battery SUZUKI NEXA 2015 1.G Owner's Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2015, Model line: NEXA, Model: SUZUKI NEXA 2015 1.GPages: 288, PDF Size: 8.02 MB
Page 145 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
) U R Q W Z L W K R X W R Y H U K H D G F R Q V R O H
61MM0A205
Push the switch to turn on the light and
push it again to turn off the light.
) U R Q W Z L W K R Y H U K H D G F R Q V R O H
64MS119
& H Q W H U
61MM0A107
These light switches have three or four
positions with function as described below: 2 1 D
• The light comes on and stays on regard-
less of whether the door is open or
closed.
• To save the battery, the light will be auto-
matically turned off when a period of 15
minutes has elapsed after the light is on.
' 2 2 5 E
• The light comes on when the door is
opened. After closing all doors, the light
will remain on for about 15 seconds and
then fade out. If you insert the key, or
press the engine switch to change the
ignition mode to ACC or ON during this
time, the light will start to fade out imme-
diately. After removing the key from the
ignition switch, the light will turn on for
about 15 seconds and then fade out.
• Regardless of whether the door is open
or closed, the light comes on 15 seconds
and then fade out when the ignition
mode is changed to LOCK (OFF) or the
ignition switch is turned to the “LOCK”
position.
2 ) ) F
The light remains off even when the door is
opened.
6 3 2 7 / , * + 7 G
When the light switch is in the DOOR or
OFF position, push the switch to turn on
the light and push it again to turn off the
light. ( ; $ 0 3 / (
(d) (c) (b) (a) (d)
(a)
(b)
(c)
( ; $ 0 3 / (
Page 191 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
NOTE:
If text data contains more than 12 charac-
ters, the “>” mark will appear at the right
end. Holding down the DISP button (7) for
1 second or longer can display the next
page.
3 O D \ L Q J 0 R G H V H O H F W L R Q
1) Press the button numbered [6] of the
Preset buttons (8) for 1 second or lon-
ger.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2).
Each time the knob is turned, the mode
will change as follows:
3) Press the TUNE FOLDER PUSH
SOUND knob (2) to select the desired
mode.
NOTE:
• When the button numbered [6] of the
Preset buttons (8) is pressed, the previ-
ous mode will be displayed.
1 R W H V R Q L 3 R G
Š
6 X S S R U W H G L 3 R G
Š
•iPod
® touch (5th generation)
•iPod® touch (4th generation)
•iPod® touch (3rd generation)
•iPod® touch (2nd generation)
•iPod® touch (1st generation)
•iPod® classic
•iPod® nano (7th generation)
•iPod® nano (6th generation)
•iPod® nano (5th generation)
•iPod® nano (4th generation)
•iPod® nano (3rd generation)
•iPod® nano (2nd generation)
•iPod® nano (1st generation)
•iPod® (5th generation)
•iPod® (6th generation)
•iPod®(6thPlus generation)
•iPhone® 6 / 6 plus
• iPhone® 5
• iPhone® 4S
• iPhone® 4
• iPhone® 3GS
• iPhone® 3G
• iPhone®
* Some functions may not be available
depending on the model of iPod
®.
*iPod
® is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
*iPhone® is a trademark of Apple Inc.,
registered in the U.S. and other coun-
tries.
* Apple is not responsible for the opera-
tion of this device or its compliance with
safety and regulatory standards. L 3 R G
Š F R Q Q H F W L R Q
• Make sure to detach the iPod
® after
pressing the engine switch to change the
ignition mode to “LOCK” (OFF) or the
ignition switch is turned to the “LOCK”
position. The iPod
® may not be shut
down when it is being connected and
may result in battery depletion.
• Please do not connect iPod
® accesso-
ries such as an iPod
® remote control or
headphones while connecting the iPod
®
with the unit. The unit may not operate
correctly.
PLAYLIST
ARTIST
ALBUM
SONGS
GENRE
Page 208 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
The anti-theft function is intended to dis-
courage thefts, such as that the audio sys-
tem becomes inoperable when it is installed
on other vehicles.
This function works by entering a Personal
Identification Number (PIN).
When the unit is disconnected from its
power source, such as when the audio sys-
tem is removed or the battery is discon-
nected, the unit will become inoperable until
the PIN is reentered. 6 H W W L Q J W K H $ Q W L 7 K H I W ) X Q F W L R Q1) Press the VOL PUSH POWER knob (1)
to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob (1).
“SECURITY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or longer
to set the anti-theft function.NOTE:
Take a note of the registered PIN and keep
it for the future use. & D Q F H O L Q J W K H D Q W L W K H I W I H D W X U H
To cancel the anti-theft function, delete the
registered PIN.
