ignition SUZUKI NEXA 2015 1.G Owner's Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2015, Model line: NEXA, Model: SUZUKI NEXA 2015 1.GPages: 288, PDF Size: 8.02 MB
Page 67 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
, Q I R U P D W L R Q ' L V S O D \The information display is shown when the
ignition switch is in the “ON” position or the
ignition mode is ON.
64MS183
(1) Information display
64MS184
(2) Indicator selector knob
(3) Trip meter selector knob
The information display shows the follow-
ing information. ' L V S O D \ $
Clock
' L V S O D \ %
Thermometer
' L V S O D \ &
Warning and indicator messages /
Fuel consumption / Driving range /
Average speed
' L V S O D \ '
Trip meter
' L V S O D \ (
Odometer
64MS181
When the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON, the message shown in the above illus-
tration will appear on the display for sev-
eral seconds.
Some warning and indicator messages
may appear on the display when the igni-
tion switch is in the “ACC” or “LOCK” posi-
tion, or the ignition mode is ACC or LOCK
(OFF).
& O R F NThe display (A) shows the time.
To set the clock, follow the “Setting mode”
instructions in this section. 7 K H U P R P H W H UThe display (B) shows the thermometer.
The thermometer indicates the outside
temperature.
61MM0A160
If the outside temperature nears freezing,
the message shown in the above illustra-
tion will appear on the display.
NOTE:
The outside temperature indication is not
the actual outside temperature when driv-
ing at low speed, or when stopped.
(1)(B)
(C) (A)
(D)
(E)
(3)
(2)
( ; $ 0 3 / (
Page 69 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
, Q V W D Q W D Q H R X V I X H O F R Q V X P S W L R Q
The display shows instantaneous fuel con-
sumption with a bar graph only when the
vehicle is moving.
NOTE:
• The display does not show the bar graph
unless the vehicle is moving.
• Depending on the vehicle’s specification,
the fuel consumption units of initial set-
ting are indicated as L/100km, km/L or
MPG.
• For “L/100km” or “km/L” setting, the indi-
cated maximum value of instantaneous
fuel consumption is 30. No more than 30
will be indicated on the display even if
the actual instantaneous fuel consump-
tion is higher.
• For “MPG” setting, the indicated maxi-
mum value of instantaneous fuel con-
sumption is 80. No more than 80 will be
indicated on the display even if the
actual instantaneous fuel consumption is
higher.
• The indication on the display may be
delayed if fuel consumption is greatly
affected by driving conditions.
• The display shows estimated values.
Indications may not be the same as
actual values.
$ Y H U D J H I X H O F R Q V X P S W L R Q
If you selected average fuel consumption
the last time you drove the vehicle, the dis-
play shows the last value of average fuel
consumption from previous driving when
the ignition switch is turned to the “ON”position or the engine switch is pressed to
change the ignition mode to “ON”. Unless
you reset the value of average fuel con-
sumption, the display indicates the value of
average fuel consumption which includes
average fuel consumption during previous
driving.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the value of average
fuel consumption will be shown after driv-
ing for a period of time.
You can select when the value of average
fuel consumption is reset from among the
following three methods;
• Reset after refuel: the value of average
fuel consumption will be reset automati-
cally by refueling.
• Reset with trip A: the value of average
fuel consumption will be reset automati-
cally by resetting trip meter A.
• Reset manually: the value of average
fuel consumption will be reset by push-
ing and holding the indicator selector
knob (2) when the display indicates the
average fuel consumption.
To change when the value of average fuel
consumption is reset, refer to “Setting
Mode” later in this section.
NOTE:
If you add only a small amount of fuel
when you select “Reset after refuel”, the
average fuel consumption value may not
be reset. ' U L Y L Q J U D Q J H
If you selected driving range the last time
you drove the vehicle, the display indicates
“---” for a few seconds and then indicates
the current driving range when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to ON.
