AC CON SUZUKI JIMNY 2020 Owner's Manual

FOR SAFE DRIVING
60A039
To unfasten the seat belt, push the red "PRESS" button on the buckle and retract the belt slowly while holding the belt or/and the latch plate.
1-11
Lap-shoulder belt with detachable
connector (if equipped)
The rear lap-shoulder belt has a buckle, a latch plate and a detachable connector. The rear seat belt buckle and the connec­tor are designed so as not to allow a wrong latch plate to be inserted.
When the rear seatback is in the upright position, keep the detachable connector latched. Only when the rear seatback is folded down, unlatch the detachable con­nector. To latch and unlatch the connector, refer to "Unlatching and latching detach­able connector" in this section.
78RB02015
Fastening Before fastening the rear lap-shoulder belt, check the following precautions. The detachable connector (1) is securely
latched. The webbing is not twisted. The rear lap-shoulder belt is not put through the seat belt hanger.
To fasten the belt, sit up straight and far back into the seat, pull the latch plate (2) across your body and press it straight into the buckle (3) until you hear a click.

FOR SAFE DRIVING
A WARNING
To minimize risk of severe injury or death in the event of a collision, always fasten seat belt with both latches buckled.
1-13
Unlatching and latching detachable connector
Unlatching To unlatch the connector: 1) Insert a key into the slot (1) on the con­nector and allow the belt to retract. 2) Once the belt has completely retracted. stow the belt in the holder. Refer to "Stowing rear lap-shoulder belt"" for
details in this section.
Latching To latch the connector: 1) Pull the belt out from the holder.
78RB02017
2) Insert the connector latch plate (2) into the connector (3).
A WARNING
Check that the detachable connector is securely latched and the webbing is not twisted.

Driver's seat belt reminder If the driver's seat belt remains unbuckled when the ignition switch is turned to "ON" position, the reminder works as follows: 1) The driver's seat belt reminder light will come on. The front passenger's seat
belt reminder light will also come on if a front passenger does not fasten his/her seat belt. 2) After the vehicle's speed has reached about 15 km/h, the driver's seat belt reminder light will blink and a buzzer will sound for about 95 seconds. 3) The reminder light will remain on until the driver's seat belt is buckled. If the driver has buckled his or her seat belt and later unbuckles the seat belt, the reminder system will be activated from Step 1) or 2) according to the vehicle's speed. When the vehicle's speed is less than 15 km/h, the reminder will start from Step 1 ). When the vehicle's speed is more than 15 km/h, the reminder will start from Step 2). The reminder will be automatically can­celed when the driver's seat belt is buckled or the ignition switch is turned off.
Front passenger's seat belt reminder (if equipped) If there is a person sitting in the front pas­senger seat and the front passenger seat belt is unbuckled when the ignition switch is turned to "ON" position, the front pas­senger's seat belt reminder will activate. The front passenger's seat belt reminder works in the same manner as the driver's seat belt reminder.
NOTICE
The sensor of the front passenger's
seat belt reminder is located in the seat cushion. Therefore, if you spill liquid such as liquid aromatics1 soft drinks or juice on the front passen­ger's seat cushion, immediately wipe it dry with a soft cloth. Otherwise, the sensor of the front passenger's seat belt reminder can be damaged.
NOTE: If you put an object on the passenger's seat, the weight of the object will be sensed by the sensor and the front pas­senger's seat belt reminder light (if
equipped) will come on and then the interior buzzer may beep. ff a child or a sma/1 sized person sit on the front passenger's seat or the cushion is put on the front passenger's seat, the weight wi/1 not be sensed by the sensor and the interior buzzer may not beep.
FOR SAFE DRIVING
Rear passenger's seat belt reminder (if equipped) If there is a person sitting in the rear pas­senger seat and the rear passenger seat belt is unbuckled when the ignition switch is turned to "ON" position, the rear passen­ger's seat belt reminder will activate. The rear passenger's seat belt reminder works in the same manner as the driver's seat belt reminder.
NOTICE
The sensor of the rear passenger's seat belt reminder is located in the seat cushion. Therefore, if you spill liquid such as liquid aromatics, soft drinks or juice on the rear passen­ger's seat cushion, immediately wipe it dry with a soft cloth. Otherwise, the sensor of the rear passenger's seat belt reminder can be damaged.
NOTE: ff you put an object on the rear passen­ger's seat, the weight of the object will be sensed by the sensor and the rear pas­senger's seat belt reminder light (if equipped} wi/1 come on and then the interior buzzer may beep. ff a child or a small sized person sit on the rear passenger's seat or the cushion is put on the rear passenger's seat, the weight will not be sensed by the sensor and the interior buzzer may not beep.
1-16