1) Press the VOL PUSH POWER knob
(1) to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob
(1).
“PIN ENTRY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or lon-
ger to delete the registered PIN. The
indication “----” will be displayed and
the anti-theft function will be canceled.
NOTE:
To change your PIN, first delete your cur-
rent PIN, then set a new one. & R Q I L U P L Q J W K H 3 H U V R Q D O , G H Q W L I L F D W L R Q
1 X P E H U 3 , 1
When the main power source is discon-
nected such as when the battery is
replaced, etc, it is required to enter the PIN
to make the unit operable again.
1) Set the ignition switch to the “ACC”
position.
“SECURITY” will be displayed.
2) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
3) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
4) Hold down TUNE FOLDER PUSH
SOUND knob (4) for 1 second or lon-
ger.
When the PIN same as registered is
entered, the power of the audio system
will be turned off automatically and it
will become operable again.
NOTE:
If an incorrect PIN is entered, “ERROR”
and the total number of incorrect entry
attempts will be displayed.
If an incorrect PIN is entered 10 times or
more, “HELP” will be displayed and the
audio system will become inoperable.
Page 209 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
% D W W H U \ , Q V W D O O D W L R QInstall a lithium battery (CR2025) with the poles facing the correct direction.
% D W W H U \ U H S O D F H P H Q W W L P L Q J
• When battery power is depleted, the button may not be operable. If the remote controller
does not operate, replace the battery and check the operation.
& D X W L R Q R Q E D W W H U \
• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or
explosion.
If battery leakage has occurred, wipe the
container first then install a new battery. If
the battery solution contacts the skin, wash
off with water completely.
& D X W L R Q R Q 5 H P R W H & R Q W U R O O H U• Do not leave the remote controller in an
area exposed to direct sunlight, such as
on the dashboard or steering wheel. The
remote controller may deform because of
the heat, (Be especially careful of the
dashboard exposed to direct sunlight in
the summer, as it will become extremely
hot).
: $ 5 1 , 1 *
Page 227 of 288
Downloaded from www.Manualslib.com manuals search engine 7-4
INSPECTION AND MAINTENANCE
64MS0-74E
Interval: This interval should be judged by odometer reading
or months, whichever comes first.
FREE INSPECTION
PERIODIC MAINTENANCE AT COST
km (x1000)
1
5
10
20
30
40
50
60
70
80
months
1
6
12
24
36
48
60
72
84
96
5-5.
Brake drum and shoes (Wear)
-
-
I
I
I
I
I
I
I
I
5-6.Master cylinder and wheel cylinder or caliper, brake hoses and pipes (Fluid
leakage, damage)IIIIIIIIII
5-7.
Master cylinder sub assembly, wheel cylinder boot kit & caliper seal set
I
I
I
I
I
R
I
I
I
R
WHEEL
6-1.
Tyres (air pressure, abnormal wear, crack and rotation)
I
I&O
I&O
I&O
I&O
I&O
I&O
I&O
I&O
I&O
6-2. Wheels (Damage) I I I IIIIIII
6-3.
Front/Rear wheel bearing (Loose, damage)
I
I
I
I
I
I
I
I
I
I
FRONT / REAR SUSPENSION
7-1.
Suspension strut (Oil leakage, damage)
I
I
I
I
I
I
I
I
I
I
7-2. Suspension arms / Knuckle support (Loose, damage) – I I I I I I I I I
7-3.
Rear spring (Damage)
I
I
I
I
I
I
I
I
I
I
7-4.Shock absorbers (Oil leakage, damage) I I I I IIIIII
7-5.
All bolts and nuts (Loose)
–
T
T
T
T
T
T
T
T
T
7-6.Torsion rods – I I I I I I I I I
STEERING
8-1.
Steering wheel (Play, loose)
I
I
I
I
I
I
I
I
I
I
8-2.Steering column and tie rods (Loose, damage, wear) I I I I I I I I I I
ELECTRICAL
9-1.
Battery electrolyte (Level, leakage)
I
I
I
I
I
I
I
I
I
I
9-2. Wiring harness connection (Loose, damage) – I I I I I I I I I
9-3.
Lighting system (Operation, stains, damage)
I
I
I
I
I
I
I
I
I
I
9-4.Horn (Operation) IIIIII I II I
9-5.
System Voltage
)
I
I
I
I
I
I
I
I
I
BODY
10-1.
