engine SUZUKI MARUTI 2005 1.G User Guide
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2005, Model line: MARUTI, Model: SUZUKI MARUTI 2005 1.GPages: 136, PDF Size: 2.93 MB
Page 11 of 136
Downloaded from www.Manualslib.com manuals search engine 1183KFUEL RECOMMENDATION
FUEL RECOMMENDATION
Petrol Engine
You must use unleaded petrol with an
octane number (RON) of 91 or higher.
Diesel Engine
The diesel fuel should be with cetane num-
ber (CN) higher than 51 and sulphur con-
tent less than 350 ppm (parts per million).
Do not use marine diesel fuel, heating oils
and so forth.
Petrol/Ethanol blends
Blends of unleaded petrol and ethanol (grain
alcohol), also known as gasohol, are
commercially available in some areas.
Blends of this type may be used in your
vehicle if they are no more than 10% etha-
nol. Make sure this petrol-ethanol blend has
octane ratings no lower than those
recommended for petrol.
Petrol/Methanol blends
Blends of unleaded petrol and methanol
(wood alcohol) are also commercially avail-
able in some areas. DO NOT USE fuels
containing more than 5% methanol under any
circumstances. Fuel system damage or
vehicle performance problems resulting from
the use of such fuels are not the
responsibility of MARUTI SUZUKI and may
not be covered under the New Vehicle
Warranty.Fuels containing 5% or less methanol may
be suitable for use in your vehicle if they
contain cosolvents and corrosion inhibitors.
NOTE:
If you are not satisfied with the driveability
or fuel economy of your vehicle when you
are using a petrol/alcohol blend, you should
switch back to unleaded petrol containing no
alcohol.The fuel tank has an air space to
allow for fuel expansion in hot
weather. If you continue to add fuel
after the filler nozzle has automatically
shut off or an initial blowback occurs,
the air chamber will become full.
Exposure to heat when fully fuelled in
this manner will result in leakage due
to fuel expansion. To prevent such
fuel leakage, stop filling after the filler
nozzle has automatically shut off, or
when using an alternative non
automatic system, initial vent
blowback occurs.
CAUTION
CAUTION
Be careful not to spill fuel containing
alcohol while refueling. If fuel is
spilled on the vehicle body, wipe it up
immediately. Fuels containing alcohol
can cause paint damage, which is not
covered under the New Vehicle
Limited Warranty.
3-1
Page 12 of 136
Downloaded from www.Manualslib.com manuals search engine 1283K
BEFORE DRIVING
Keys ...................................................................................................................................... 4-1
Door Locks.......................................................................................................................... 4-2
Keyless Entry System Transmitter (if equipped)......................................................... 4-4
Mirrors................................................................................................................................ 4-13
Heated Rear Window Switch (if equipped).................................................................4-14
Front Seats........................................................................................................................ 4-14
Rear Seats......................................................................................................................... 4-16
Seat Belts and Child Restraint Systems.....................................................................4-18
Supplemental Restraint System (air bags) (if equipped).........................................4-24
Instrument Cluster (For Petrol & Diesel)....................................................................4-28
Warning and Indicator Lights........................................................................................4-29
Speedometer/Odometer/Trip meter/Meter Illumination Control................................4-34
Tachometer (if equipped)................................................................................................4-35
Fuel Gauge........................................................................................................................ 4-35
Lighting Control Lever....................................................................................................4-38
Front Fog Light Switch (if equipped)..........................................................................4-39
Rear Fog Light Switch (if equipped)............................................................................4-39
Headlight Leveling Switch.............................................................................................. 4-39
Turn Signal Control Lever.............................................................................................. 4-40
Hazard Warning Switch...................................................................................................4-40
Windshield Wiper and Washer Lever...........................................................................4-40
Rear Window Wiper/Washer Switch (if equipped).....................................................4-41
Tilt Steering Lock Lever (if equipped) ......................................................................... 4-42
Horn ..................................................................................................................................... 4-42
BEFORE DRIVING
Page 13 of 136
Downloaded from www.Manualslib.com manuals search engine 1383K
In case of attaching any metal objects
to the immobilizer key, it may not
start the engine.