The driving range shown in the display is
the approximate distance you can drive
until the fuel gauge indicates “E”, based on
current driving conditions.
When the low fuel warning light comes on,
the display “---” will appear.
If the low fuel warning light comes on, fill
the fuel tank immediately.
As the driving range after refueling is cal-
culated based on the most recent driving
condition, the value is different each time
you refuel.
NOTE:
• If you refuel when the ignition switch is in
the “ON” position or the ignition mode is
“ON”, the driving range may not indicate
the correct value.
• When you reconnect the negative (–)
terminal to the battery, the value of driv-
ing range will be shown after driving for a
period of time.
Page 70 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
$ Y H U D J H 6 S H H G
If you selected average speed the last time
you drove the vehicle, the display indicates
the last value of average speed from
previous driving when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition
mode to “ON”. Unless you reset the value
of average speed, the display indicates the
value of average speed which includes
average speed during previous driving.
To reset the value of average speed, push
and hold the indicator selector knob (2) for
about 2 seconds when the display indicates
an average speed. The display shows “---”
and then indicates a new average speed
after driving for a short time.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the value of average
speed will be shown after driving for a
period of time. 7 U L S 0 H W H UThe display (D) shows the trip meter.
The trip meter can be used to measure the
distance traveled on short trips or between
fuel stops.
You can use the trip meter A or trip meter B
independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (3) for
about 2 seconds when the display shows
the trip meter.
2 G R P H W H UThe display (E) shows the odometer.
The odometer records the total distance
the vehicle has been driven. 6 H W W L Q J 0 R G HWhen the ignition switch is in the “ON”
position or the ignition mode is ON and the
vehicle is stationary, you can enter the set-
ting mode of the information display by
pushing and holding the indicator selector
knob (2) for more than 3 seconds.
• To select the setting that you want to
change, turn the indicator selector knob
(2) left or right.
• To change the setting, push the indicator
selector knob (2).
• To exit the setting mode, select “Back”
and push the indicator selector knob (2).
61MM0A161
NOTE:
The currently selected setting item is indi-
cated enclosed by a frame.
NOTE:
• If you push and hold the indicator selec-
tor knob (2) to enter the setting mode
when the display (D) shows average fuel
consumption or average speed, the
value will be reset simultaneously. If you
do not want to reset the value, push the
indicator selector knob quickly to switch
the indication of the display.
• If you turn the ignition switch, press the
engine switch or start to move the vehi-
cle when the display is in the setting
mode, the setting mode will be canceled
automatically.
NOTICE
. H H S W U D F N R I \ R X U R G R P H W H U U H D G L Q J
D Q G F K H F N W K H P D L Q W H Q D Q F H V F K H G
X O H U H J X O D U O \ I R U U H T X L U H G V H U Y L F H V
, Q F U H D V H G Z H D U R U G D P D J H W R F H U W D L Q
S D U W V F D Q U H V X O W I U R P I D L O X U H W R S H U
I R U P U H T X L U H G V H U Y L F H V D W W K H S U R S H U
P L O H D J H L Q W H U Y D O V
( ; $ 0 3 / (
Page 80 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
: D U Q L Q J D Q G , Q G L F D W R U / L J K W VNOTE:
If warning and indicator lights blink or
come on, the corresponding messages
may be shown on the information display.
% U D N H 6 \ V W H P : D U Q L Q J / L J K W
65D477
Three different types of operations exist
depending on the vehicle’s specification.
1) The light comes on briefly when the
ignition switch is turned to the “ON”
position or the engine switch is pressed
to change the ignition mode to “ON”.
2) The light comes on when the parking
brake is engaged with the ignition
switch in the “ON” position or the igni-
tion mode “ON”.
3) The light comes on when under either
or both of above two conditions.
The light also comes on when the fluid in
the brake fluid reservoir falls below the
specified level.
The light should go out after starting the
engine and fully releasing the parking
brake, if the fluid level in the brake fluid
reservoir is adequate.
