Roof lining SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2004, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2004 2.GPages: 801, PDF Size: 12.15 MB
Page 587 of 801
YH4
GRAND
VITARA
8D-32 WINDOWS, MIRRORS, SECURITY AND LOCKS
3. To open
4. To close
3. Left turn
4. Right turn
Terminal
Switch
Terminal
Switch
POWER SLIDING ROOF (IF EQUIPPED)
INSPECTION
SLIDING ROOF SWITCH
Check switch for continuity between terminals as shown below.
Slide Switch (1)
CDFCDF
OPEN
OFF
CLOSE
Tilt Switch (2)
EDBEDB
UP
OFF
DOWN
SLIDING ROOF MOTOR ASSEMBLY
1) Remove head lining. Refer to Section 9 for detail.
2) Remove sliding roof motor assembly (1).
3) Connect known-good sliding roof switch (2) to sliding roof motor
assembly.
4) Connect 12 V battery positive terminal to terminal ªAº of motor
assembly (1) and battery negative terminal to terminal ªBº of mo-
tor assembly (1).
5) Check that the sliding roof motor (1) runs according to the move-
ment of the sliding roof switch (2).
Sliding Roof Switch
Motor
Tilt upturns left
Tilt downturns right
Slide openturns right
Slide closeturns left
If motor does not operate as above, replace sliding roof motor
assembly (1).
Page 619 of 801
YH4
GRAND
VITARA
9
BODY SERVICE 9-1
GLASS, WINDOWS AND MIRRORS9- 2 . . . . .
Front Door Glass 9- 2. . . . . . . . . . . . . . . . . . . . .
Front Door Window Regulator 9- 5. . . . . . . . . .
Windshield 9- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door Glass 9-12. . . . . . . . . . . . . . . . . . . . .
Rear Door Window Regulator 9-14. . . . . . . . . .
Quarter Window 9-15. . . . . . . . . . . . . . . . . . . . . .
Back Door Glass 9-16. . . . . . . . . . . . . . . . . . . . .
BODY STRUCTURE9-17 . . . . . . . . . . . . . . . . . . .
Front Door Assembly 9-17. . . . . . . . . . . . . . . . .
Rear Door Assembly 9-18. . . . . . . . . . . . . . . . . .
Back Door / Rear Gate Assembly 9-19. . . . . . . .
Hood 9-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Fender 9-22. . . . . . . . . . . . . . . . . . . . . . . . .
Front Bumper 9-23. . . . . . . . . . . . . . . . . . . . . . . .
Rear Bumper 9-24. . . . . . . . . . . . . . . . . . . . . . . .
Under Body Dimensions 9-25. . . . . . . . . . . . . . .
Body Dimensions 9-26. . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER
INFORMATION9-33 . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9-33. . . . . . . . . . . . . . . . . . . . .
SEAT9-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat 9-34. . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Seat 9-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
PAINT AND COATINGS9-36 . . . . . . . . . . . . . . . .
Anti-Corrosion Treatment 9-36. . . . . . . . . . . . . .
Metal Replacement Parts Finishing 9-37. . . . .
Plastic Parts Finishing 9-58. . . . . . . . . . . . . . . . .
SECURITY AND LOCKS9-59 . . . . . . . . . . . . . . . .
Front Door Lock Assembly 9-59. . . . . . . . . . . . .
Rear Door Lock Assembly 9-61. . . . . . . . . . . . .
Back Door / Rear Gate Lock Assembly 9-62. . .
Key Coding 9-63. . . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF / CONVERTIBLE TOP9-64 . . . . . . . . .
Sliding Roof (if equipped) 9-64. . . . . . . . . . . . . .
Canvas Top And Topbow Frames 9-71. . . . . . .
EXTERIOR AND INTERIOR TRIM9-72 . . . . . . .
Floor Carpet 9-72. . . . . . . . . . . . . . . . . . . . . . . . .
Head lining 9-73. . . . . . . . . . . . . . . . . . . . . . . . . .
Roof Trim (2 Door Model) 9-75. . . . . . . . . . . . . .
Side Moldings (if equipped) 9-77. . . . . . . . . . . .
Splash Guard (if equipped) 9-78. . . . . . . . . . . .
Roof Rail (if equipped) 9-79. . . . . . . . . . . . . . . .
Roof Molding 9-79. . . . . . . . . . . . . . . . . . . . . . . .
Luggage Under Box 9-80. . . . . . . . . . . . . . . . . .
SECTION 9
BODY SERVICE
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
When body servicing, if shock may be applied to air bag system component parts, remove those parts
beforehand. (Refer to Section 10B.)
NOTE:
Fasteners are important attaching parts in that they could affect the performance of vital components and
systems, and / or could result in major repair expense. They must be replaced with one of the same part
number of with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute a design. Torque values must be used as spe-
cified during reassembly to assure proper retention of these parts.
CONTENTS
Page 625 of 801
YH4
GRAND
VITARA
1. Eyeleteer
1. Piano string
2. Windshield
3. Windshield knife
BODY SERVICE 9-7
REMOVAL
1) Clean both inside and outside of glass and around it.
