyes.
Page 9 of 801
YH4
GRAND
VITARA
0A-6 GENERAL INFORMATION
CAUTION:
Even when the accident was light enough not to cause air
bags to activate, be sure to inspect system parts and other
related parts according to instructions under ªRepair and
Inspection Required after an Accidentº in SECTION 10B.
When servicing parts other than air bag system, if shocks
may be applied to air bag system component parts, re-
move those parts beforehand.
When handling the air bag (inflator) modules (driver and
passenger), seat belt pretensioners (driver and passen-
ger) or SDM, be careful not to drop it or apply an impact to
it. If an excessive impact was applied (e.g., dropped from
a height of 91.4 cm (3 feet) or more), never attempt disas-
sembly or repair but replace it with a new one.
When grease, cleaning agent, oil, water, etc. has got onto
air bag (inflator) modules (driver and passenger) or seat
belt pretensioners (drive and passenger), wipe off im-
mediately with a dry cloth.
Air bag wire harness can be identified easily as it is cov-
ered with a yellow protection tube. Be very careful when
handling it.
When an open in air bag wire harness, damaged wire har-
ness, connector or terminal is found, replace wire har-
ness, connectors and terminals as an assembly.
Do not apply power to the air bag system unless all com-
ponents are connected or a diagnostic chart requests it,
as this will set a diagnostic trouble code.
Never use air bag system component parts from another
vehicle.
When using electric welding, be sure to temporarily dis-
able air bag system referring to ªDisabling Air Bag Sys-
temº described in ªService Precautionsº under ªOn-Ve-
hicle Serviceº in SECTION 10B.
Never expose air bag system component parts directly to
hot air (drying or baking the vehicle after painting) or
flames.
WARNING / CAUTION labels are attached on each part of
air bag system components. Be sure to follow the instruc-
tions.
After vehicle is completely repaired, perform ªAir Bag
Diagnostic System Checkº described in ªDiagnosisº in
SECTION 10B.
Page 10 of 801
YH4
GRAND
VITARA
GENERAL INFORMATION 0A-7
GENERAL PRECAUTIONS
The WARNING and CAUTION below describe some general precautions that you should observe when servicing
a vehicle. These general precautions apply to many of the service procedures described in this manual, and they
will not necessarily be repeated with each procedure to which they apply.
WARNING:
Whenever raising a vehicle for service, be sure to follow the instructions under ªVEHICLE LIFTING
POINTSº on SECTION 0A.
When it is necessary to do service work with the engine running, make sure that the parking brake
is set fully and the transmission is in Neutral (for manual transmission vehicles) or Park (for automatic
transmission vehicles). Keep hands, hair, clothing, tools, etc. away from the fan and belts when the
engine is running.
When it is necessary to run the engine indoors, make sure that the exhaust gas is forced outdoors.
Do not perform service work in areas where combustible materials can come in contact with a hot
exhaust system. When working with toxic or flammable materials (such as gasoline and refrigerant),
make sure that the area you work in is well-ventilated.
To avoid getting burned, keep away from hot metal parts such as the radiator, exhaust manifold, tail-
pipe, muffler, etc.
New and used engine oil can be hazardous. Children and pets may be harmed by swallowing new or
used oil. Keep new and used oil and used engine oil filters away from children and pets.
Continuous contact with used engine oil has been found to cause [skin] cancer in laboratory animals.
Brief contact with used oil may irritate skin. To minimize your exposure to used engine oil, wear a
long-sleeve shirt and moisture-proof gloves (such as dishwashing gloves) when changing engine oil.
If engine oil contacts your skin, wash thoroughly with soap and water. Launder any clothing or rags
if wet with oil, recycle or properly dispose of used oil and filters.
Make sure the bonnet is fully closed and latched before driving. If it is not, it can fly up unexpectedly
during driving, obstructing your view and resulting in an accident.
CAUTION:
Before starting any service work, cover fenders, seats and
any other parts that are likely to get scratched or stained dur-
ing servicing. Also, be aware that what you wear (e.g, but-
tons) may cause damage to the vehicle's finish.
When performing service to electrical parts that does not re-
quire use of battery power, disconnect the negative cable of
the battery.
Page 29 of 801
YH4
GRAND
VITARA
0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE UNDER NORMAL DRIVING CONDITIONS
Interval:
This interval should be judged by
This table includes services as scheduled up to 90,000 km
(54,000 miles) mileage. Beyond 90,000 km (54,000 miles), carry
out the same services at the same intervals respectively.