The immobilizer key is a sensitive
electronic instrument. To avoid dam-
aging the immobilizer key:
Do not expose it to impacts, mois-
ture or high temperature such as by
leaving it on the dashboard under
direct sunlight.
Keep the immobilizer key away from
magnetic objects.
Keys
which has an electronic identification code
programmed into it. The key communicates
the identification code to the vehicle when
the key is turned to the “ON” position. If you
need to make spare keys, visit (contact)
your MARUTI SUZUKI authorized dealer.
The vehicle must be programmed with the
correct identification code for the spare
keys. A key made by an ordinary locksmith
will not work.
Your vehicle comes with a pair of identical
keys. Keep the spare key in a safe place.
One key can open all of the locks on the
vehicle.
The key identification number is stamped on
a metal tag provided with the keys or on
the keys. Keep the tag (if equipped) in a
safe place. If you lose your keys, you will
need this number to have new keys made.
Write the number below for your future ref-
erence.
KEY NUMBER
If the immobilizer system light (1) for petrol
engine or service vehicle soon (SVS) light
(2) for diesel engine blinks when the igni-
tion switch is in the “ON” position, there
may be something wrong with your key or
with the immobilizer system. Contact your
MARUTI SUZUKI authorized dealer to
inspect the system.NOTE:
If you lose your immobilizer ignition key,
contact your MARUTI SUZUKI dealer as
soon as possible to have the lost one
deactivated, then have the new key
made by them. If you own other vehicles with immobi-
lizer keys, keep those keys away from
the ignition switch when using your vehi-
cle, or the engine may not be started
because they may interfere with your
vehicle’s immobilizer system.
CAUTION
EXAMPLEBEFORE DRIVING
4-1
83K-02-001
Immobilizer System
This system is designed to help prevent
vehicle theft by electronically disabling the
engine starting system.
The engine can be started only with your
vehicle’s original immobilizer ignition key
83K-02-002
Ignition Key Reminder (if equipped)A buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
Page 14 of 136
Downloaded from www.Manualslib.com manuals search engine 1483K
Door LocksSide Door Locks
To lock a door from inside the vehicle, turn
the lock knob forward. Turn the lock knob
backward to unlock the door.
NOTE:
Be sure to hold the door handle up when
you close a locked front door, as the door
will not remain locked.
EXAMPLE BEFORE DRIVING
4-2
83K-02-003
To lock a front door from outside the vehi-
cle:
Insert the key and turn the top of the
key anti clockwise or
Turn the lock knob forward and hold the
door handle as you close the door.
To unlock a front door from outside the
vehicle, insert the key and turn the top of
the key clockwise.
To lock a door from outside the vehicle, turn
the lock knob forward and close the door.
83K-02-004
Central Door Locking SystemDriver’s door (if equipped)
You can lock and unlock all doors (includ-
ing the tailgate) simultaneously by using the
key in the driver’s door lock.
To lock all doors simultaneously, insert the
key in the driver’s door lock and turn the
top of the key anti-clockwiseTo unlock all doors simultaneously, insert
the key in a driver’s door lock and turn the
top of the key toward the front of the vehi-
cle twice.
To unlock the driver’s door only, insert the
key in that door lock and turn the top of
the key toward the front of the vehicle once.
You can also lock or unlock (4 or 5) all
doors by depressing the front or rear of the
switch (1), respectively.
NOTE:
If your vehicle is equipped with keyless
entry system, you can also lock or unlock
all doors by operating the transmitter. Refer
to “Keyless Entry System Transmitter”.
83K-02-006
EXAMPLE
Page 15 of 136
Downloaded from www.Manualslib.com manuals search engine 1583KNOTE:
Individual doors can also be UNLOCKED
anytime by using their respective "Door
Lock Knob" inside the vehicle.
If child proof locks are in locked position,
rear doors cannot be opened from inside.
w ww w
w WARNING
Be sure to place the child-proof lock
in the locked position whenever chil-
dren are seated in the rear.
