sas SUZUKI JIMNY 2020 Owners Manual

A WARNING
Do not modify, remove, disassemble seat belts. Doing so may prevent them from functioning properly and cause the risk of severe injury or death in the event of a collision.
A WARNING
Never allow persons to ride in the cargo area of a vehicle. In the event of an accident, there is a much greater risk of injury for persons who are not riding in a seat with their seat belt securely fastened. Seat belts should always be adjusted as follows: -the lap portion of the belt should be worn low across the pelvis, not across the waist. -the shoulder straps should be worn on the outside shoulder only, and never under the arm. -the shoulder straps should be away from your face and neck, but not falling off your shoulder. (Continued)
FOR SAFE DRIVING
65D201
A WARNING
(Continued) • Seat belts should never be worn with the straps twisted and should be adjusted as tightly as is com­fortable to provide the protection for which they have been designed. A slack belt will provide less pro­tection than a snug belt. Check that each seat belt latch plate (tongue) is inserted into the proper buckle catch. It is possible to cross the buckles in the rear seat. (Continued)
1-8

A WARNING
(Continued) -Do not remove or disassemble the dual sensor. -Do not stick or affix anything to the lens of the dual sensor, not even clear items. • When the windshield around the dual sensor is deformed or dam­aged, or the windshield in front of the dual sensor is cracked because of an accident, the dual sensor can­not detect an obstacle in front of you, a pedestrian, an object of the high beam assist (such as the lights of the vehicle in front of you, street lamps, etc.), partition lines or traffic signs properly. If driving with these damaged parts, the dual sen­sor brake support will not function properly and unexpected accidents may occur. Operate the dual sensor brake support OFF switch to turn off the dual sensor brake support, and ask a SUZUKI dealer to have them inspected. (Continued)
A WARNING
(Continued) Do not apply any accessories (other than SUZUKI genuine acces­sories), films or stickers to the area listed below. These may affect with visibility of the dual sensor. If the area of the dual sensor is obstructed, the dual sensor cannot detect any vehicles, pedestrians, objects of the high beam assist (such as the lights of the vehicle in front of you, street lamps, etc.), partition lines or traffic signs prop­erly and the dual sensor brake sup­port may not function properly. Also, if applying them to an area other than the prohibited area, it may affect with the function of the dual sensor by reflection of light or an image. In this case, move them to another place. -On windshield
OPERATING YOUR VEHICLE
A WARNING
Do not remove or disassemble laser sensor parts of dual sensor. Do not look into irradiation portion of dual sensor by using the optical instrument such as magnifying glass, the objective glass, etc at distance within 10 cm (3.9 inch) from dual sensor when the ignition switch is turned to "ON". Your eyes might be damaged by laser.
3-44

Safety information
,A WARNING
If you pay too much attention to operating the audio system or view­ing the audio system display while driving, an accident can occur. If you set the sound volume too loud, it could prevent you from being aware of road and traffic conditions. • Keep your eyes on the road and your mind on the drive. Avoid pay­ing too much attention to operat­ing the audio system or viewing the audio system display. Familiarize yourself with the audio system controls and operation of the audio system before driving. • Preset your favorite radio stations before driving so that you can quickly tune to them using the presets. Set the sound volume to a level that will allow you to continue to be aware of road and traffic condi­tions while driving.
OTHER CONTROLS AND EQUIPMENT
Notes on discs
Precautions
When the inside of the vehicle is very
cold and the player is used soon after
switching on the heater, condensation
may form on the disc or the optical
parts of the player and proper playback
may not be possible. If condensation
forms on the disc, wipe it off with a soft
cloth. If condensation forms on the opti­
cal parts of the player, do not use the
player for about one hour. This will
allow the condensation to disappear
normally.
Driving on extremely bumpy roads
which cause severe vibrations may
cause sound to skip.
This unit uses a precision mechanism.
Even in the event that trouble arises,
never open the case, disassemble the
unit, or lubricate the rotating parts.
Bring the unit to a SUZUKI dealer.
Cautions on handling
[rr]oiL DIGITAL AUDIO (A)
52D274
This unit has been designed specifically for
playback of compact discs bearing mark
(A) shown above.
No other discs can be played.
5-32