If your vehicle is equipped with the ABS,
the brake system warning light also comes
on together with the ABS warning light
when the rear brake force control function(proportioning valve function) of the ABS
system fails.
If the brake system warning light comes on
while you are driving the vehicle, it may
mean that there is something wrong with
the vehicle’s brake system. If this happens,
you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting and
stopping on the shoulder of the road.
3)If you determine that it is safe, drive
cautiously at low speed to the nearest
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
repairs, or
4) Have the vehicle towed to the nearest
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
repairs.
: $ 5 1 , 1 *
5 H P H P E H U W K D W V W R S S L Q J G L V W D Q F H
P D \ E H O R Q J H U \ R X P D \ K D Y H W R S X V K
K D U G H U R Q W K H S H G D O D Q G W K H S H G D O
P D \ J R G R Z Q I D U W K H U W K D Q Q R U P D O
Page 81 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
NOTE:
Because the brake system is self-adjust-
ing, the fluid level will drop as the brake
pads become worn. Replenishing the
brake fluid reservoir is considered normal
periodic maintenance.
NOTE:
(Parking Brake Reminder Buzzer)
A buzzer sounds intermittently to remind
you to release the parking brake if you
start the vehicle without releasing the park-
ing brake. Make sure that the parking
brake is fully released and the brake sys-
tem warning light turns off.
$ Q W L / R F N % U D N H 6 \ V W H P $ % 6
: D U Q L Q J / L J K W L I H T X L S S H G
65D529
When the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
“ON”, the light comes on briefly so you can
check that the light is working.
If the light stays on, or comes on when
driving, there may be something wrong
with the ABS.
If this happens:
1) Pull off the road and stop carefully.
2) Turn the ignition switch to “LOCK” or
change the ignition mode to “LOCK”
(OFF) by pressing the engine switch
and then start the engine again.
If the warning light comes on briefly then
turns off, the system is normal. If the warn-
ing light still stays on.
If the light and the brake system warning
light stay on, or come on simultaneously
when driving, your ABS system is
equipped with the rear brake force control
function (proportioning valve function) andthere may be something wrong with both
the rear brake force control function and
anti-lock function of the ABS system.
If one of these happens, have the system
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
If the ABS becomes inoperative, the brake
system will function as an ordinary brake
system that does not have this ABS sys-
tem.
For details of ABS system, refer to “Anti-
Lock Brake System (ABS)” in the “OPER-
ATING YOUR VEHICLE” section.
: $ 5 1 , 1 *
, I D Q \ R I W K H I R O O R Z L Q J F R Q G L W L R Q V
R F F X U \ R X V K R X O G L P P H G L D W H O \ D V N
\ R X U D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N
V K R S W R L Q V S H F W W K H E U D N H V \ V W H P
G R H V Q R W J R R X W D I W H U W K H H Q J L Q H
K D V E H H Q V W D U W H G D Q G W K H S D U N L Q J
E U D N H K D V E H H Q I X O O \ U H O H D V H G
Page 82 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
2 L O 3 U H V V X U H / L J K WThis light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to “ON”, and goes out when
the engine is started. The light will come
on and remain on if there is insufficient oil
pressure. If the light comes on when driv-
ing, pull off the road as soon as you can
and stop the engine.
& K D U J L Q J / L J K W
50G052
This light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to “ON”, and goes out when
the engine is started. The light will come on
and remain on if there is something wrong
with the battery charging system. If the light
comes on when the engine is running, the
charging system should be inspected
immediately by your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S.
' U L Y H U
Page 83 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
$ L U % D J / L J K W
63J030
This light blinks or comes on for several
seconds when the ignition switch is turned
to the “ON” position or the engine switch is
pressed to change the ignition mode to
“ON” so you can check if the light is work-
ing.The light will come on and stay on if there
is a problem in the air bag system or the
seat belt pretensioner system (if
equipped).