This interval should be judged by
odometer reading or months,Km (x 1,000)153045607590g
whichever comes first.Miles (x 1,000)91827364554
Months122436486072
ENGINE
1-1. Drive beltV-beltIRIRIR
V-rib belt (Flat type)±±I±±R
1-2. Camshaft timing belt (G16 engine only)Replace every 100,000 km or
60,000 miles
1-3. Valve lash (clearance)G16 engine only±I±I±I
1-4. Engine oil and
oil filterJ20 / H25 engines
G16 engine with HO2S (SG, SH, SJ)RRRRRR
G16 engine with HO2S (SE, SF),
G16 engine without HO2SReplace every 10,000 km (6,000 miles)
or 8 months
1-5. Engine coolant±±R±±R
1-6. Exhaust system±I±I±I
IGNITION SYSTEM
2-1. Spark plugs
Wh
Vehicle without
HO2S
Nickel plug±R±R±R
When
unleaded
HO2SIridium plug±±±R±±unleaded
fuel isVehicle with
HO2S
Nickel plug±±R±±Rfuel is
usedHO2SIridium plugReplace every 105,000 km or 63,000
miles
When leaded fuel is used, refer to ªSevere Driving Conditionº schedule
FUEL SYSTEM
3-1. Air cleaner filterIIRIIR
3-2. Fuel lines and connections±I±I±I
3-3. Fuel filterReplace every 105,000 km or 63,000
miles
3-4. Fuel tank±±I±±I
EMISSION CONTROL SYSTEM
4-1. Crankcase ventilation hoses and connections
(Vehicle without HO2S)±±I±±I
4-2. PCV valveVehicle without HO2S±±I±±I
Vehicle with HO2S±±±±±I
4-3. Fuel evaporative emission
tl t
Vehicle without HO2S±I±I±I
control systemVehicle with HO2S±±±±±I
NOTES:
ªRº : Replace or change
ªIº : Inspect and correct, replace or lubricate if necessary
For Item 1-2. Camshaft timing belt: This belt may be replaced every 90,000 km (54,000 miles) according
to customer's maintenance convenience.
For Sweden, item 2-1, 4-2 and 4-3 should be performed by odometer reading only.
For Item 2-1. Spark plugs, replace every 50,000 km if the local law requires.
Nickel spark plug: BKR6E-11 or K20PR-U11
Iridium spark plug: IFR6E11 or SK20PR-A11 for G16 engine, IFR5J11 or SK16PR11 for J20 / H25 engines
Page 31 of 801
YH4
GRAND
VITARA
0B-4 MAINTENANCE AND LUBRICATION
MAINTENANCE RECOMMENDED UNDER SEVERE DRIVING CONDITIONS
If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is
recommended that applicable maintenance operation be performed at the particular interval as given in the chart
below.
Severe condition code
A ± Repeated short trips E ± Repeated short trips in extremely
B ± Driving on rough and / or muddy roads cold weather
C ± Driving on dusty roads F ± Leaded fuel use
D ± Driving in extremely cold weather G ± ± ± ± ± ± ± ± ±
and / or salted roads H ± Trailer towing (if admitted)
Severe
Condition Code
MaintenanceMaintenance
OperationMaintenance Interval
BCDITEM 1-1IEvery 15,000 km
(9,000 miles) or 12 months
± B C D ± ± ± ±Drive belt (V-rib belt)REvery 45,000 km
(27,000 miles) or 36 months
A ± C D E F ± HITEM 1-4
Engine oil and oil filterREvery 5,000 km
(3,000 miles) or 4 months
± B ± ± ± ± ± ±ITEM 1-6
Exhaust pipe mountingsIEvery 15,000 km
(9,000 miles) or 12 months
CITEM 3-1IEvery 2,500 km
(1,500 miles)
± ± C ± ± ± ± ±Air cleaner filter*1REvery 30,000 km
(18,000 miles) or 24 months
ABC EF HITEM 2-1Nickel plugREvery 10,000 km
(6,000 miles) or 8 months
A B C ± E F ± HSpark plugsIridium plugREvery 30,000 km
(18,000 miles) or 24 months
± B ± D E ± ± HITEM 6-9
Propeller shafts and drive shaftsIEvery 15,000 km
(9,000 miles) or 12 months
± B ± ± E ± ± H
ITEM 6-10, 6-12, 6-13
Manual transmission,
transfer and differential oil
REvery 30,000 km
(18,000 miles) or 24 months
± B ± ± E ± ± HITEM 6-11
Automatic transmission fluidREvery 30,000 km
(18,000 miles) or 24 months
± B ± ± ± ± ± ±ITEM 6-8
Suspension bolts and nutsTEvery 15,000 km
(9,000 miles) or 12 months
± B C D ± ± ± HITEM 6-7
Wheel bearingIEvery 15,000 km
(9,000 miles) or 12 months
CD
ITEM 6-17
Air conditioning filter*2
IEvery 15,000 km
(9,000 miles) or 12 months
± ± C D ± ± ± ±Air conditioning filter 2
(if equipped)REvery 45,000 km
(27,000 miles) or 36 months
NOTES:
ªIº : Inspect and correct, replace or lubricate if necessary
ªRº : Replace or change
ªTº : Tighten to the specified torque
*1 : Inspect or replace more frequently if necessary.
