counter SUZUKI GRAND VITARA 2022 User Guide

7-46
INSPECTION AND MAINTENANCE
54P00-01E
Side turn signal light (if equipped)
64J195
Since the bulb is built-in type, replace it as
the light assembly. Remove the light
assembly by sliding the light housing left-
ward with your finger.
Front turn signal light and front position light
54P000710
(1) Front turn signal light
(2) Front position light
54P000711
1) Open the engine hood. To remove the
bulb holder of the front turn signal light
(1) or the front position light (2) from the
light housing, turn the holder counter-
clockwise and pull it out.
(1)(2)
(1) (2)

7-47
INSPECTION AND MAINTENANCE
54P00-01E
61MM0B078
(3) Removal
(4) Installation
2) To remove the bulb of the front turn sig-
nal light (1) from the bulb holder, push
in the bulb and turn it counterclockwise.
To install a new bulb, push it in and turn
it clockwise.
To remove and install the bulb of the
front position light (2), simply pull out or
push in the bulb.
Front fog light (if equipped)
1) Start the engine. Turn the steering
wheel to the opposite side of the fog
light to be replaced to replace the bulb
easily. Then turn off the engine.
54P000732
2) Remove the screws (1).
54P000712
3) Remove the clips (2) by prying them off
with a flat-bladed screwdriver as shown
in the illustration.
(2)
(1) (3)
(4)
EXAMPLE
(1)
EXAMPLE
(2)
EXAMPLE

7-51
INSPECTION AND MAINTENANCE
54P00-01E
54P000720
3) To remove the bulb holder of the rear
turn signal light (5) or the tail/brake light
(6) from the light housing, turn the
holder counterclockwise and pull it out.
54P000721
(7) Removal
(8) Installation
4) To remove the bulb of the rear turn sig-
nal light (5) or the tail/brake light (6)
from bulb holder, push in the bulb and
turn it counterclockwise. To install a
new bulb, push it in and turn it clock-
wise.
54P000722
NOTE:
When reinstalling the light housing, check
that the clips are properly attached.
(5)
(6)
(7)
(8)(5) / (6)
EXAMPLE

7-52
INSPECTION AND MAINTENANCE
54P00-01E
Reversing light
54P000723
1) Open the tailgate. Remove 15 clips (1),
and then pull out the trim (2).
54P000724
2) Disconnect the coupler (3) by pushing
the lock release. Turn the bulb holder of
the reversing light (4) counterclockwise
and remove it.
61MM0B090
(5) Removal
(6) Installation
3) To remove and install the bulb of the
reversing light (4), simply pull out or
push in the bulb.
License plate light
61MM0B086
1) Turn the cover (1) counterclockwise to
remove it.
(1)
(2)
(3)(4)
(4)
(5)
(6)
EXAMPLE
(1)

7-53
INSPECTION AND MAINTENANCE
54P00-01E
61MM0B087
2) To remove and install the bulb of the
license plate light (2), simply pull out or
push in the bulb.
Rear fog light (if equipped)
54P000725
1) Insert your hands from the back side of
the rear bumper. Remove 2 nuts (2)
that fix the light housing (1) in place.
54P000726
2) Remove the light housing (1) by push-
ing the bolts (3). To remove the bulb
holder of the rear fog light (4), turn the
holder counterclockwise and pull it out.
(2)
(2) (1)
(1) (4) (3)(3)

7-54
INSPECTION AND MAINTENANCE
54P00-01E
54P000727
(5) Removal
(6) Installation
3) To remove the bulb of the rear fog light
(4) from bulb holder, push in the bulb
and turn it counterclockwise. To install a
new bulb, push it in and turn it clock-
wise.
Interior light
Remove the lens by using a flat-bladed
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
Front (without overhead console)
61MM0A207
Front (with overhead console)
61MM0A129
Center (without sunroof)
60G115
(5)
(6)(4)
OPEN
PUSH
TILT
CLOSE

8-1
EMERGENCY SERVICE
54P00-01E
Tire changing tool
61MM0B100
(1) Jack
(2) Wheel brace
(3) Jack handle
The tire changing tools are stowed in the
luggage compartment.
Refer to “LUGGAGE COMPARTMENT” in
“ILLUSTRATED TABLE OF CONTENTS”
section.
80J048
To remove the spare tire (if equipped), turn
its bolt (1) counterclockwise and remove it.
Jacking instructions
75F062
1) Place the vehicle on level, hard ground.
2) Set the parking brake firmly and shift
into “R” (Reverse).
EXAMPLE
(3)
(2)
(1)
WA R N I N G
After using the tire changing tools,
stow them securely or they can
cause injury if an accident occurs.
CAUTION
The jack should be used only to
change wheels. It is important to read
the jacking instructions in this sec-
tion before attempting to use the
jack.
(1)
WA R N I N G
• Shift into “R” (Reverse) when you
jack up the vehicle.
• Never jack up the vehicle with the
transaxle in “N” (Neutral). Other-
wise, unstable jack may cause an
accident.

54P00-01E
No-Using Conditions
- When temperature under -40
.
- On miring or sand ground.
- On big gradient road.
-In extreme nature condition: rainstorm, typhoon, cyclone, snowstorm,thunder-storm, etc.
- Loading dangerous heavy, for instance: melted metal, acidity substance, radioactivity
substance or specially crisp goods.
-Contact with hood directly.
-Using on boat.
-The ground with difference in level.
Operation instructions
Whenever a wheel is changed, always remove any corrosion
that may be present on inside of wheel and wheel mounting
surface on vehicle.
Details:
Please operate according to the “operation instructions”.
Operate the jack on the level ground while checking the jack
and the load.
Mustn’t operate under raising load, unless the load is fastened
surely.
- Park the car on the flat, level ground and apply the brake
firmly.
- Set transmission in “reverse”(automatic transmission in
“park”).
- Turn on the hazard warning flasher.
- Remove jacking tools and spare tire from stowage area.
- Block front and rear of wheel diagonally opposite wheel
being removed before operating jack.
- Loosen, but do not remove wheel nuts by turning wrench counter clockwise.
- Raise jack until jack-head groove fits boss of frame see illustrations.
- Operate jack with slow, smooth motion, using jack handle.
- Raise vehicle so an inflated tire will just clear surface, remove nuts and wheel.
- Install wheel, then slightly tighten each nut, wheel must be seated on hub.
- Lower vehicle, and fully tighten wheel nuts in across-cross sequence by turning wrench
clockwise.
Maintenance
- Please prevent the JACK SCREW from accretion of dirt.
- Check the nameplate, keep the shape same as original.
- No-rejigger the jack’s construction privately.
- After any use, consult immediately your Suzuki Dealer or Service Partner for inspection
and maintenance of the jack.
- If the label (sticker) is damaged, please consult your Suzuki Dealer or Service Partner.
>ö>í>ï>÷>õ>ú>ó>Ì
>ü>û>õ>ú?>Ì
>ö>í>ï>÷>õ>ú>ó>Ì>ü>û>õ>ú?>Ì
>ö>í>ï>÷>Ì>ô>í>ú>ð>ø>ñ>Ì>î>í>þ>Ì>ö>í>ï>÷>Ì>ô>í>ú>ð>ø>ñ>Ì