BEFORE DRIVING
4-3
Child-Proof Locks (rear side door)
83K-02-007
EXAMPLEAs illustrated, a child-proof lock is provided
for both rear doors. When the lock lever is
in position (1), the child-proof lock is locked,
and when in position (2), the child-proof lock
is unlocked. When the child-proof lock is in
the locked position, the rear door cannot be
opened from the inside even if the inside
door lock is unlocked but can be opened
from the outside.
Manual tailgate unlatchType1 (if equipped)
83K-02-008
EXAMPLETo open the tailgate, insert the key and turn
it clockwise to unlatch and lift the tailgate.You can also unlatch the tailgate-trunk lid by
pulling the release lever (if equipped) located
on the outboard side of the driver’s seat.
Type2 (if equipped)
83K-02-00983K-02-010
EXAMPLE
EXAMPLE(1) Tailgate handle
Page 16 of 136
Downloaded from www.Manualslib.com manuals search engine 1683K
You can lock and unlock the tailgate by
using the key in the driver’s door lock.
To open the tailgate, pull up and hold the
tailgate unlatch handle (1) and lift the tailgate.
w ww w
w WARNING
Always make sure that the tailgate is
closed and latched securely. Com-
pletely closing the tailgate helps pre-
vent occupants from being thrown
from the vehicle in the event of an
accident. Completely closing it also
helps keep away exhaust gases from
entering the car.BEFORE DRIVING
4-4
83K-02-011
2) Push open the tailgate from inside by
pushing up on the emergency lever (2)
using a flat blade screw driver or the
jack handle. The tailgate will be latched
again by closing the tailgate simply.
If the tailgate can not be unlatched by pull-
ing up the tailgate unlatch switch (1), have
the vehicle inspected by your MARUTI
SUZUKI authorized dealer. If you can not unlatch the tailgate by pulling
up the unlatch handle (1) due to a malfunc-
tion, follow the procedures below to unlatch
the tailgate from inside the vehicle.
1) Fold the rear seat forward for easier
access. Refer to “Folding Rear Seats”
section for details on how to fold the
rear seat forward.
w ww w
w WARNING
To avoid injury, do not use your fin-
ger to push the emergency lever.
Make sure there is no one near the
tailgate when pushing open the tail-
gate from inside the vehicle.
Keyless Entry System Trans-
mitter (if equipped)
83K-02-012
(1) “LOCK” button
(2) “UNLOCK” button
There are two ways to lock or unlock all
doors (including the tailgate) simultaneously
by operating the transmitter near the vehicle.
Central door locking system
To lock all doors, push the “LOCK” but-
ton (1) once.
To unlock all other doors, push the
“UNLOCK” button (2) once.
The turn signal lights will flash once when
the doors are locked.
When the doors are unlocked:
The turn signal lights will flash twice.
If the interior light switch is in the middle
position, the interior light will turn on for
about 15 seconds and then fade out. If
you insert the key into the ignition switch
during this time, the light will start to
fade out immediately.
Page 17 of 136
Downloaded from www.Manualslib.com manuals search engine 1783K
BEFORE DRIVING
4-5
Be sure the doors are locked after you
operate the “LOCK” button. If no door is
opened within about 30 seconds after the
“UNLOCK” button is operated, the doors will
automatically lock again.NOTE:
The maximum operating distance of the
keyless entry system transmitter is about
5 m (16 ft.), but this can vary depending
on the surroundings, especially near
other transmitting devices such as radio
towers or CB (citizen’s band).
The door locks can not be operated with
the transmitter if the ignition switch is in
a position other than “LOCK”, or the igni-
tion key is inserted in the ignition switch.
When any door is open, the door locks
can be operated only unlock with the
transmitter, and the turn signal light will
not flash.
If you lose one of the transmitters, con-
tact your MARUTI SUZUKI authorized
dealer as soon as possible for a replace-
ment. Be sure to have your dealer pro-
gram the new transmitter code in your
vehicle’s memory so that the old code
is erased.
