inspection and maintenance SUZUKI IGNIS 2020 Repair Manual

7-47INSPECTION AND MAINTENANCE
75RM4-01E
NOTE:
Check that the fuse box always carries
spare fuses.
Fuses under dashboard
75RM299
80P0185
WA R N I N G
If the main fuse or a primary fuse
blows, have your vehicle inspected
by an authorized SUZUKI dealer.
Always use a genuine SUZUKI
replacement. Never use a substitute
such as a wire even for a temporary
repair, or extensive electrical damage
and a fire can result.
EXAMPLE
12 15
28
14
27
13
26 3
16
29 4
17
30 5
18
31 6
19
32 7
20
33 8
21
34 9
22
35 10
23
36 11
24
37 12
25
38
35,0Ν5Υа)86(
(1) 30 A Power window
(2) 10 A Meter
(3) 15 A Ignition coil
(4) 5 A Ignition-1 signal 2
(5) 20 A Shift lever
(6) – Blank
(7) – Blank
(8) 20 A Door lock
(9) 15 A Steering lock
(10) 10 A Hazard (11) 5 A A-STOP controller
(12) 10 A Rear fog lamp
(13) 5 A
ABS/ESP
® control module
(14) 15 A Seat heater
(15) 5 A Ignition-1 signal 3
(16) 10 A Dome light-2
(17) 5 A Dome light
(18) 15 A Radio
(19) 5 A CONT
(20) 5 A Key 2

7-48
INSPECTION AND MAINTENANCE
75RM4-01E
81A283
Headlight aimingSince special procedures are required, ask
your authorized SUZUKI dealer for this job.
(21) 20 A Power window timer
(22) 5 A Key
(23) 15 A Horn
(24) 5 A Tail light (Left)
(25) 10 A Tail light
(26) 10 A Air bag
(27) 10 A Ignition-1 signal
(28) 10 A Back-up light
(29) 5 A ACC-3
(30) 20 A Rear defogger
(31) 10 A Heated mirror
(32) 15 A ACC-2
(33) 5 A ACC
(34) 10 A Rear wiper
(35) 5 A Ignition-2 signal
(36) 15 A Washer
(37) 25 A Front wiper
(38) 10 A Stop light
WA R N I N G
Always replace a blown fuse with a
fuse of the correct amperage. Never
use a substitute such as aluminum
foil or wire to replace a blown fuse. If
you replace a fuse and the new one
blows in a short period of time, you
may have a major electrical problem.
Have your vehicle inspected immedi-
ately by your SUZUKI dealer.
BLOWN
OK

7-49INSPECTION AND MAINTENANCE
75RM4-01E
Bulb replacement
Interior lightRemove the lens by using a flat-bladed
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
Front
76MH0A139
Luggage compartmen t (if equipped)
81PN162
HeadlightsLED headlights (if equipped)
Since special procedures are required, we
recommend you take your vehicle to your
SUZUKI dealer for bulb replacement.
Halogen headlights (if equipped)
75RM067
1) Open the engine hood. Disconnect the
coupler (1). Remove the sealing rubber
(2).
CAUTION
• Light bulbs can be hot enough to burn your finger right after turning
off lights. This is true especially for
halogen headlight bulbs. Replace
the bulbs after they become cool
enough.
• The halogen headlight bulbs are filled with pressurized halogen gas.
They can burst and injure you if
they are hit or dropped. Handle
them carefully.
• To avoid injury by sharp-edged
parts of the body, wear gloves and
a long-sleeved shirt when replacing
light bulbs.
NOTICE
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
NOTICE
Frequent bulb replacement indicates
the need for an inspection of the elec-
trical system. This should be carried
out by your SUZUKI dealer.
(1)
(2)

7-50
INSPECTION AND MAINTENANCE
75RM4-01E
75RM068
2) Push the retaining spring (3) forwardand unhook it. Then remove the bulb.
Install a new bulb in the reverse order
of removal.
75RM069
NOTE:
You can see the position of retaining spring
from the hole (4) of headlight.
Side turn signal l ight (if equipped)
64J195
Since the bulb is built-in type, replace it as
the light assembly. Remove the light
assembly by sliding the light housing left-
ward with your finger.
(3)
(4)