INSPECTION AND MAINTENANCE
Interval: This interval should be judged byI km (x1000)I 15 I 30 I 45 I 60 I 75 90 odometer reading or months, whichever, miles (x1000)I 9 I 18 I 27 I 36 I 45 54 comes first. 1 monthsI 12 I 24 I 36 I 48 I 60 I 72 BRAKE *5-1. Brake discs and pads (front) I I I I I I Brake drums and shoes (rear) -I -I -I *5-2. Brake hoses and pipes -I -I -I 5-3. Brake fluid (#2) Check, *Replacement -R -R -R *5-4. Brake (Pedal and fluid level) I I I I I I 5-5. Brake lever and cable Check, *Adjustment (1st 15000 km only) I -----CHASSIS AND BODY *6-1. Clutch fluid (#2) -R -R -R *6-2. Clutch (pedal and fluid level) I I I I I I 6-3. Tyres/Wheels I I I I I I *6-4. Wheel bearings -I -I -I *6-5. Propeller shafts --I --I *6-6. Suspension system -I -I -I "6-7. Steering system -I -I -I *6-8. Manual transmission oil Genuine "SUZUKI GEAR OIL 75W" Inspect every 30000 km (18000 miles) or 24 months. Other than "SUZUKI GEAR OIL 75W" (1: 1st 15000 km only) I
I -I
R
I
-
I
-
I
R 6-9. Automatic transmission Fluid level -I -I -I *Fluid change Replace every 165000 km (99000 miles). *Fluid hose -I -I -I I I -I -*6-10. Transfer oil Genuine "SUZUKI GEAR OIL 75W" Inspect every 30000 km (18000 miles) or 24 months. Other than "SUZUKI GEAR OIL 75W" (I: 1st 15000 km only) I -R --R *6-11. Differential oil (R: 1 st 15000 km only) Genuine "SUZUKI SUPER GEAR OIL 75W-85 SYNTHETIC" R -I -I -
6-12. All latches, hinges and locks -I -I -I *6-13. Air conditioner filter element -I R -I R
#2: Clutch fluid is supplied from brake fluid reservoir.
A WARNING
The shock absorbers are filled with high pressure gas. Never attempt to disassemble them or throw them into a fire. Avoid storing them near a heater or heating device. When scrapping the absorber, the gas must be released from the absorber safely. Ask your dealer for assistance.
6-6

INSPECTION AND MAINTENANCE
Interval: This interval should be judged by1l--------------------=cic-c+T.C~~,'-,--+----,i'--+ odometer reading or months, whicheverI km (x1000) 7.5 I 15 I 22.5 I 30 I 37.5 45 miles (x1000) 4.5 I 9 I 13.5 I 18 I 22.5 27 comes first. 11-------------------~='---'c=cc=l-";c--+----.,,-+ months 6 I 12 I 18 I 24 I 30 36 BRAKE *5-1. Brake discs and pads (front) Brake drums and shoes (rear) *5-2. Brake hoses and pipes 5-3. Brake fluid (#2) *5-4. Brake (Pedal and fluid level) 5-5. Brake lever and cable CHASSIS AND BODY "6-1. Clutch fluid (#2) *6-2. Clutch (pedal and fluid level) 6-3. Tyres/Wheels *6-4. Wheel bearings *6-5. Propeller shafts *6-6. Suspension system *6-7. Steering system *6-8. Manual transmission oil
6-9. Automatic transmission
*6-10. Transfer oil
*6-11. Differential oil 6-12. All latches, hinges and locks *6-13. Air conditioner filter element •3
Genuine "SUZUKI GEAR OIL 75W"
Other than "SUZUKI GEAR OIL 75W"
Genuine "SUZUKI GEAR OIL 75W"
Other than "SUZUKI GEAR OIL 75W"
Check, *Replacement
Check, *Adjustment (1st 15000 km only)
Flu!d level *Fluid change
*Fluid hose
Genuine "SUZUKI SUPER GEAR OIL 75W-85 SYNTHETIC"
#2: Clutch fiuid is supplied from brake fiuid reservoir
A WARNING
-I -I -I ---I -----I -----R ---I -I -I -I ----
---R ---I -I -I -I -I -I -I -I -I -I -I -I ---I --· ---I --Inspect every 30000 km (18000 miles) or 24 months. Replace every 60000 km (36000 miles) or 48 months.
= I = I = I 7 I = I = Replace every 30000 km (18000 miles) or 24 months. Inspect every 60000 km (36000 miles) or 48 months. Inspect every 30000 km (18000 miles) or 24 months. Replace every 60000 km (36000 m!les) or 48 months. ---R --R R
R
The shock absorbers are filled with high pressure gas. Never attempt to disassemble them or throw them into a fire. Avoid storing them near a heater or heating device. When scrapping the absorber, the gas must be released from the absorber safely. Ask your dealer for assistance.
6-11