CAUTION
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
Do not expose it to impacts, mois-
ture or high temperature such as by
leaving it on the dashboard under
direct sunlight.
Keep the transmitter away from
magnetic objects such as a televi-
sion.
Replacement of the Battery
If the transmitter gets discharged, replace
the battery with a new one.
To replace the battery of the transmitter:
83K-02-013
1) Remove the screw (1), and open the
transmitter cover.2) Remove the transmitter (2).
3) Put the edge of a flat blade screw driver
in the slot of the transmitter (2) and pry
it open.
4) Replace the battery (3) (Lithium disc-type
CR1620 or equivalent) so its + terminal
faces the “+” mark of the transmitter.
5) Close the transmitter and install it into
the transmitter holder.
6) Close the transmitter cover, install and
tighten the screw (1).
7) Make sure the door locks can be oper-
ated with the transmitter.
8) Dispose of the used battery properly
according to applicable rules or regula-
tions. Do not dispose of lithium batter-
ies with ordinary household trash.
CAUTIONw ww w
w WARNING
Swallowing a lithium battery may
cause serious internal injury. Do not
allow anyone to swallow a lithium
battery. Keep lithium batteries away
from children and pets. If swallowed,
contact a physician immediately.
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
it, do not expose it to dust or mois-
ture or tamper with internal parts.
Page 18 of 136
Downloaded from www.Manualslib.com manuals search engine 1883K
BEFORE DRIVING
4-6Keyless Entry Cum Alarm
System (if equipped)System
83K-02-015
The Keyless Entry Cum Alarm System has
two basic modes of operation.
VALET MODE
When the vehicle is to be given for servic-
ing or Valet parking, turn the system into
Valet mode. In Valet mode all the Security
features of system will be OFF. The Sys-
tem will work as a Keyless Entry/Exit in this
mode.
83K-02-016
designed to protect your vehicle from
unauthorized entry. The system can be
operated in three stages. The First is “Arm
Stage” , Second is “ Trigger Stage” & Third
is “Disarm Stage”.
ALARM MODE
Alarm mode system is in three stages: Arm,
Disarm & Trigger stage. The system is
83K-02-017
83K-02-018
ARM STAGE
In Arm Stage, your vehicle is safe from any
unauthorized entry.
1) Press and release the Key Lock button.
2) One Siren chirp and one indicator light
flash will confirm Arm and Lock.
3) Doors will get locked and vehicle will get
armed.
4) Visible theft warning LED on security
switch will flash slowly.NOTE: System will not Arm in following
condition:
1. If any of door is open (except Bonnet).
2. If System is in Valet Mode.
3. If Key is in key cylinder.
TRIGGER STAGE
If anybody tries to tamper with the vehicle,
the alarm triggers and indicators flashes
DISARM STAGE
System should be brought in Disarm Mode
83K-02-019
Page 19 of 136
Downloaded from www.Manualslib.com manuals search engine 1983K
BEFORE DRIVING
4-7
while you are entering/exiting the vehicle.
a) Press and release the Key Unlock but-
ton.
b) Two Siren chrip and two indicator light-
flashes will confirm Disarm and Unlock.
c) Doors will get Unlock and vehicle will get
disarmed.
d) Visible theft warning LED on security
switch will flash fastly.
83K-02-020
Panic Alarm (Car Locator)
Panic Alarm is designed to bring attention
to the vehicle and to locate the vehicle in
congested packed parking area.
a) Press and hold the Key Lock & Unlock-
button simultaneously for 3 seconds.b) Panic alarm will be activated and siren
will sound and indicator lights will flash
for 30 seconds.
c) Press and release the Key Lock &
Unlock button simultaneously within 30
seconds to cancel the Panic alarm.
