ECO mode SUZUKI JIMNY 2019 Owners Manual

Vehicle Data Recordings
There are certain components of your vehicle (the "Vehicle") incorporating data storage modules or memories, which temporarily or per­manently store the technical data below listed. These data are exclusively technical and serve for (i) identifying and correcting faults occurred in the Vehicle and/or (ii) optimizing functions of the Vehicle.
Recorded data (the "Recorded Data") • Malfunctions, faults, and errors in important system components. (e.g. lights, brakes) Reactions of the Vehicle in certain situations (e.g. inflation of SRS airbags, activation of stability control system). Operating conditions of system components (e.g. filling levels). Status messages of the Vehicle and its individual components (e.g. vehicle speed, acceleration, deceleration, lateral acceleration). Ambient conditions (e.g. outside temperature).
Recorded data vary depending on vehicle model or grade.
(For EU countries)
Parties who can read out the technical data using specific diagnostic devices (the "Parties"); • Authorized distributors, dealers and repairers/service workshops of SUZUKI vehicles, and independent repairers/service workshops Manufacturer of SUZUKI vehicles (e.g. SUZUKI MOTOR CORPORATION ("SUZUKI"), Magyar Suzuki Corporation Ltd., • Maruti Suzuki India Limited, Suzuki Motor (Thailand) Co., Ltd., Thai Suzuki Motor Co., Ltd.) • Suppliers of SUZUKI vehicle parts, components and accessories (the "Suppliers")
Data usage (the "Data Usage") SUZUKI and the Parties may use the Recorded Data in the modules or memories for the purpose of: Diagnostic, service, repair and warranty processes Research and further vehicle developments • Implementation of or investigation for field actions including recall and service campaign • Quality improvements, etc.
After an error has been corrected, data related to such error are basically deleted from error storage module or memory, while certain data are overwritten or kept further.

Conditions under which SUZUKI and the Parties can disclose or provide any of the Recorded Data to a third party SUZUKI and the Parties may disclose or provide any of the Recorded Data to a third party under any of the following conditions: • A consent from the Vehicle owner/user(s), or from lessee of the Vehicle (in case of lease) is obtained. It is officially requested by police, prosecutor, court, or other authorities. · It is provided to a research institute for statistical study after processing in such a manner that owner/user(s) of the Vehicle cannot be
identified. It is used by SUZUKI or the Parties or their directors, officers or employees for the purposes described in the Data Usage. It is used by SUZUKI or the Parties in a lawsuit. Any other cases allowed by applicable laws and regulations. If required, you may receive further information from each of the Parties other than the Suppliers.
NOTE: The data cannot be used to detect the Vehicle's movements. The data stored in data storage modules or memories differ according to the Vehicle's grade or model. • No conversation nor noise/sound will be recorded in any event. • The data may not be recorded in some situations.
If these technical data are combined with other information (e.g. accident or witness report, damage on the Vehicle, etc.), there may be cases that such data may identify a specific person.
e-Call / ERA-GLONASS Functions added based on agreement with the customer may transmit certain vehicle data (e.g. vehicle location in emergency cases) from the Vehicle to police or emergency service official for the purpose of rescue or response to traffic accident.

FOR SAFE DRIVING
ELR type belt
80JC021
1-29
(For models with front passenger airbag deactivation system) Whenever possible, SUZUKI recom­mends that child restraint systems be installed on . th_e rear seat. According to· accident stat1st1cs, children are safer when ~roperly restrained in rear seating posi­tions than in front seating positions. • If you must install the child restraint sys­tem on the front passenger's seat follow instructions below. ' -D_eactivate the front passenger's front airbag by the front passenger airbag d~activation system (if equipped). -Slide the seat to the most rear position by the seat position adjustment lever. -If there is a gap or space between the child restraint and the seatback, adjust the seatback angle in order to install the child restraint system properly.
Install your child restraint system accord­ing to the instructions provided by the child restraint system manufacturer.
Check that the seat belt is securely latched. Move the child restraint system in all direc­tions to check that it is securely installed. When you put your child in the child restraint system, appropriately slide the front seat forward not to touch a part of your child's body.
Installation with ISOFIX type
anchorages
78RB02020
Your vehicle is equipped with the lower anchorages in the rear seat outboard seat­ing positions for securing a ISOFIX type of child restraints with the connecting bars. The lower anchorages are located where the rear of the seat cushion meets the bot­tom of the seatback.
A WARNING
Install the ISOFIX type of child restraint(s) in the only outboard seat­ing positions, not in the central posi­tion for the rear seat.

