warning SUZUKI GRAND VITARA 2008 3.G Operating Manual

Downloaded from www.Manualslib.com manuals search engine Gearshift lever
EXAMPLE
66J056
The gearshift lever is designed that it can not be shifted out of the "P" position unless the ignition switch is in the "ON" position
and the brake pedal is depressed.
A WARNING
Always depress the brake pedal before shifting from "P" (Park) (or "N" (Neutral) if the vehicle is station­ary) to a forward or reverse gear, to help prevent the vehicle from moving unexpectedly when you shift.
For all normal driving, make sure that the "POWER" indicator light is off, then put the
gearshift lever into "0" (Drive). Use. the
other gearshift lever positions as described below:
P (Park) Use this position to lock the transmission
when the vehicle is parked or when start­ing the engine. Shift into Park only when
the vehicle is completely stationary.
A WARNING
If you have a 4-wheel drive vehicle, never leave the transfer switch in uN" (Neutral) when parked.
Otherwise the vehicle may roll even if the transmission is in Park.
R (Reverse)
Use this position to reverse the vehicle
from stop. Make sure that vehicle is com­
pletely stationary before shifting into
Reverse.
N (Neutral) Use this position for starting the engine if
the engine stalls and you need to restart it while the vehicle is moving. You may also shift into Neutral and depress the brake pedal to hold the vehicle stationary during idling.
OPERATING YOUR VEHICLE
D (Drive) Use this position for all normal driving.
With the gearshift
lever in "0" range you can get an automatic downshift by press­ing the accelerator pedal. The higher the vehicle speed is, the more you need to press the accelerator pedal to get a down­shift.
4 (Low 3) . Use this position for driving on moderate uphill and downhill gradients. The engine
braking effect on moderate downhills can be used in this position. The transmission
shifts up only to 4th gear.
3 (Low 2) Use this position to provide extra power
when climbing hills, or to provide engine
braking when going down hills.
NOTE: In these 4 or 3 positions, if the power mode
selector switch is turned to the "ON" posi­tion, the transmission will not downshift
into "I.!' (Low 1).
L (Low 1) Use this position to provide maximum
power when climbing steep hills or driving
through deep snow or mud, or to provide
maximum engine braking when going
down steep
hills.
3-14

Downloaded from www.Manualslib.com manuals search engine Slippery road mode
When the "AfT POWER" switch is on with
shift in "2" (Low 2) position, the gear will be
fixed in second while driving or when start
driving. Therefore, you can drive smoothly
on slippery road.
NOTE: • When you start driving with the gearshift lever in "2" (Low 2) position while the "AI T POWER" switch is on, the gear will be fixed in second. If you need to shift up, shift the' lever into "3" (Low 3) or "0" (Drive) position. • When the "AfT POWER" is on, if you
shift the gearshift lever from "3" (Low 3) or "0" (Drive) position to "2" (Low 2) posi­tion, the gear will be fixed in second. Gearshift
lever
64J142
The
gearshift lever is designed that it can­not be shifted out of the "P" position unless
the ignition switch is in the "ON" position and. the brake pedal is depressed.
A WARNING
Always depress the brake pedal before shifting from' "P" (Park) (or "N" (Neutral) if the vehicle is station­ary) to a forward or reverse gear, to help prevent the vehicle from moving
unexpectedly when you shift.
OPERATING YOUR VEHICLE
For all normal driving, make sure that the "POWER" indicator light is off, then put the
gearshift lever into "0" (Drive). Use the
other gearshift lever positions as described
below: .
P (Park)
Use this position
to lock the transmission
when the vehicle is parked or when start­ing the engine. Shift into Park only when
the vehicle is completely stationary.
A WARNING
If you have a 4-wheel drive vehicle,
never leave the transfer switch in "N" (Neutral) when parked.
Otherwise the vehicle may roll even if the transmission is in Park ..
R (Reverse) Use this position to reverse the vehicle from stop. Make sure that vehicle is com­
pletely stationary before shifting into
Reverse.
N (Neutral)
Use this position for starting the engine if
the engine
stalls and you need to restart it while the vehicle is moving. You may also
shift into Neutral and depress the brake
pedal to hold the I('ehicle stationary during
idling.
3-16