General FeatureMute Lock/Unlock
To Arm/Disram the vehicle without siren
chirps use this function.
a) Press and release the Key Lock &
Unlock buttons simultaneously.
b) Press and release Key Lock or Unlock
button for desired function.Example: To Lock the system without the
Siren chirp sound, press and release the Key
Lock & Unlock button simultaneously, then
press and release the Key Lock button.Auto Rearm
In case of accidental Unlock/Disarm of
vehicle by Key, vehicle will automatically
Lock & Arm within 30 sec. without any indi-
cation, if no door is opened in this 30 sec.NOTE : If the vehicle is in Valet Mode sys-
tem will only Lock the vehicle.Radio Frequency Lock Out
Key Lock/Unlock/Panic will ceases to func-
tion when Key is present in Key cylinder.Flashing LED Status
The flashing LED always reflects the status
of the system as following.
SYSTEM CONDITION LED STATUS
Disarmed condition LED does not glow
Armed condition Slow Flashes of LEDDiagnostic report Visual-LED Sound
Built in shock 2 Flashes Four Chirps
sensor Triggered
Door / Trunk 3 Flashes Four Chirps
Instrusion
Ignition 5 Flashes Four ChirpsIntrusion Alert
The system gives a report if it has been
tampered in your absence.
Programmable Features
System have some feature which can be
programmed by user according to their
choice.
Drive Lock Mode
Drive lock mode can be programmed by
SPEED or can be turn OFF. In case of
drive lock mode is programmed to SPEED
LOCK, all the vehicle doors will lock when
vehicle attains the speed of 20 Km/hr. If
Drive Lock is programmed to OFF, no door
will lock by speed.
Page 20 of 136
Downloaded from www.Manualslib.com manuals search engine 2083K
BEFORE DRIVING
4-8NOTE: In case of Speed Lock feature, open
& close of Door while driving will cause
cancellation of Speed Lock.Drive Unlock Mode
Drive unlock can be programmed by KEY
or can be turn OFF. When programmed to
KEY, turning IGN ON-OFF, then removing
the key from the key cylinder will unlock all
the doors. In case if drive unlock is pro-
grammed to OFF then no door will unlock
by removing key from key cylinder.
Siren Chirp ON/OFF feature
Siren Chirps are produced whenever Sys-
tem is Arm/Disarm by key. When siren chirp
feature disabled, siren will not chirp after
Arm/Disarm by Key.
Shock Sensor feature
This is a very important feature of security
system, It enables protection of your veh-
cle against any major impact. If anybody
tries to tamper with the vehicle, the alarm
triggers. The triggering of the alarm is in
two stages, first acting as a warning to the
intruder and then at full blast. The sensitivity
of impact sensor can be adjusted as desired
by the user.
Programming Drive Lock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the key cylinder,
turn IGN ON and then switch it OFF.c) Press and release the Security switch
One time.
d) Press and hold the Security switch.
e) One chirp sound confirms entry into
Drive Lock programming mode.
f) Press the Key Lock button (while holding
the Security switch), a single chirp sound
confirms mode changed to speed lock.
g) Two-Siren chirp sound confirms Drive
lock mode OFF.
h) Release the Security switch.
i) Turn the IGN ON.
Programming Drive Unlock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the key cylinder,
turn IGN ON and then switch it OFF.
c) Press and release the Security switch
two times.
d) Press and hold the Security switch.
e) Two-chirp sound confirms entry into
Drive unlock programming mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
key Unlock.
g) Two-siren chirp sound confirms the
mode changed to Drive Unlock mode
OFF.
h) Release the Security switch.
i) Turn the IGN ON.Programming Siren Chirp ON/OFF
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the key cylinder,
turn IGN ON and then switch it OFF.
c) Press and release the Security switch
Three times.
d) Press and hold the Security switch.
e) Three-chirp sound confirms entry into
Siren Chirp ON/OFF programming mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single sound
confirms the mode changed to Siren
Chirp ON.
g) Two-Siren chirp sound confirms the
mode changed to Siren Chirp OFF.
h) Release the Security switch.
i) Turn the IGN ON. Procedure To Program Feature
Feature 1 Chirp 2 Chirps Default
1. Drive Lock
Mode Speed OFF Speed
2. Drive Unlock
Mode Key OFF Key
3. Siren chirp
ON/OFF ON OFF ON
4. Shock Sensor
ON/OFF ON OFF ON