*2 : Clean or replace more frequently if the air from the air conditioning decreases.
Page 32 of 801
YH4
GRAND
VITARA
1. Crankshaft pulley
2. Water pump pulley
3. 100 N, 10 kg or 22 lb
G16
H25
MAINTENANCE AND LUBRICATION 0B-5
MAINTENANCE SERVICE
ENGINE
ITEM 1-1
Drive Belt Inspection and Replacement
WARNING:
All inspection and replacement are to be performed with
ENGINE NOT RUNNING.
Water pump and generator drive belt (G16 and H25 engines)
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any defect exists, replace.
Check belt for tension.
Water pump and generator belt tension
ªaº: 6 ± 8 mm (0.24 ± 0.32 in.) deflection for G16, 9 ± 11 mm
(0.35 ± 0.43 in.) deflection for H25 under 100 N, 10 kg or
22 lb pressure
NOTE:
When replacing belt with a new one, adjust belt tension to
5 ± 6 mm (0.20 ± 0.24 in.) for G16, 7 ± 9 mm (0.28 ± 0.35 in.)
for H25.
3) If belt is too tight or too loose, adjust it to specification by adjust-
ing alternator position.
4) Tighten alternator adjusting bolt and pivot bolts.
5) Connect negative cable to battery.
Replacement
Replace belt. Refer to Section 6B for replacement procedure of
pump belt.
Page 33 of 801
YH4
GRAND
VITARA
J20
J20
1. 100 N, 10 kg or 22 lb
2. Fan pulley3. Crankshaft pulley
4. Adjusting and pivot bolt
0B-6 MAINTENANCE AND LUBRICATION
Water pump, generator, power steering and / or A / C
compressor (if equipped) drive belt (J20 engine)
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any of above conditions are found, replace.
Also, check belt for tension.
Tension indicator ªBº should be the right of indicator ªAº as
shown in figure. If indicator ªBº is found to the left of indicator ªAº,
replace generator belt.
Replacement
Replace belt referring to Section 6H for replacement procedure of
generator drive belt.
Engine cooling fan drive belt (J20 engine)
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any defect exists, replace. Check belt for tension.
Cooling fan belt tension
ªaº: 5 ± 7 mm (0.20 ± 0.27 in.) deflection under 100 N, 10 kg
or 22 lb pressure.
NOTE:
When replacing belt with a new one, adjust belt deflection
to 4 ± 5 mm (0.16 ± 0.19 in.).
3) If the belt is too tight or too loose, adjust it to specification by ad-
justing cooling fan pulley position.
4) Tighten adjusting bolt and pivot bolt.
5) Connect negative cable at battery.
Replacement
Replace belt referring to Section 6B for replacement procedure of
cooling fan drive belt.
Page 34 of 801
YH4
GRAND
VITARA
G16 with P / S
G16 with P / S and A / C
H25 with P / S
H25 with P / S and A / C
1. Crankshaft pulley
2. P / S pump pulley
3. A / C compressor pulley
(if equipped)4. Tension pulley
5. Tension pulley bolts
MAINTENANCE AND LUBRICATION 0B-7
Power steering pump and / or A / C compressor drive belts (if
equipped) for G16 and H25 engines.
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any defect exists, replace.
Check belt for tension.
Power steering pump and / or A / C compressor drive belt
tension.
ªaº: 6 ± 9 mm (0.24 ± 0.35 in.) deflection under 100 N, 10 kg
or 22 lb pressure.
ªbº: 4 ± 7 mm (0.16 ± 0.28 in.) deflection under 100 N, 10 kg
or 22 lb pressure.
If belt tension is out of above specification, adjust it referring to
Section 1B or 3B1.
3) Connect negative cable to battery.
Replacement
Replace belt referring to Section 1B or 3B1 for replacement proce-
dure of belt.