Downloaded from www.Manualslib.com manuals search engine Description of Transfer Switch Positions
N (Neutral)
64J223
OPERATING YOUR-VEHICLE
In this position, engine power is not sup­plied to the front or rear axles. Only use
this position for towing your vehicle. When you turn the transfer switch to the "N" position, "N" indicator will come on with
the buzzer sound.
A. WARNING
Never leave the transfer switch in UN" (Neutral) when parked.
When the transfer switch is in uN"
(Neutral), the vehicle may roll even if the transmission is in gear or in Park.
3-20

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
From 4H to N
64J209
Stop the vehicle completely, place the
transmission in uN" (Neutral) and depress
the brake pedal and the clutch pedal fully (if equipped), then push in and turn the
switch to the mark (1) at the left of the uN" position, and hold the switch in this posi­
tion for 5 seconds until the uN" indicator blinks, then turn the switch to the uN" posi­
tion. When
you turn the transfer switch to the uN" position, uN" indicator will come on with
the buzzer sound.
3-25
CAUTION
• Be sure to stop the vehicle com­
pletely before operating the trans­fer switch to shift between "N" and "4H", or between "4H LOCK" and "4L LOCK".
• Do not shift between "4H" and "4H
LOCK" unless the front wheels are
in the straight-ahead position and
we recommend
that the vehicle speed be less than 1 00 km/h (60 mph).
Do not operate the transfer switch
while tires are racing.
• Do not operate your vehicle in "4H
LOCK" or "4L LOCK" on dry, hard
surfaces. (Continued)
CAUTION
(Continued) • Do not operate the vehicle while a
4WD mode indicator is blinking except when shifting between "4H" and "4L LOCK".
If you operate the vehicle while a
4WD mode indicator is blinking, a
buzzer will sound and the transfer will shift to "N" (Neutral) to prevent
transfer case damage.
In this case, use the following pro­cedure.
1) Release your foot from the accel­erator pedal and depress the
brake pedal to stop the vehicle
completely.
2) Depress the clutch pedal fully (if
equipped) or shift the automatic transmission gearshift lever to the "N" position. 3) If the transfer does not shift from "N" although you perform 1) and 2), turn the transfer switch to the
position previously selected and
operate the switch again.
NOTE: The information display shows the warning
and indicator message when the transfer
system
is operated, or has a problem.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Warning and Indicator messages
Transfer
Switch Operation Warning
and Indicator messages
In any position
In "N" position
Switching between
"4H" and "4H LOCK"
In "4H" position
3-27
I 79K074
79K077
79K078
I t¢-I USE 4HL MC'DE
79K079
Master Warn­ing Indicator
Blinks
Blinks
Off
Blinks
Sound
Off
Series
of
Beeps
Off
Beep
Cause and Remedy
There may be a problem with the 4WD
system.
Have your vehicle inspected by an
authorized
SUZUKI dealer.
This message informs you that the
transfer switch is in
"N", which is used only for towing your vehicle,
Move the transfer switch to a different
position
unless you are planning to tow
your vehicle,
This message informs you the 4WD
mode is switching,
Tires are slipping,
Turn the transfer switch to
"4H LOCK" or "4L LOCK" position.

Downloaded from www.Manualslib.com manuals search engine Transfer Switch Operation
Switching between U4H LOCK" and U4L LOCK"
Switching between U4H" and UN"
Warning and Indicator messages
I 1).'110 .8.CCEL ':'FF 1<>1 OE."-.RSHIFT I·.J
79K080
79K081
79K082
I 1<>1 SV'-iIT':Hlf'.JG
79K083
Master Warn­ing Indicator
Off
Off
Off
Off
Sound
Series of Beeps
Series of Beeps
Beep or
Off
Off
OPERATING YOUR VEHICLE
Cause and Remedy
(For automatic transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal.
Shift the automatic transmission gear­shift lever to the uN" position.
(For
manual transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal and clutch
pedal.
The desired transfer gear has not been
engaged.
Turn the transfer switch back to the pre­
viously selected position, and operate
the transfer switch again.
This message informs
you the 4WD
mode is switching.
Do not move your vehicle.
3-28

