odometer SUZUKI GRAND VITARA 2022 Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2022, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2022Pages: 482, PDF Size: 21 MB
Page 88 of 482
2-66
BEFORE DRIVING
54P00-01E
Information display
The information display is shown when the
ignition switch is in “ON” position or the
ignition mode is “ON”.
54P000231
(1) Information display
61MM0A158
(2) Indicator selector knob
(3) Trip meter selector knob
The information display shows the follow-
ing information.
Display (A)
Clock
Display (B)
Driving mode (for 4WD models)
Display (C)
Thermometer
Display (D)
Warning and indicator messages /
Fuel consumption / Driving range /
Average speed /
Oil life (for diesel engine models)Display (E)
Gearshift indicator
Display (F)
Trip meter
Display (G)
Odometer
54P000256
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, the
message shown in the above illustration
will appear on the display for several sec-
onds.
Some warning and indicator messages
may appear on the display when the igni-
tion switch is in “ACC” or “LOCK” position,
or the ignition mode is “ACC” or “LOCK”
(OFF).
(1)(A) (B) (C)
(D)
(E)
(F)
(G)
(3)
(2)
EXAMPLE
Page 93 of 482
2-71
BEFORE DRIVING
54P00-01E
Gearshift indicator
The display (E) shows the gearshift indica-
tor.
54P000232
Refer to “Gearshift indicator” in “OPERAT-
ING YOUR VEHICLE” section.
Trip meter
The display (F) shows the trip meter.
The trip meter can be used to measure the
distance traveled on short trips or between
fuel stops.
You can use trip meter A or trip meter B
independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (3) for
about 2 seconds when the display shows
the trip meter.
Odometer
The display (G) shows the odometer.
The odometer records the total distance
the vehicle has been driven.
Setting mode
When the ignition switch is in “ON” position
or the ignition mode is “ON” and the vehi-
cle is stationary, you can enter the setting
mode of the information display by pushing
and holding the indicator selector knob (2)
for more than 3 seconds.
• To select the setting that you want to
change, turn the indicator selector knob
(2) left or right.
• To change the setting, push the indicator
selector knob (2).
• To exit the setting mode, select “Back”
and push the indicator selector knob (2).
61MM0A161
NOTE:
The currently selected setting item is sur-
rounded by a frame.
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
Page 94 of 482
2-72
BEFORE DRIVING
54P00-01E
NOTE:
• If you push and hold the indicator selec-
tor knob (2) to enter the setting mode
when the display (D) shows average fuel
consumption or average speed, the
value will be reset simultaneously. If you
do not want to reset the value, push the
indicator selector knob quickly to switch
the indication of the display.
• If you turn the ignition switch, press the
engine switch or start to move the vehi-
cle when the display is in the setting
mode, the setting mode will be canceled
automatically.
Distance unit
(Odometer / trip meter distance unit set-
ting)
You can change the units in which odome-
ter / trip meter distance is displayed.
NOTE:
When you change the units in which odom-
eter / trip meter distance is displayed, the
trip meter will be reset automatically.
Fuel economy
(Fuel consumption unit setting)
You can change the units that fuel con-
sumption is displayed in.
Language
You can change the language of the infor-
mation display.Fuel reset (Average fuel consumption
reset setting)
You can change when the value of aver-
age fuel consumption is reset.
Temperature
(Temperature unit setting)
You can change the units that temperature
is displayed in.
NOTE:
When you change the units that tempera-
ture is displayed in, the automatic heating
and air conditioning system (if equipped)
temperature display units will be changed
automatically.
Set sensors
(Parking sensor setting) (if equipped)
The parking sensor can be switched
between the normal mode and trailer
mode.Clock setting
• To change the hour indication, turn the
indicator selector knob (2) left or right
repeatedly when the hour indication
appears as reversed color. To change
the hour indication quickly, turn and hold
the indicator selector knob (2). To set the
hour indication, push the indicator selec-
tor knob (2) and the minute indication
appears as reversed color.
• To change the minute indication, turn the
indicator selector knob (2) left or right
repeatedly when the minute indication
appears as reversed color. To change
the minute indication quickly, turn and
hold the indicator selector knob (2). To
set the minute indication, push the indi-
cator selector knob (2).
You can also switch the time indication
between 12-hour and 24-hour format.