A WARNING
(Continued) For vehicles with side airbags, do not use non-genuine seat covers on the front seats, because non­genuine seat covers may obstruct the inflation of side airbags. Suzuki highly recommends Suzuki-genu­ine seat covers to be used when covering the front seats of such vehicles with side airbags. Also, near the door, do not place cup holders, hangers or any other objects and do not lean an umbrella, as these objects could be propelled by the airbag in the event of a collision. Either of these condi­tions may cause severe injury. Do not strike or apply significant levels of impact to the airbag com­ponent areas. It can cause the air­bags to malfunction.
Even though your vehicle is moderately damaged by a collision, it may not be severe enough to trigger front, side or side curtain airbags to inflate. If your vehicle sustains any front-end or side damage, have the airbag system inspected by a SUZUKI dealer to ensure that ii works properly.
Your vehicle is equipped with a diagnostic module which records information about the airbag system if the airbags deploy in a collision. The module records information about overall system status, and which sensors activated the deployment, and for a certain vehicle only, whether the driver's seat belt was in use.
Servicing the airbag system If the airbags inflate, have the airbags and related components replaced by a SUZUKI dealer as soon as possible.
If your vehicle ever gets in deep water and the driver's floor is submerged, the airbag controller could be damaged. If this hap­pens, ask a SUZUKI dealer to check the airbag system as soon as possible.
FOR SAFE DRIVING
Special procedures are required for servic­ing or replacing an airbag. For that reason, only a SUZUKI dealer should be allowed to service or replace your airbags. Remind anyone who services your SUZUKI vehicle that it has airbags.
Service on or around airbag components or wiring must be performed only by a SUZUKI dealer. Improper service could result in unintended airbag deployment or could render the airbag inoperative. Either of these two conditions may result in severe injury.
To prevent damage or unintended inflation of the airbag system, check that the lead­acid battery is disconnected and the igni­tion switch has been in "LOCK" position for at least 90 seconds before performing any electrical service work on your SUZUKI vehicle. Do not touch airbag system com­ponents or wires. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow for easy identification.
Scrapping a vehicle that has an uninflated airbag can be hazardous. Ask a SUZUKI dealer, body repair shop or scrap yard for help with disposal.
1-46

Keyless entry system
transmitter (if equipped)
(2)
79MH0237
(1) LOCK button (2) UNLOCK button
There are two ways to lock or unlock all doors (including the tailgate) simultane­ously by operating the transmitter near the vehicle.
Central door locking system To lock all doors, push LOCK button (1) once. • To unlock all door, push UNLOCK button (2) once.
NOTE: You can switch the function that unlocks all doors from requiring two pushes to requir­ing one push, and vice versa, via the infor­mation display setting mode. For details on how to use the information display, refer to "Information display" in this section.
The turn signal lights will flash once when the doors are locked.
When the doors are unlocked: The turn signal lights will flash twice. If the interior light switch is in DOOR position, the interior light will turn on for about 15 seconds and then fade out. If you insert the key into the ignition switch during this time, the light will start to fade out immediately.
Check that the doors are locked after you operate LOCK button (1 ).
NOTE: If no door is opened within about 30 sec­onds after UNLOCK button (2) is operated, the doors will automatically lock again.
BEFORE DRIVING
NOTE: The maximum operating distance of the keyless entry system transmitter is about 5 m (16 ft.), but this can vary depending on the surroundings, especially near other transmitting devices such as radio towers or CB (Citizen's Band) radios. The door locks cannot be operated with the transmitter, if the ignition key is inserted in the ignition switch. When any door is open, the door locks can only be unlocked with the transmit­ter, and the turn signal light will flash. If you lose one of the transmitters, ask a SUZUKI dealer as soon as possible for a replacement. Have a SUZUKI dealer program the new transmitter code in your vehicle's memory so that the old code is erased.
NOTICE
The transmitter is a sensitive elec­tronic instrument. To avoid damaging the transmitter: Do not expose it to impacts, mois­ture or high temperature such as by leaving it on the dashboard under direct sunlight. Keep the transmitter away from magnetic objects such as a televi­sion.
2-6