FOR SAFE DRIVING
Seat belt hanger
NOTICE
When you move a seatback, make sure the belt webbing is hooked in the seat belt hangers so the seat belts are not caught by the seatback, seat hinge, or seat latch. This helps prevent damage to the belt system.
1-17
Seat belt inspection
65D209S
Periodically check if the seat belts work properly and are not damaged. Check the webbing, buckles, latch plates, retractors, anchorages and guide loops. Replace any seat belts which do not work properly ·or
are damaged.
A WARNING
Inspect all seat belt assemblies after any collision. Any seat belt assembly which was in use during a collision (other than a very minor one) should be replaced, even if damage to the assembly is not obvious. Any seat belt assembly which was not in use during a collision must be replaced if the airbags and the seat belt preten­sioners activated. The airbags, the pretensioners and the load limitter will only function once. In case they did not activate, consult with Suzuki dealer.

FOR SAFE DRIVING
Detailed information for child restraint system (for the vehicle with airbag deactivation switch)
Seating position
Seat position number
Seating position suitable for universal belted (YES/NO)
i-Size seating position (YES/NO)
Seating position suitable for lateral fixture (L 1/L2)
Suitable rear-facing fixture (R1/R2/R3)
Suitable front-facing fixture (F2X/F2/F3)
Key of letters to be inserted in the above table YES =Suitable for this seating position NO = Not suitable for this seating position
Front Passenger airbag is activated
NO
NO
NO
NO
NO
X =ISOFIX position is not suitable for ISOFIX child restraint systems in this fixture.
G)
ISOFIX child restraint systems are divided into different mass group, size class and fixture.
Front Passenger airbag is deactivated
YES
NO
NO
NO
NO
The child restraint system can be used in the seating positions for fixture shown in the above table. For mass group, size class and fixture, confirm the table of next page.
NOTE:
(2)
YES
YES
X
R1, R2
F2X, F2, F3
@
YES
YES·
X
R1, R2
F2X, F2, F3
For the Installation suitability of child restraint systems of Taiwan models, refer to "For Taiwan" in the "SUPPLEMENT' section.
1-21

FOR SAFE DRIVING
Detailed information for child restraint system (for the vehicle without airbag deactivation switch)
Seat position number
Seating position suitable for universal belted (YES/NO)
· i-Size seating position (YES/NO)
Seating position suitable for lateral fixture (L 1 /L2)
Suitable rear-facing fixture (R1/R2/R3)
Suitable front-facing fixture (F2X/F2/F3)
Key of letters to be inserted in the above table YES =Suitable for this seating position NO = Not suitable for this seating position X =ISOFIX position is not suitable for ISOFIX child restraint systems in this fixture.
CD
YES (#1)
NO
NO
NO
NO
ISOFIX child restraint systems are divided into different mass group, size class and fixture. The child restraint system can be used in the seating positions for fixture shown in the above table. For mass group, size class and fixture, confirm the table of next page.
#1: When installing the child restraint systems, only a front-facing fixture is suitable.
1-25
Seating position
@
YES
YES
X
R1, R2
F2X, F2, F3
@
YES
YES
X
R1, R2
F2X, F2, F3