NOTE:
When the clock on the information display
is set, the clock in the instrument panel (if
equipped) is set in accordance with the
time of the clock on the information display.
Page 121 of 482
2-99
BEFORE DRIVING
54P00-01E
Oil change request light(if equipped)
79JM007
Your vehicle has the oil life monitoring sys-
tem and related oil change request light
that alerts you to change the engine oil and
oil filter.
When this light comes on or blinks, change
engine oil and oil filter immediately.
For details on how to change the engine oil
and oil filter, refer to “Changing engine oil
and filter” in “INSPECTION AND MAINTE-
NANCE” section.
Gasoline engine model and diesel engine
model have different lighting methods for
oil change request light. Check an appro-
priate method from the following descrip-
tions, according to your vehicle model.
(For gasoline engine model)
This light comes on for several seconds
when the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON” so you
can check that light is working.If either of odometer reading or time is
reached to the value which is set by the
system, this light blinks when the ignition
switch or engine switch is in “ON” position.
In addition, the message is shown on the
information display to tell you it is neces-
sary to change the engine oil and oil filter.
When the engine oil and oil filter are
changed, and the oil life monitoring system
is reset, this light will go out.
Whenever the engine oil and oil filter are
changed, the light must be reset to monitor
the next oil change timing properly. The
light will go out after the reset. For the
resetting procedure, refer to “Information
display” in this section.
NOTE:
This light is used to facilitate the oil and oil
filter change according to the maintenance
schedule.(For diesel engine model)
This light comes on for several seconds
when the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON” so you
can check that light is working.
If this light blinks when the engine is run-
ning, you should change the engine oil and
oil filter immediately since the monitoring sys-
tem has calculated that oil life has been
diminished by a deterioration of engine oil.
When the engine oil and oil filter are
changed, and the oil life monitoring system
is reset, this light will go out.
NOTICE
Severe engine damage will result, if
you keep operating the engine after
this light comes on.
Change the engine oil and oil filter
immediately when the light blinks.
Page 341 of 482
7-3
INSPECTION AND MAINTENANCE
54P00-01E
How to understand each table
54P000750
(1) Model of vehicle
(2) Maintenance item
(3) Driving condition
Necessary maintenance operation and timing will vary depending on your driving condition.
Some items have two different conditions of “Normal” and “Severe”, which are defined as follows.
“Normal”: If driving is usually done under normal driving condition
“Severe”: If driving is usually done under severe driving condition
For details of each condition, refer to “Maintenance recommended under severe driving condition” in this section.
If this part is blank, there is no classification in driving conditions.
Forgasoline engine models
Select maintenance timing by mileage (odometer reading) or
whichever comes first.
km (×1000)20406080120miles (×1000)12.52537.55075months1224364872Engine and powertrainEngine accessory drive belt Adjustment, Replacement NormalR ISevereIRValve clearanceI
Exhaust system (except catalyst)I
Drive axle boots/Propeller shafts (4WD)I
Manual transaxle oil Genuine
“SUZUKI GEAR OIL 75W-80”NormalI
SevereIROther than
“SUZUKI GEAR OIL 75W-80”NormalRSevereRl a m r o N ) D W 4 ( l i o r e f s n a r TISevereIR
(2)(3) (4) (5)
(1)
(6)
EXAMPLE
Page 343 of 482
7-5
INSPECTION AND MAINTENANCE
54P00-01E
EU countries (except for Russia)
Recommended maintenance items by an authorized SUZUKI dealer or a qualified service technician
For gasoline engine models
Select maintenance timing by mileage (odometer reading) or months, which-
ever comes first.
km (×1000)20406080120160miles (×1000)12.52537.55075100months122436487296Engine and powertrain
Engine accessory drive belt Adjustment, Replacement NormalIRSevereIR
Valve clearanceI
Exhaust system (except catalyst)I
Drive axle boots / Propeller shafts (4WD)I
Manual transaxle oil Genuine
“SUZUKI GEAR OIL 75W-80”NormalIR
SevereIR
Other than
“SUZUKI GEAR OIL 75W-80”NormalRSevereR
Transfer oil (4WD) NormalIRSevereIR
Rear differential oil (4WD) NormalIRSevereIR
Fuel and emission control system
Fuel linesI
Fuel tankI
PCV valveI
Fuel evaporative emission control systemI
Page 344 of 482
7-6
INSPECTION AND MAINTENANCE
54P00-01E
NOTE:
*1:Clean more frequently if the air flow from the air conditioner decreases.