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Cruise Control (if equipped)
79K032
The cruise control system allows you to maintain a steady speed without keeping
your foot on the accelerator pedal. The controls for operating the cruise control system are on the steering wheel. You can
use the cruise control system at speeds of
about 40 km/h (25 mph) or higher.
A WARNING
To help avoid loss of vehicle control, do not use the cruise control system
when driving in heavy traffic, on slip­pery or winding roads, or on steep
downgrades.
3-29
NOTE: If the transfer switch (if equipped) is in the "4L LOCK" position, you can not use the
cruise control system. Refer to "Using the
Transfer Switch (if equipped)" in this sec­
tion.
CRUISE
52Dl13
When you push the "ON/OFF" switch, the
system is on and a "CRUISE" indicator light on the instrument cluster will be on.
SET
65D474
When the vehicle's speed is controlled by the cruise control system, a "SET' indica­
tor light on the instrument cluster will be on.
(2) ----\-l~
(4) (1)
79K049
To Set Cruising Speed Turn on the cruise control system by push­
ing the "ON/OFF" switch (1). Accelerate to the desired speed and push the "SET/
COAST' switch (3). Take your foot off the accelerator pedal and the set speed will be maintained.
With the cruise
control on, you can increase speed for passing by using the accelerator pedal. When you take your foot
off the pedal, your vehicle will return to the
set speed.
To Change Cruising Speed To reset the cruise control to a slower speed, hold in the "SET/COAST' switch (3) until the vehicle has slowed to the desired
speed, then release the switch. The new
speed will be maintained.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A WARNING
If
water gets into the brake drums,
brake performance may become poor
and unpredictable.
After driving through water or wash­
ing the underside of the vehicle, test
the brakes while driving at a slow speed to see if they have maintained
their normal effectiveness. If the
brakes are less effective than normal, dry them by repeatedly applying the
brakes while driving slowly until the
brakes have regained their normal effectiveness.
Power Assisted Brakes Your vehicle has power assisted brakes. If power assistance is lost due to a stalled engine or other failures, the system is still
fully operational on reserve power and you can bring the vehicle to a complete stop by pressing the brake pedal once and holding it down. The reserve power is partly used
up when you depress the brake pedal and reduces each time the pedal is pressed. Apply smooth and even pressure to the pedal. Do not pump the pedal.
3-31
A WARNING
Even without reserve power in the
brake system, you can still stop the vehicle by pressing the brake pedal harder than normally required. How­ever, the stopping distance may be longer.
Brake Assist System When you slam the brakes on, the brake
assist system judges as an emergency
stop and provides more powerful braking
for a driver who cannot hold down the
brake pedal firmly.
NOTE: If you quickly and forcefully depress the
brakes, you may hear a clicking sound in
the brake pedal. This is normal and indi­
cates that the brake assist system is acti­
vated properly.
Anti-Lock Brake System (ABS) ASS will help you avoid skidding by elec­
tronically controlling braking pressure. It
will also help you maintain steering control when braking on slippery surfaces or when
braking hard.
The
ASS works automatically, so you do
not need any special braking technique.
Just push the brake pedal down without
pumping. The ASS will operate whenever it
senses that the wheels are locking up. You may feel the brake pedal pulsate while the ASS is operating.
NOTE: The ABS will not work if vehicle speed is under about 5 - 6 kmlh (3 - 4 mph).
A WARNING
•
On some types of loose surfaces
(such as gravel, snow-covered
roads, etc.) the stopping distance
required for
an ABS-equipped vehi­cle may be slightly greater than for
a comparable vehicle with a con­ventional brake system. With a conventional brake system, skid­
ding tires are able to "plow" the gravel or snow layer, shortening
the stopping distance, ABS mini­
mizes this resistance effect. Allow for extra stopping distance when driving on loose surfaces. • On regular paved roads, some driv­
ers may be able to obtain slightly shorter stopping distances with
conventional brake systems than
with
ABS. • In both of the above conditions, ABS wi II still offer the advantage of helping you maintain directional control. However, remember that ABS will not compensate for bad road or weather conditions or poor
driver judgment. Use good judg­
ment and do not drive faster than
conditions will
safely allow.