0 D O I X Q F W L R Q , Q G L F D W R U / L J K W
65D530
Your vehicle has a computer-controlled
emission control system. A malfunction
indicator light is provided on the instrument
panel to indicate when it is necessary to
have the emission control system serviced.
The malfunction indicator light comes on
when the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
“ON” to let you know the light is working
and goes out when the engine is started.
If the malfunction indicator light comes on
or blinks when the engine is running, there
is a damage in the emission control sys-
tem.
Bring the vehicle to your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S to have the damage fixed.
, P P R E L O L ] H U . H \ O H V V 3 X V K 6 W D U W
6 \ V W H P : D U Q L Q J / L J K W
80JM122
When the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON, the light comes on briefly so you can
check that the light is working. If this light
stays on, there is a problem with the sys-
tem. Ask your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S to have the system inspected.
: $ 5 1 , 1 *
, I W K H $ , 5 % $ * O L J K W G R H V Q R W E O L Q N R U
F R P H R Q E U L H I O \ Z K H Q W K H L J Q L W L R Q
V Z L W F K L V W X U Q H G W R W K H
Page 84 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
2 S H Q ' R R U : D U Q L Q J / L J K W
54G391
This light remains on until all doors (includ-
ing the tailgate) are completely closed.
If any door (including the tailgate) is open
when the vehicle is moving, a ding sounds
to remind you to close all doors completely.
/ R Z ) X H O : D U Q L Q J / L J K W
54G343
If this light comes on, fill the fuel tank
immediately.
When this light comes on, a ding sounds
once to remind you to fill the fuel.
If you do not fill the fuel, a ding sounds
every time when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition
mode to ON.
NOTE:
The activation point of this light varies
depending on road conditions (for exam-
ple, slope or curve) and driving conditions
because of fuel moving in the tank.
( O H F W U L F 3 R Z H U 6 W H H U L Q J / L J K W
79J039
This light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to ON, and goes out when
the engine is started.
If this light comes on or blinks while driv-
ing, the power steering system may not
work properly. Have the system inspected
by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
NOTE:
While parking or driving at very low speed
greater steering effort is required. This is
not a malfunction of the steering system
but power steering control system limiting
power assist in order to prevent it from
over heating.
• The steering wheel is operated very
often.
• The steering wheel is kept in a fully
turned position for a long while.
When the power steering control system
cools down, the power steering system is
restored back to the original condition.
Page 86 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
0 D L Q % H D P K L J K E H D P , Q G L F D W R U
/ L J K W
50G056
This indicator comes on when headlight
main beams (high beams) are turned on.
, O O X P L Q D W L R Q , Q G L F D W R U / L J K W
64J045
This indicator light comes on while the posi-
tion lights, tail light and/or the headlights are
on.
* O R Z 3 O X J , Q G L F D W R U / L J K W
60A543
If the coolant temperature is cool enough, this
light comes on when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition mode
to ON and goes out when the glow plug is
heated enough for engine starting.
Page 87 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
) X H O ) L O W H U : D U Q L Q J / L J K W
60A541
This light comes on for several seconds
when the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to ON
so you can check that light is working.
If the light comes on when driving, there is a
possibility to have water in the fuel filter.
Drain water as soon as possible.Have your
vehicle inspected by an D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S. For details of drain-ing
water, refer to “Fuel Filter” in the
³ , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & ( ´ sec-
tion.
0 D V W H U : D U Q L Q J , Q G L F D W R U / L J K W
78K049
When the information display shows warn-
ing and indicator messages, this indicator
light may also blink.
For details, refer to “Information Display” in
this section.
/ L J K W L Q J & R Q W U R O / H Y H U
65D611
: $ 5 1 , 1 *
7 R D Y R L G S R V V L E O H L Q M X U \ G R Q R W R S H U
D W H F R Q W U R O V E \ U H D F K L Q J W K U R X J K W K H
V W H H U L Q J Z K H H O