•
Turn the indicator selector knob (2).
c:::::> Push the indicator selector knob (2).
NOTE: Depending on vehicle's specifications, some items may not be displayed.
How to use the setting mode: 1) When the ignition switch is "ON" and the vehicle is stationary, push and hold the indicator selector knob (2) until the display shows "[Lo[H". 2) Turn and/or push the indicator selector knob (2) to select a function that you want to set up according to the chart in the previous page. 3) Turn and/or push the indicator selector knob (2) to register settings of the fol­lowing functions.
SEL I I Cl ::J 0 , -::JL C
68PM00272
NOTE: As shown in the above illustration, "SEL" indicates on the display of currently set­ting item. To go back to the higher level display during operation, turn the indicator selector knob (2) to display "bRCH" or " -bR C " and then push the indicator selector knob (2).
Time indication of clock "[L " • [L-t2h: 12-hourformat • CL -2'-lh: 24-hour format
NOTE: Default setting for time indication of clock varies according to the specification.
Additional flashes of the turn signal
"L2" • L2-5L 1: Turn signal flashes three times after the turn signal lever is returned (default set­ting) • L2-5L2: Disable the additional flashes of turn signal
Lighting time of the "To car" function 11 e, :" (if equipped) G t-SL :: Disable the "To car" function c; t-5L2: 10 seconds (default setting) G l-5L3: 15 seconds c; t-SL 'I: 20 seconds G t-5L5: 25 seconds
BEFORE DRIVING
Lighting time of the "To home" function "[,2 11 (if equipped) G2-5L :: Disable the "To home" func-tion C2-5L2: 10 seconds (default setting) G2-5L3: 15seconds G2-5L l/: 20 seconds G2-SLS: 25 seconds G2-5L5: 30 seconds
Tyre pressure monitoring system set­ting (if equipped) UnLRdn: Comfort Mode (default set-ting) • LRdEn : Load Mode
Refer to "Tyre pressure monitoring system (TPMS)" in "OPERATING YOUR VEHI­CLE" section for details.
Initialization setting "dE-a,," • dE-on: Initialize all settings
How to exit the setting mode: Switch the display to show "End" and then push the indicator selector knob (2).
2-24

BEFORE DRIVING
Display (E) Trip meter I Rear passenger's seat belt reminder (if equipped)
Display (F) Odometer
Display (G) Fuel gauge
52RS20420
When the ignition switch is turned "ON", the message shown in the above illustra­tion will appear on the display for several seconds. Some warning and indicator messages may appear on the display when the igni­tion switch is in "ACC" or "LOCK".
2-29
Clock
When the ignition switch is in "ON", the dis­
play (A) shows the time.
To set the clock, follow "Setting mode" instructions in this section.
,A WARNING
If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving.
Thermometer
When the ignition switch is "ON", the dis­play (B) shows the thermometer. The thermometer indicates the outside temperature.
-3°c
78RB02040
If the outside temperature nears freezing condition, the mark (a) will appear on the display.
NOTE: The outside temperature indication is not the actual outside temperature when driving at low speed, or when stopped. If there is something wrong with the ther­mometer, or just after the ignition switch is turned "ON", the display may not indi­cate the outside temperature.
When the display (C) shows the driving range, you can change the unit of tem­perature. To change the unit of temperature, refer to "Setting mode" in this section.
25°(
77 °F
(Initial setting)
52RM20880

BEFORE DRIVING
Instantaneous fuel consumption The display shows instantaneous fuel con­sumption with a bar graph only when the vehicle is moving.
NOTE: The display does not show the bar graph unless the vehicle is moving. Depending on the vehicle's specification, the fuel consumption units of initial set­ting are indicated as U100km, km/L or MPG (UK). The indicated maximum value of instan­taneous fuel consumption is one of the followings. No more than the maximum value will be indicated on the display even if the actual instantaneous fuel consumption is higher. -For U100km setting: 30 -For km/L setting: 50 -For MPG (UK) setting: 80 The indication on the display may be delayed if fuel consumption is greatly affected by driving conditions. The display shows estimated values. Indications may not be the same as actual values.
2-31
Average fuel consumption If you previously selected average fuel consumption setting, the display shows average fuel consumption from the last reset to the present when the ignition switch is turned "ON".
NOTE: When you reconnect the terminals to the lead-acid battery, the value of average fuel consumption will be shown after driving for a period of time.
You can select the timing to reset the value of average fuel consumption by one of the following three methods; Reset after refuel: the value of average fuel consumption will be reset automati­cally by refueling. Reset with trip meter A: the value of average fuel consumption will be reset automatically by resetting trip meter A. Reset manually: the value of average fuel consumption will be reset by push­ing and holding the indicator selector knob (3) when the display indicates the average fuel consumption.
To change the timing to reset the value of average fuel consumption, refer to "Setting mode" in this section.
NOTE: If you add only a small amount of fuel when you select "Reset after refuel", the average fuel consumption value may not be reset.
Driving range If you selected driving range the last time you drove the vehicle, the display indicates "---" for a few seconds and then indicates the current driving range when the ignition switch is turned "ON".
The driving range shown in the display is the approximate distance you can drive until the fuel gauge indicates "E", based on current driving conditions.
When the low fuel warning light comes on, the display "---" will appear.
If the low fuel warning light comes on, fill the fuel tank immediately regardless of the value of driving range shown in the display.
When you refuel, the driving range is updated. However, if you only add a small amount of fuel, the correct value will not be displayed.