INSPECTION AND MAINTENANCE
Interval: This interval should be judged bylf---------------------a"'-<"~ccfl---c~+--,;;;.-+~ odometer reading or months, whichever1 km (x1000)I 20 I 40 I 60 I 80 I 100 I 120 miles (x1000)I 12.5 I 25 I 37.5 I 50 I 62.5 I 75 comes first. If-----------------------"='-"'-'-=-;?l----'-~+---:a,;-+~ months! 12 24 I 36 I 48 I 60 I 72
EMISSION CONTROL SYSTEM •4-1. PCV valve •4-2. Fuel evaporative emission control system BRAKE *5-1. Brake discs and pads (front) Brake drums and shoes (rear) *5-2. Brake hoses and pipes 5-3. Brake fluid (#3) *5-4. Brake (Pedal and fluid level) 5-5. Brake lever and cable CHASSIS AND BODY *6-1. Clutch fluid (#3) *6-2. Clutch (Pedal and fluid level) 6-3. Tyres/Wheels *6-4. Wheel bearings •6-5. Propeller shafts *6-6. Suspension system *6-7. Steering system *6-8. Manual transmission oil
*6-9. Automatic transmission oil
*6-10. Transfer oil
*6-11. Differential oil 6-12. All latches, hinges and locks *6-13. Air conditioner filter element
Check, *Replacement
Check, *Adjustment (1st 20000 km only)
Genuine "SUZUKI GEAR OIL 75W" Other than "SUZUKI GEAR OIL 75W" Fluid level *Fluid change *Fluid hose Genuine "SUZUKI GEAR OIL 75W" Other than "SUZUKI GEAR OIL 75W" Genuine "SUZUKI SUPER GEAR OIL 75W-85 SYNTHETIC"
#3: Clutch fluid is supplied from brake fluid reservoir.
A WARNING
I
-I -I -I I I -I ------I
I I I I I I -I -I -I -I -I -I -R -R -R I I I I I I I -----
-R -R -R I I I I I I I I I I I I
-I -I -I -I -I -I -I -I -I -I -I -I Inspect every 40000 km (25000 miles) or 24 months.
= I 7 I = I 7 I = I 7 Replace every 165000 km (99000 miles). -I -I I I -I -I I Inspect every 40000 km (25000 miles) or 24 months. -R -R -R R
R I R
The shock absorbers are filled with high pressure gas. Never attempt to disassemble them or throw them into a fire. Avoid storing them near a heater or heating device. When scrapping the absorber, the gas must be released from the absorber
safely. Ask your dealer for assistance.
6-16