All chassis bolts and nuts (Tighten)
–
I
T
T
T
T
T
T
T
T
10-2. All latches, hinges and locks (Function)) I I&L I&L I&L I&L I&L I&L I&L I&L I&L
Page 241 of 288
Downloaded from www.Manualslib.com manuals search engine 7-18
INSPECTION AND MAINTENANCE
64MS0-74E
Wheel AlignmentIn case of abnormal tyre wear or pull
ing
towards one s
ide, have the wheel al
igned
at
A U T H O R I S E D - A R U T I 3 U Z U K I . % 8 ! D E A L E R
W O R K S H O P
Tubeless Tyres (If equipped)The veh
icle
is equ
ipped w
ith Tubeless
Tyres
. In tubeless tyre, a th
in layer of butyl
rubber
is used for l
ining the
inside of the
tubeless tyre
. Th
is layer
is to prevent a
ir
loss and fulf
illing the purpose of tube
. The
a
ir pressure
is ma
inta
ined by the seal
ing
between tyre bead and wheel r
im. Tube-
less tyres are hav
ing advantage of slow a
ir
loss and prevent
ing sudden deflat
ion wh
ile
dr
iving.Care and maintenance tips for tubeless
tyres
1) Always ma
inta
in recommended
inflat
ion
pressure
. Dr
iving cont
inuously at low
inflat
ion pressure can lead to tyre dam-
age.
2) In case any leakage
is found, check for
any na
il penetrat
ion/valve core dam-
age or r
im bent
. Damaged wheel must
not be used
.
3) In case tyre has run at low pressure,
it
must be
inspected for any defect
.
4) Whenever new tyre
is fitted, replace the
valve
.
5) If cont
inuous h
igh speed dr
iving
is
requ
ired,
increase tyres pressure by 5
ps
i over recommended
inflat
ion pres-
sure
.
6) Never run the tyre beyond TWI (Tread
wear
indicator)
. The tyre
is recommen-
ded to be replaced when the rema
ining
tread has worn to th
is po
int. The
indica-
tors are spaced across the tread
around the tyre marked by a tr
iangular
symbol (TWI)
.
7) Always prefer tubeless tyre mount
ing
mach
ine. In case of manual mount
ing-
tyre/wheel r
im damage may occur
.
8)
In case of any problem, please get
in
touch w
ith
A U T H O R I S E D - A R U T I 3 U Z U K I
W O R K S H O P
Battery
WA R N I N G
• Batteries produce flammable
hydrogen gas. Keep flames and
sparks away from the battery or an
explosion may occur. Never smoke
when working in the vicinity of the
battery.
• When checking or servicing the
battery, disconnect the negative
cable. Be careful not to cause a
short circuit by allowing metal
objects to contact the battery posts
and the vehicle at the same time.
• To avoid harm to yourself or dam-
age to your vehicle or battery, fol-
low the jump starting instructions
in the “EMERGENCY SERVICE”
section of this manual if it is neces-
sary to jump start your vehicle.
• Diluted sulfuric acid spilled from
battery can cause blindness or
severe burns. Use proper eye pro-
tection and gloves. Flush eyes or
body with ample water and get
medical care immediately if suf-
fered. Keep batteries out of the
reach of children.
Wheel BalancingIf the veh
icle v
ibrates abnormally on
smooth road, have the wheel balanced at
A U T H O R I S E D - A R U T I 3 U Z U K I W O R K S H O P
Page 242 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
76MS006
7he level of the battery solution must be
kept between the upper level line (1)
and lower level line (2) at all times. If the
level is found to be below the lower level
line (2), add distilled water to the upper
level line (1). You should periodically check
the battery, battery terminals, and battery
hold-down bracket for corrosion. Remove
corrosion using a stiff brush and ammonia
mixed with water, or baking soda mixed
with water. After removing corrosion, rinse
with clean water.
If your vehicle is not going to be driven for
a month or longer, disconnect the cable
from the negative terminal of the battery to
help prevent discharge. 5 H S O D F H P H Q W R I W K H E D W W H U \
) R U ' $ ' L H V H O ( Q J L Q H 0 R G H O
64MS160
NOTE:
(For D13A Diesel Engine Model)
To approach the battery, remove the suc-
tion pipe (1). ) R U ' $ $ ' L H V H O ( Q J L Q H 0 R G H O
61MS2A006
NOTE:
(For D16AA Diesel Engine Model)
To approach the battery, loosen the bolts,
push the locks and remove the suction
pipe (1).
( ; $ 0 3 / (
(1)
( ; $ 0 3 / (
(1)
( ; $ 0 3 / (
Page 243 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
51KM039
To remove the battery:
1) Disconnect the negative cable (1).