7-51INSPECTION AND MAINTENANCE
75RM4-01E
Front fog light (if equipped)1) Start the engine. Turn the steeringwheel to the opposite side of the fog
light to be replaced to replace the bulb
easily. Then turn off the engine.
75RM094
2) Remove the clip (1) by prying it off witha flat-bladed screwdriver as shown in
the illustration.
80JM071
3) Open the end of the cover inside thefender. Disconnect the coupler by push-
ing the lock release. Turn the bulb
holder counterclockwise and remove it.
Daytime running light (if equipped)Models with LED headlights
Since special procedures are required, we
recommend you take your vehicle to your
SUZUKI dealer for bulb replacement.
Models with halogen headlights
1) Start the engine. Turn the steering
wheel to the opposite side of the fog
light to be replaced the bulb easily.
Then turn off the engine.
75RM094
2) Remove the clip (1) by prying it off witha flat-bladed screwdriver as shown in
the illustration.
(1)
EXAMPLE
(1F

7-52
INSPECTION AND MAINTENANCE
75RM4-01E
75RM244
3) Open the end of the cover inside thefender. Disconnect the coupler by push-
ing the lock release. Turn the bulb
holder counterclockwise and remove it.
Other general lightsBulb holder
54G123
(1) Removal
(2) Installation
To remove a bulb holder from a light hous-
ing, turn the holder counterclockwise and
pull it out. To install the holder, push the
holder in and turn it clockwise. Bulb
54G124
(3) Removal
(4) Installation
There are two types of bulb, full glass type
(1) and glass/metal type (2).
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and tu rn it clockwise.
You can access the individual bulb or bulb
holders as follows.
EXAMPLE
(1)
(1)
(2) (2)
EXAMPLE
(1)
(2)
(
3 )
(4)EXAMPLE

7-53INSPECTION AND MAINTENANCE
75RM4-01E
Front turn signal light (1)
Front position light (2)
Models with halogen headlights
75RM066
Models with LED headlights
62R0306
Rear combination light
75RM070
Remove the bolts (1) and pull the light
housing (2) straight.
NOTE:
When reinstalling the light housing, check
that the clips (3) are properly attached.Reversing light
62R0122
1) Open the tailgate and remove the trim
(1) of the tailgate.
• Insert a flat blade screwdriver cov-ered with a soft cloth between the trim
and the tailgate to make a space for
fingers, and then pull out the trim with
your fingers.
(1)(2)(1)
(3)
(2)
(1)
(1)

7-54
INSPECTION AND MAINTENANCE
75RM4-01E
62R0378
2) Disconnect the coupler (2) by pushingthe lock release. Turn the bulb holder of
the reversing light (3) counterclockwise
and remove it. License plate light
75RM071
Rear fog light (if equipped)
75RM072
1) Remove the clip (1) by prying it off with
a flat blade screwdriver as shown in the
illustration.
75RM073
2) Open the end of the cover inside thefender.
(2)
(3)
(1)

7-55INSPECTION AND MAINTENANCE
75RM4-01E
Wiper blades
54G129
If the wiper blades become brittle or dam-
aged, or make streaks when wiping,
replace the wiper blades.
To install new wiper blades, follow the pro-
cedures below.NOTE:
Some wiper blades may be different from
the ones described here depending on
vehicle specifications. If so, consult your
SUZUKI dealer for proper replacement
method.
For windshield wipers:
61MM0A208
1) Hold the wiper arm away from the win-
dow.
NOTE:
When raising both of the front wiper arms,
pull the driver’s side wiper arm up first.
When returning the wiper arms, lower the
passenger’s side wiper arm first.
Otherwise, the wiper arms may interfere
with each other.
61MM0A210
2) Open the lock (1), slide the wiper frame and remove it from the arm (2) as
shown.
61MM0A211
NOTICE
To avoid scratching or breaking the
window, do not let the wiper arm
strike the window while replacing the
wiper blade.
EXAMPLE
(1)
(2)
(;$03/((;$03/(

7-56
INSPECTION AND MAINTENANCE
75RM4-01E
3) Pull the locked end of the wiper bladefirmly to unlock the blade and slide the
blade out as shown.
71LMT0708
(3) Retainer
4) If the new blade is provided without the two metal retainers (3), move them
from the old blad e to the new one.
61MM0B098 61MM0A212
(A) Up
(B) Down
NOTE:
When you install the metal retainers (3),
make sure the direction of metal retainers
as shown in the above illustrations.
(3)
(3)
EXAMPLE
(3)
(3)
EXAMPLE
(3) (A)
(B)
EXAMPLE