INSPECTION AND MAINTENANCE
Interval: This interval should be judged byl, -----------------------=~"-f""'~----a'ica-l--i;ee+ odometer reading or months, whicheveq,r ___________________ =='='c~:,f-"'ii"-+-:;;;'----!-km (x100D) 10 I 20 I 30 I 40 I 50 I 60 miles (x1000) 6.25 I 12.5 I 18.75 I 25 I 31,25 I 37.5 comes first. I
BRAKE *5-1. Brake discs and pads (front) Brake drums and shoes (rear) *5-2. Brake hoses and pipes 5-3. Brake fluid (#3)
months
Check, *Replacement *5-4. Brake (Pedal and fluid level) 5-5. Brake lever and cable Check, *Adjustment (1st 20000 km only) CHASSIS ANO BODY *6-1. Clutch fluid (#3) *6-2. Clutch (Pedal and fluid level) 6-3. Tyres/Wheels *6-4. Wheel bearings *6-5. Propeller shafts *6-6. Suspension system *6-7. Steering system *6-8. Manual transmission oil
6-9. Automatic transmission
*6-10. Transfer oil
*6-11. Differential all 6-12. All latches, hinges and locks *6-13. Air conditioner filter elemenr·3
Genuine "SUZUKI GEAR OIL 75W"
Other than "SUZUKI GEAR OIL 75W"
Genuine "SUZUKI GEAR OIL 75W"
Other than "SUZUKI GEAR OIL 75W"
Fluid level *Fluid change *Fluid hose
Genuine "SUZUKI SUPER GEAR OIL 75W-85 SYNTHETIC"
#3: Clutch fiuid is supplied from brake fiuid reservoir.
A WARNING
6 I 12 I 18 I 24 I 30 I 36
-I -I -I ---I -----I -----R ---I -I -I -I ----
---R ---I -I -I -I -I -I -I -I -I -I -I -I ---I -----I --Inspect every 20000 km (12500 miles) or 12 months. Replace every 80000 km (50000 miles) or 48 months.
= I ~ I = I ~ I = I ~ Replace every 30000 km (18000 miles). Inspect every 60000 km (37500 miles). Inspect every 20000 km (12500 miles) or 12 months. Replace every 80000 km (50000 miles) or 48. months. -R -R -R -R ---R
R
The shock absorbers are filled with high pressure gas. Never attempt to disassemble them or throw them into a fire. Avoid storing them near a heater or heating device. When scrapping the absorber, the gas must be released from the absorber safely. Ask your dealer for assistance.
6-21

Brake discs and brake drums
Brake disc
Brake location Minimum thickness
Front wheels 8.0 mm (0.3 in.)
Brake drum
Brake location Maximum inner diameter
Rear wheels 222 mm (8.74 in.)
If the measured thickness or inner diame­ter of the most worn part falls below or exceeds the value indicated above, the parts should be replaced with a new one. The measurement involves disassembling each brake and requires the use of a micrometer or caliper, which must be done according to the instructions described in the relevant service manual or available from the relevant repair information site.
Steering wheel
78RB07012
Steering wheel play 11c": 0-30 mm (0.0 -1.2 in.)
Check the free play of the steering wheel by gently turning it from left to right and measuring the distance that it moves before you feel slight resistance. The play should be between the specified values.
Check that the steering wheel turns easily and smoothly without rattling by turning it all the way to the right and to the left while driving very slowly in an open area. If the amount of free play is not as specified or you find anything else to be wrong, an inspection must be performed by a SUZUKI dealer.
INSPECTION AND MAINTENANCE
Tyres
78RB07013
The front and rear tyre pressure specifica­tions are listed in the tyre information label. Both front and rear tyres should have the specified tyre pressure.
NOTE: The tyre pressure will change due to changes in atmospheric pressure, tem­perature or tyre temperature when driving. To reduce the chance that the low tyre pressure warning light (if equipped) will come on due to normal changes in tem­perature and atmospheric pressure, it is important to check and adjust the tyre pressures when the tyres are cold. If you check tyres after driving, they are warm. Even if the tyre pressure seems to be good in this condition, it could fall below the
6-36

SUPPLEMENT
If you must use a front-facing child restraint in the front passenger's seat, be sure to move the front passenger's seat as far back as possible. Please refer to "Seat belts and child restraint systems" in the "BEFORE DRIVING" section for details on securing your child.
Airbag symbol meaning
A (ill
AIRBAG ~
®
@~
72M00150
You may find this label on the sun visor.
A WARNING
NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur.
10-3
Seat belt warning
Follow this warning as well as the instruc­tion for seat belt in this book.
A WARNING
Seat belts are designed to bear upon the bony structure of the body, and should be worn low across the front of the pelvis or the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided. • Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed. A slack belt will greatly reduce the protection afforded to the wearer. • Care should be taken to avoid con­tamination of the webbing with pol­ishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged. (Continued)
A WARNING
(Continued) • It is essential to replace the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious. Belts should not be worn with straps twisted. Each belt assembly must only be used by one occupant; it is danger­ous to put a belt around a child being carried on the occupant's lap,
In the case where a "Seat Belt Assembly'' incorporates an "Automatic Length Adjust­ing and Locking Retractor' or an "Emer­gency Locking Retractor'.
A WARNING
No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack. Referring to the SEAT BELT instruction in this book, adjust the seat belt so that the lap and sash portions of the Seat Belt Assembly fit as firmly as possible consistent with comfort.