Approval mark to meet child
restraint system regulation for UN
R44 / R129 regulation
The following mark is shown on the child restraint system to meet the regulation of UN R44 / R129 for the child restraint sys­tem.
ECE R44/04 (1) ECE R129
Universal (2) i-Size
(3) -18kg Y (5) 40cm • 70cm I:!. 24kg (4)
@ (6) @
******** (7) ********
78RB01010
(1) Regulation number (2) Suitability for child restraint system category (3) Weight range of the applicable child who is applicable for this approval mark as shown in the mark (4) Height range and weight range of the applicable child who is applicable for this approval mark in the mark (5) Specification of appliance (6) Country code which approved child restraint system
(7) Approval number of child restraint seat
This approval mark is a representative example.
NOTE: UN R44 I R129 means the international regulation for the child restraint system. "EGE" is shown on the mark in the illus­tration for the child restraint system. This "EGE" mark is the same as "UN".
FOR SAFE DRIVING
Installation with lap-shoulder seat belts
A CAUTION
If your vehicle is equipped with the head restraint, adjust the height of the head restraint or remove it for fit­ting the child restraint, as necessary. However, if a booster cushion not equipped with the head restraint is fitted, the head restraint should not be removed. If the head restraint is removed for fitting the child restraint, you need to install it again after removing the child restraint. If the child restraint is fitted improp­erly, a child sitting in it could be injured in a collision.
NOTE: Stow the removed head restraint in the lug­gage compartment so it will not cause inconvenience to the occupants.
1-28

FOR SAFE DRIVING
ELR type belt
80JC021
1-29
(For models with front passenger airbag deactivation system) Whenever possible, SUZUKI recom­mends that child restraint systems be installed on . th_e rear seat. According to· accident stat1st1cs, children are safer when ~roperly restrained in rear seating posi­tions than in front seating positions. • If you must install the child restraint sys­tem on the front passenger's seat follow instructions below. ' -D_eactivate the front passenger's front airbag by the front passenger airbag d~activation system (if equipped). -Slide the seat to the most rear position by the seat position adjustment lever. -If there is a gap or space between the child restraint and the seatback, adjust the seatback angle in order to install the child restraint system properly.
Install your child restraint system accord­ing to the instructions provided by the child restraint system manufacturer.
Check that the seat belt is securely latched. Move the child restraint system in all direc­tions to check that it is securely installed. When you put your child in the child restraint system, appropriately slide the front seat forward not to touch a part of your child's body.
Installation with ISOFIX type
anchorages
78RB02020
Your vehicle is equipped with the lower anchorages in the rear seat outboard seat­ing positions for securing a ISOFIX type of child restraints with the connecting bars. The lower anchorages are located where the rear of the seat cushion meets the bot­tom of the seatback.
A WARNING
Install the ISOFIX type of child restraint(s) in the only outboard seat­ing positions, not in the central posi­tion for the rear seat.

Install the ISOFIX type child restraint sys­tem according to the instructions provided by the child restraint system manufacturer. After installation, try moving the child restraint system in all directions especially forward to check that connecting bars are securely latched to the anchorages.
84MM00252
Your vehicle is equipped with the top tether anchorages. Use the top tether strap of the child restraint according to the instructions provided by the child restraint system man­ufacturer.
Here is a general instruction:
A CAUTION
If your vehicle is equipped with the head restraint, adjust the height of the rear head restraint or remove it for fitting the child restraint, as nec­essary. However, if a booster cushion not equipped with the head restraint is fitted, the head restraint should not be removed. If the head restraint is removed for fitting the child restraint, you need to install it again after removing the child restraint. If the child restraint is fitted improp­erly, a child sitting in it could be injured in a collision.
NOTE: Stow the removed head restraint in the lug­gage comparlment so it will not cause inconvenience to the occupants.
FOR SAFE DRIVING
it'---â–º
78F114
1) Place the child restraint in the rear seat, inserting the connecting bars to the anchorages between the seat cushion and the seatback.
1-30

FOR SAFE DRIVING
68LM268
2) Use your hands to carefully align the connecting bar tips with the anchor­ages. Take care not to pinch your fin­gers.
1-31
54G184
3) Push the child restraint toward the anchor­ages so that the connecting bar tips are partially hooked to the anchorages. Use your hands to confirm the position.
54G185
4) Grasp the front of the child restraint and push the child restraint forcefully to latch the connecting bars. Check that they are securely latched by trying to move the child restraint system in all directions, especially forward. 5) Attach the top tether strap referring to "Installation of child restraint with top tether" section. When you put your child in the child restraint system, appropriately slide the front seat forward not to touch a part of your child's body.
NOTICE
When installing a child restraint sys­tem to the rear seat, adjust the front seat position so that the front seat does not interfere with the child restraint system.