2) Remove wiper arms and garnish.
3) Using tape, cover body surface around glass to prevent any
damage.
4) Remove rear view mirror, sunvisor, and front pillar trims (right
& left).
5) If necessary, remove instrument panel. Refer to ªINSTRU-
MENT PANELº in this section.
6) If necessary, remove head lining. Refer to ªHEAD LININGº in
this section.
7) If necessary, remove roof trim. Refer to ªROOF TRIMº in this
section.
8) Remove (or cut) windshield molding all around until windshield
edge comes out.
9) Drill hole with eyeletter through adhesive and let piano string
through it.
10) Cut adhesive all around windshield with piano string.
When using tool to cut adhesive, be careful not to cause dam-
age to windshield. Use wire to cut adhesive along lower part of
windshield.
NOTE:
Use piano string as close to glass as possible so as to pre-
vent damage to body and instrument panel.
Page 647 of 801
YH4
GRAND
VITARA
ªa ± b'º : 448 mm (17.64 in.)
ªa ± f'º : 1054 mm (41.50 in.)
ªa ± hº : 926 mm (36.43 in.)
ªa ± gº : 1050 mm (41.34 in.)
ªb ± b'º : 888 mm (34.96 in.)
ªb ± dº : 400 mm (15.75 in.)
ªb' ± fº : 1314 mm (51.73 in.)
ªb ± eº : 837 mm (32.95 in.)
ªb ± fº : 892 mm (35.12 in.)ªb' ± cº : 650 mm (25.59 in.)
ªb' ± gº : 996 mm (39.21 in.)
ªb' ± fº : 1314 mm (51.73 in.)
ªc ± dº : 1245 mm (49.02 in.)
ªc ± eº : 1293 mm (50.90 in.)
ªf ± f'º : 1030 mm (40.55 in.)
ªf' ± gº : 512 mm (20.16 in.)
ªg ± hº : 808 mm (31.79 in.)
ªg ± g'º : 1544 mm (60.79 in.)
a. Clip hole in the center of head lining rear installation section
b (b'). Innermost end of roof panel installation section
c. Installation hole in upper part of back door striker
d. Installation hole in uppermost part of upper hinge
e. Installation hole in uppermost part of lower hinge
f (f'). Innermost end of rear floor tail member installation section
g (g'). Installation hole in outer upper section of R-COMB R lamp
h. Nut hole
BODY SERVICE 9-29
4 door model
Page 684 of 801
YH4
GRAND
VITARA
1. Spot light
2. Head lining
3. Sunvisor assemblies
4. Room light
5. Trim
6. Assist grips
1. Sliding roof motor
2. Mounting screw
1. Motor assy
2. Hole (body)
3. Hole (cam)
9-66 BODY SERVICE
SLIDING ROOF MOTOR / RELAY
REMOVAL
1) Remove head lining, refer to HEAD LINING REMOVAL in this
section.
2) Disconnect coupler and remove sliding roof motor assembly by
removing 3 screws.
CAUTION:
After removing sliding motor assembly, do not move
guide and link.
INSTALLATION
For installation, reverse removal procedure, noting following point.
Before installing, connect coupler and push the CLOSE side of the
slide switch.
Page 685 of 801
YH4
GRAND
VITARA
BODY SERVICE 9-67
1. Drain hoses
1. Sliding roof motor
2. Coupler
1. Sliding roof assembly fixing nuts
2. Sliding roof assembly
SLIDING ROOF ASSEMBLY
REMOVAL
1) Remove roof lining. Refer to HEAD LINING REMOVAL in this
section.
2) Remove sliding roof glass. Refer to SLIDING ROOF GLASS
REMOVAL.
3) Disconnect drain hoses connected to sliding roof assembly at 4
locations.
4) Disconnect sliding roof motor at coupler.
5) Remove 6 nuts and then remove sliding roof assembly.
Page 691 of 801
YH4
GRAND
VITARA
BODY SERVICE 9-73
5
46
4. Assistant grip
5. Rear room light
6. Inner trim
1. Roof harness
2. Rear washer hose
3. Adhesive tape
Front 1. Room light
2. Sunshade assembly
3. Spot light
IWATA
CAMI
HEAD LINING
REMOVAL
1) Remove spot light and sliding roof switch (if equipped).
2) Remove sunshade assembly.
3) Remove room light and spacer.
4) Remove assistant grips.
5) Remove inner trims covering head lining and door opening trim.
6) Remove rear speaker cover (if equipped).
7) Disconnect rear washer hose and roof harness from body.
8) Remove head lining.
NOTE:
Adhesive double coated tape is used to attach rear part of
head lining. Detach head lining from roof after removing all
above parts.
INSTALLATION
1) Set roof harness and washer hose to head lining with tape.
2) Clean roof where adhesive tape of head lining will be attached.
3) Peel off release liner of adhesive tape on head lining and install
it to body.
4) Install assistant grips a, b, c and d in that order.