2) Disconnect the positive cable (2).
3) Remove the bracket bolt (3) and
remove the bracket (4).
4) Remove the battery.
To install the battery:
1) Install the battery in the reverse order of
removal.
64MS176
NOTE:
When putting the battery in the battery tray,
make sure the recess on the terminal side
bottom of the battery engages with the
convex portion of the tray.
2) Tighten the bracket bolt and battery
cables securely.
NOTE:
When the battery is disconnected, some of
the vehicle’s function will be initialized and/
or deactivated.
These function are required to reset after
the battery is reconnected.
) X V H VYour vehicle has three types of fuses, as
described below:
0 D L Q I X V H
The main fuse takes current directly from
the battery.
3 U L P D U \ I X V H V
These fuses are between the main fuse
and individual fuses, and are for electrical
load groups.
, Q G L Y L G X D O I X V H V
These fuses are for individual electrical cir-
cuits.
To remove a fuse, use the fuse puller (1)
provided in the fuse cover.
64MS198
(1)
(2)
(3)
(4)
( ; $ 0 3 / (
( ; $ 0 3 / (
(1)
Page 244 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
) X V H V L Q W K H ( Q J L Q H & R P S D U W P H Q W
61MM0B068
64MS177
The main fuse, primary fuses and some of the
individual fuses are located in the engine
compartment. If the main fuse blows, no elec-
trical component will function. If a primary fuse
blows, no electrical component in the corre-
sponding load group will function. When
replacing the main fuse, a primary fuse or an
individual fuse, use a 0 D U X W L * H Q X L Q H 3 D U W To
remove a fuse, use the fuse puller provided in
the fuse box. The amperage of each fuse is
shown in the back of the fuse box cover.
(6)
(7) (1)
(2)
(3)
(4)
(5)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)(18)
(19)
(20)
(21)
(22)
(23)(24)
(25)
(26)
(27)
(28)(29)
(30)
(31)
(32)
(33)
(34)
(35)
0 $ , 1 ) 8 6 ( 3 5 , 0 $ 5 < ) 8 6 (
(1) 60 A FL7
(2) 80 A FL6
(3)
100 A
FL5
(4)
80 A
FL4
(5)
100 A
FL3
(6)
100 A
FL2
(7)
120 A
FL1
(8) 7.5 AIgnition-1 signal 2 (D16AA)
(9) 30 A Radiator fan 2
(10) 20 A Front fog light
(11) 7.5 A Headlight 2
(12) 25 A ABS control module
(13) 25 A Headlight
(14) 30 A Back up
(15) 40 A Ignition switch
(16) 40 A ABS motor
(17) 30 A Starting motor
(18) 30 A Radiator fan
(19) 30 A FI main
(20) 20 A Fuel pump
(21) 10 A Air compressor
(22) 7.5 A ECM (D13A)
(23) 30 A Blower fan
(24) 10 A FI 2 (D13A)
(25) 20 A INJ DRV (D13A)
(26) 7.5 A Starting signal
(27) 15 A Headlight (Left)
(28) 15 A Headlight high (Left)
(29) 7.5 A FI 2 (D16AA)
(30) 20 A INJ DRV (D16AA)
(31) 15 A FI 3 (D16AA)
(32) 15 A Headlight (Right)
(33) 15 A Headlight high (Right)
(34) 50 A Ignition switch 2
(35) 50 A Battery
Page 268 of 288
Downloaded from www.Manualslib.com manuals search engine ( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
- X P S V W D U W L Q J L Q V W U X F W L R Q V
: K H Q - X P S 6 W D U W L Q J < R X U 9 H K L F O H
8 V H W K H ) R O O R Z L Q J 3 U R F H G X U H 1) Use only a 12-volt battery to jump start
your vehicle. Position the good 12-volt
battery close to your vehicle so that the
jump leads will reach both batteries.
When using a battery installed on
another vehicle, DO NOT LET THE
VEHICLES TOUCH. Set the parking
brakes fully on both vehicles.
2) Turn off all vehicle accessories, except
those necessary for safety reasons (for
example, headlights or hazard lights).
54MN259
3) Make jump lead connections as follows:
1. Connect one end of the first jump
lead to the positive (+) terminal of the
flat battery (1).
2. Connect the other end to the positive
(+) terminal of the booster battery (2).
3. Connect one end of the second jump
lead to the negative (–) terminal of the
booster battery (2).
4. Make the final connection to an
unpainted, heavy metal part (i.e.
engine mount bracket (3)) of the
engine of the vehicle with the flat bat-
tery (1).
: $ 5 1 , 1 *