Downloaded from www.Manualslib.com manuals search engine (8) or ABS
(1) (2)
(CD)
BRAKE (3)
(1) ABS warning light Type 1 (2) ABS warning light Type 2 (3) Brake system warning light
A WARNING
65D451
If the ABS warning light «1) or (2» on
the instrument panel comes on and
stays on while driving, there may be a
problem with the ABS system. If this happens:
1) Pull off the road and stop care­
fully.
2) Turn the ignition switch to "LOCK" and then start the engine again.
(Continued)
A WARNING
(Continued) If the warning light comes on briefly then turns off, the system is normal.
If the. warning light still stays on,
have the system inspected by your
SUZUKI dealer immediately.
If the ABS system becomes inopera­tive, the brake system will function as
an ordinary brake system that has no
ABS.
A WARNING
If the ABS warning light «1) or (2» and the Brake system warning light (3) on the instrument panel simulta­
neously stays on or comes on when
driving, both anti-lock function and
rear brake force control function (pro­portioning valve function) of the ABS system may have failed. If so, the rear wheels may easily skid or the vehicle can even spin in the worst case when
braking on a slippery road or when
hard braking even on a dry paved
road. Ask your SUZUKI dealer to inspect the ABS system immediately. Drive carefully, avoiding hard braking
as much as possible.
OPERATING YOUR VEHICLE
How the ABS Works A computer continuously monitors wheel speed. The' computer compares the
changes in wheel speed when braking. If the wheels slow suddenly, indicating a
skidding Situation, the computer will change braking pressure several times
each second to prevent the wheels from locking. When you start your vehicle or when you accelerate after a hard stop, you may hear a momentary motor or clicking sound as the system resets or checks itself.
A WARNING
The ABS may not work properly if
tires or wheels other than those
specified in the owner's manual are
used. This is because the ABS works
by comparing changes in wheel speed. When replacing tires or wheels, use only the size and type
specified in this owner's manual.
3-32

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Electronic Stability Program
(ESP~ (if equipped)
ESP® is a registered trademark of Daimler AG.
The Electronic Stability Program (ESP~ helps to control the vehicle during corner­
ing if front wheels or rear wheels skid. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the
engine's output, and by selectively apply­ing the brakes. In addition, ESP® helps to
avoid skidding by controlling braking pres­
sure.
A WARNING
The ESP® cannot enhance the vehi­
cle's driving stability in all situations and does not control your vehicle's entire braking system. The ESP® can­not prevent accidents, including those resulting from excessive speed
in turns, or hydroplaning. Only a safe
and attentive driver can prevent acci­dents. The capabilities of an ESP®­equipped vehicle must never be used
as a substitute for careful driving.
3-33
The ESP® has the following three systems:
Stability Control System The vehicle stability control system helps provide integrated control of systems such as anti-lock brakes, traction control, engine control, etc. This system automatically
controls the brakes and engine to help pre­
vent the vehicle from skidding when cor­
nering on a slippery road surface or when
turning the steering wheel abruptly.
Traction Control System The traction control system automatically
helps prevent the spinning of wheels when
the vehicle is started or accelerated on slippery road surfaces. The system oper­
ates only if it senses that some of the wheels are spinning or beginning to lose traction. When this happens, the system
operates the front or rear brakes and
reduces engine power to
limit wheel spin.
NOTE: You may hear a clicking sound in the
engine compartment for a few seconds when you start the engine or just after the
vehicle begins to move. This means that
the above systems are in the self-check mode. This sound does not indicate a mal­
function.
Anti-Lock Braking System (ABS) ABS will help you avoid skidding by elec­
tronically controlling braking pressure. It will also help you maintain steering control when braking on slippery surfaces or when
braking hard. The ABS works automati­cally, so you do not have to use any special braking technique. Just push the brake pedal down without pumping. The ABS will operate whenever it senses that wheels are locking up. You may feel the brake pedal pulsate while the ABS is operating.
(For more information on ABS, see "Brak­
ing" in the "OPERATING YOUR VEHICLE" section.)
NOTE: If the ABS system is activated, you may
hear a clunking noise and/or feel pulsating in the brake pedal. This is normal and indi­
cates that the brake fluid pressure is being
controffed properly