BEFORE DRIVING
Setting mode
When the ignition switch is "ON" and the vehicle is stationary, you can enter the set­ting mode of the information display by pushing and holding the indicator selector knob (3) for a while.
To select the setting that you want to change, turn the indicator selector knob (3) left or right. To change the setting, push the indicator selector knob (3). To exit the setting mode, select "Back" and push the indicator selector knob (3).
78RB02096
NOTE: The currently selected setting item is sur­rounded by a frame.
2-33
NOTE: If you push and hold the indicator selec­tor knob (3) to enter the setting mode when the display (CJ shows average fuel consumption or average speed, driving time, the value will be reset simultane­ously. If you do not want to reset the value, push the indicator selector knob quickly to switch the indication of the dis­play. If you turn the ignition switch or start to move the vehicle when the display is in the setting mode, the setting mode will be canceled automatically.
Distance unit (Odometer I trip meter I driving range I average speed distance unit setting) You can change the units in which odome­ter I trip meter I driving range I average speed distance is displayed.
Fuel economy (Fuel consumption unit setting) You can change the units that fuel con­sumption is displayed in.
Language You can change the language of the infor­mation display.
Fuel reset (Average fuel consumption reset setting) You can change when the value of aver­age fuel consumption is reset.
Temperature (Temperature unit setting) You can change the units that temperature is displayed in. To change the temperature unit, select "Temperature" in "Setting mode". Then, select "°C" or "°F".
NOTE: When you change the units that tempera­ture is displayed in, the automatic heating and air conditioning system temperature display units will be changed automatically.
Clock setting (Adjusting the clock) • Adjust the clock by selecting "Clock set­ting" in "Setting mode". Then, select "Adjust clock". To change the hour indication, turn the indicator selector knob (3) left or right repeatedly when the hour indication appears as reversed color. To change the hour indication quickly, turn and hold indicator selector knob (3). To set the hour indication, push the indicator selec­tor knob (3) and the minute indication appears as reversed color. To change the minute indication, turn the indicator selector knob (3) left or right repeatedly when the minute indication appears as reversed color. To change the minute indication quickly, turn and hold indicator selector knob (3). To set the minute indication, push the indicator selector knob (3).

(Selecting 12H/24H format) Switch the time indication between 12-hour and 24-hour format by selecting "Clock setting" in "Setting mode". Then, select "12H" or "24H".
Door lock (Door unlock setting) You can choose either once or twice oper­ation(s) to unlock all doors (including the tailgate) by turning the key or operating the keyless entry system transmitter.
You can also turn off or on the buzzer sound when the door(s) is (are) locked or unlocked.
Lights (Lane change setting) The turn signal and its indicator can be set whether they flash three times even if you return the turn signal control lever shortly after operating it. To change the lane change setting, select "Lane change" in "Setting mode". Then, select "ON" or "OFF" If you want to change the number of flashing, consult a SUZUKI dealer.
Guide me light setting (Light setting) (if equipped) You can change the lighting time of "To car" function or "To home" function.
Oil change (Oil life monitoring system reset setting) (if equipped) The oil life monitoring system must be reset after changing the engine oil and oil filter. To reset the system, push and hold the indicator selector knob (3) for a while.
TPMS (Tyre pressure monitoring system set­ting) (if equipped) You can check the current tyre pressure on the information display. You can set one of the initial values of tyre pressure below that are indicated on the tyre information label. -Comfort Mode -Load Mode
Refer to "Tyre pressure monitoring system (TPMS)" in the "OPERATING YOUR VEHI­CLE" section for details.
Traffic sign recognition (Traffic sign recognition setting) (if equipped) If you select "ON" the traffic sign recogni­tion function can be activated.
Refer to "Traffic sign recognition" in the "OPERATING YOUR VEHICLE" section for details.
BEFORE DRIVING
Default (Initialization setting) If you select "YES" and push the indicator selector knob (3), all settings will be reini­tialized.
2-34