For gasoline engine models
Select maintenance timing by mileage (odometer reading) or months,
whichever comes first.
km (×1000)204060miles (×1000)12.52537.5months122436Brake
Brake discs and padsI
Brake hoses and pipesI
Brake fluid ReplacementR
Brake lever and cable Adjustment (1st 20000 km only)I
Chassis, body and others
Clutch (Pedal and fluid level)I
Wheel bearingsSevere onlyI
Suspension systemI
Steering systemI
Air conditioner filter element
(if equipped)
*1Inspection First time only NormalI
Second time and after NormalI
Replacement NormalR
Inspection or replacement
SevereIR
WA R N I N G
The shock absorbers are filled with high pressure gas. Never attempt to disassemble them or throw them into a fire. Avoid
storing them near a heater or heating device. When scrapping the absorber, the gas must be released from the absorber
safely. Ask your dealer for assistance.
Page 345 of 482
7-7
INSPECTION AND MAINTENANCE
54P00-01E
Items other than recommended maintenance by an authorized SUZUKI dealer or a qualified service technician
#1:For further details, refer to “Engine oil and filter” in this section.
#2:Perform the engine coolant level check under the daily inspection in “OPERATING YOUR VEHICLE” section.
If you use the engine coolant other than “SUZUKI LLC (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Standard (Green)”.
NOTE:
*1: Refer to “Oil change request light (if equipped)” in “BEFORE DRIVING” section.
For gasoline engine models
Select maintenance timing by mileage (odometer reading) or months,
whichever comes first.
km (×1000)7.51015204080160miles (×1000)4.6876.259.37512.52550100months612364896Engine and powertrain
Engine accessory
drive beltTension check NormalISevereI
Engine oil and engine
oil filter
*1ACEA Standards or
SUZUKI GENUINE OIL (#1)NormalRSevereR
Other than ACEA Standards or SUZUKI
GENUINE OIL (#1)NormalRSevereR
Engine coolant“SUZUKI LLC:
Super (Blue)” (#2) First time only R
Second time and afterR
“SUZUKI LLC: Standard (Green)”R
Page 346 of 482
7-8
INSPECTION AND MAINTENANCE
54P00-01E
#3: If you replace the spark plugs other than iridium plug, follow the schedule of nickel plug.
#4: Replace every 50000 km if the local law requires.
NOTE:
*2: Inspect more frequently if the vehicle is used under dusty conditions.
For gasoline engine models
Select maintenance timing by mileage (odometer reading) or months, which-
ever comes first.
km (×1000)2.510203040100miles (×1000)1.5626.2512.518.752562.5months-812243684Fuel and emission control system
Spark plugs when unleaded
fuel is used(Highly recommended) Iridium
plug (#3)NormalRSevereR
(Standard type) Nickel plug NormalR(#4)SevereR
Spark plugs when leaded fuel
is used(Highly recommended) Iridium
plug (#3)R
(Standard type) Nickel plugR
Air cleaner filter element *2 Paved-road NormalIR
SevereIR
Dusty conditionIRBrake
Brake fluid CheckI
Brake lever and cable Check (1st 20000 km only)I
Chassis, body and others
Tires/WheelsI
All latches, hinges and locksI
Page 347 of 482
7-9
INSPECTION AND MAINTENANCE
54P00-01E
Recommended maintenance items by an authorized SUZUKI dealer or a qualified service technician
For diesel engine models
Select maintenance timing by mileage (odometer reading) or months, which-
ever comes first.
km (×1000)204060-80140160miles (×1000)12.52537.5-5087.5100months1224-36486096Engine and powertrain
Engine accessory drive belt Ribbed belt NormalIRSevereIR
Camshaft timing belt NormalRSevereR
Exhaust system (except catalyst)I
Drive axle boots/Propeller shafts (4WD)I
Manual transaxle oil Genuine
“SUZUKI GEAR OIL 75W-80”NormalIR
SevereIR
Other than
“SUZUKI GEAR OIL 75W-80”NormalRSevereR
Transfer oil (4WD) NormalIRSevereIR
Rear differential oil (4WD) NormalIRSevereIR
Fuel and emission control system
Fuel linesI
Fuel filterR
Fuel tankI