water pump SUZUKI JIMNY 2021 Owners Manual

OPERATING YOUR VEHICLE
Braking
60G165S
The distance needed to bring any vehicle to a halt increases with the speed of the vehicle. The braking distance needed, for example, at 60 km/h (37 mph) will be approximately 4 times greater than the braking distance needed at 30 km/h (19 mph). Start to depress the brake pedal when there is plenty of distance between your vehicle and the stopping point, and slow down gradually.
3-53
A WARNING
If water gets into the brake devices, brake performance may become poor and unpredictable. After driving through water or washing the under­side of the vehicle, test the brakes while driving at a slow speed to see if they have maintained their normal effectiveness. If the brakes are less effective than normal, dry them by repeatedly applying the brakes while driving slowly until the brakes have regained their normal effectiveness.
Power-assisted brakes
Your vehicle has power-assisted brakes. If power assistance is lost due to a stalled engine or other failures, the system is still fully operational on reserve power and you can bring the vehicle to a complete stop by pressing the brake pedal once and holding it down. The reserve power is partly used up when you depress the brake pedal and reduces each time the pedal is pressed. Apply smooth and even pressure to the pedal. Do not pump the pedal.
A WARNING
Even without reserve power in the brake system, you can still stop the vehicle by pressing the brake pedal harder than normally required. How­ever, the stopping distance may be
longer.
Brake assist system
When you slam the brakes on, the brake assist system determines it to be an emer­gency stop and provides more powerful braking for a driver who cannot hold down the brake pedal firmly.

INSPECTION AND MAINTENANCE
Drive belt
A WARNING
When the engine is running, keep hands, hair, clothing, tools, etc. away from the moving fan and drive belts.
Check that the drive belt tension is correct while the engine is stopped. If the belt is too loose, insufficient battery charging, engine overheating, poor air conditioning, or excessive belt wear can result. When you push the belt with your thumb midpoint between the pulleys, there should be a deflection according to the following chart.
The belts should also be examined to ensure that they are not damaged.
If you need to replace or adjust the belt have it done by a SUZUKI dealer.
6-23
(2) (4)
78RB07001
(1) Water pump (2) Generator
(3) Idler pulley
(4) Air conditioner compressor
Drive belt deflection (100 N (10 kg, 22 lbs) press)
(a) New: 4.8 -5.9 mm (0.19 -0.23 in.) Readjustment: 6.2 -7 .1 mm (0.24 -0.28 in.)
(b) New: 3.2 -4.1 mm (0.13 -0.16 in.) Readjustment: 4.4 -5.0 mm (0.17 -0.20 in.)
Engine oil and filter
Specified oil
Models for EU countries and Israel
< l:!W-JQ >
(1) < 0W-20 >
~< OW-16 > °C-30 -20 -10 0 10 20 30 40 °F -22 -4 14 32 50 68 86 104
78RB07002
( 1) Preferred
Check that the engine oil you use comes under the quality classification as listed below: • ACEA A1/81, A3/83, A3/84, AS/85 • API SL, SM, SN • ILSAC GF-3, GF-4, GF-5 Select the appropriate oil viscosity accord­ing to the above chart.

EMERGENCY SERVICE
If the high engine coolant temperature warning light does not go off or the tem­perature indication does not come down to within the normal, acceptable range:
1) Turn off the engine and check that the water pump belt and pulleys are not damaged or slipping. If any abnormality is found, correct it. 2) Check the coolant level in the reservoir. If it is found to be lower than "LOW" line, check radiator, water pump, radia­tor hoses and heater hoses for leakage. If leakage that may cause overheating is found, do not run the engine until these problems have been corrected. 3) If leakage is not found, carefully add coolant to the reservoir and then the radiator, if necessary. (Refer to "Engine coolant" in "INSPECTION AND MAIN­TENANCE" section.)
NOTE: If engine overheats and you are not sure what to do, contact a SUZUKI dealer.
7-11
650614
A WARNING
• It is hazardous to remove the radia­tor cap when the water temperature is high, because scalding fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant tem­perature has lowered. To help prevent personal injury, keep hands, tools and clothing away from the engine cooling fan and air-conditioner fan. These elec­tric fans can automatically turn on without warning.