light SUZUKI NEXA 2015 1.G Manual Online
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2015, Model line: NEXA, Model: SUZUKI NEXA 2015 1.GPages: 288, PDF Size: 8.02 MB
Page 249 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
6 L G H 7 X U Q 6 L J Q D O / L J K W L I H T X L S S H G
76MH0A006
1) Remove the light housing (1) by sliding
to left with your finger.
76MH0A007
2) Turn the bulb holder (2) clockwise and
pull it out from the light housing.
76MH0A008
(4) Removal
(5) Install
3) To remove and install the bulb of the
turn signal light (3), simply pull out or
push in the bulb.
) U R Q W 7 X U Q 6 L J Q D O / L J K W
) U R Q W 3 R V L W L R Q / L J K W (Vehicle with the halogen headlights)
61MM0A030
(1)
(2)
(3)
(4)
(5)
(2)
(1)
Page 250 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
61MM0B077
1) Open the engine hood. To remove the
bulb holder of the front turn signal light
(1) or the front position light (2) from the
light housing, turn the holder counter-
clockwise and pull it out.
61MM0B078
(3) Removal
(4) Install
2) To remove the bulb of the front turn sig-
nal light (1) from the bulb holder, push in
the bulb and turn it counterclockwise. To
install a new bulb, push it in and turn it
clockwise.
To remove and install the bulb of the
front position light (2), simply pull out or
push in the bulb.
9 H K L F O H Z L W K W K H G L V F K D U J H K H D G O L J K W V
61MM0A091
To replace the bulb of the front turn signal
light (1), follow the procedure for the front
turn signal light bulb replacement of the
vehicle with the halogen headlights.NOTE:
Position function in discharge headlamp is
LED type, which is non replaceable.
(2)(1)
(2)
(1) (3)
(4)
( ; $ 0 3 / (
(1)
Page 251 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
) U R Q W ) R J / L J K W L I H T X L S S H G 1) Start the engine. Turn the steering wheel
to rotate the tires to the opposite side of
the fog light that requires replacement.
Then turn off the engine.
61MM0B079
2) Remove the screws (1).
61MM0B080
3) Remove the clips (2) by prying it off with
a flat blade screwdriver as shown in the
illustration.
61MM0B081
4) Open the end of the cover inside the
fender.
80JM071
5) Disconnect the coupler by pushing the
lock release. Turn the bulb holder coun-
terclockwise and remove it.
(1)
( ; $ 0 3 / (
(2)
( ; $ 0 3 / ( ( ; $ 0 3 / (
( ; $ 0 3 / (
Page 252 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
5 H D U & R P E L Q D W L R Q / L J K W
61MM0B082
1) Remove the bolts (1) and pull the light
housing (2) straight.
61MM0B083
2) To remove the bulb holder of the rear
turn signal light (3) or the tail/brake light
(4) from the light housing, turn the
holder counterclockwise and pull it out.
61MM0B084
(5) Removal
(6) Install3) To remove the bulb of the rear turn sig-
nal light (3) or the tail/brake light (4) from
bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
(2)(1)
(3)(4)
(3) / (4)
(5)
(6)
( ; $ 0 3 / (
Page 253 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
61MM0B085
NOTE:
When reinstalling the light housing, make
sure the clips are properly attached.
5 H Y H U V L Q J / L J K W
61MM0B088
1) Open the tailgate. Remove the clips (1)
by prying it off with a flat blade screw-
driver as shown in the illustration. Then,
pull out the trim (2).
61MM0B089
2) Disconnect the coupler (3) by pushing
the lock release. Turn the bulb holder ofthe reversing light (4) counterclockwise
and remove it.
61MM0B090
(5) Removal
(6) Install3) To remove and install the bulb of the
reversing light (4), simply pull out or
push in the bulb.
(2)
(1)
(3)
(4)
(4)
(5)
(6)
( ; $ 0 3 / (
Page 254 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
/ L F H Q V H 3 O D W H / L J K W
61MM0B086
1) Turn the cover (1) counterclockwise to
remove it.
61MM0B087
2) To remove and install the bulb of the
license plate light (2), simply pull out or
push in the bulb.
+ L J K P R X Q W 6 W R S / L J K W
80J100
1) Open the tailgate, and remove the nuts
(1) as shown in the illustration.
(1)
(2)
(1)
( ; $ 0 3 / (
Page 255 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
63J127
2) Close the tailgate. Remove the high-
mount stop light housing (2) from the
tailgate.
68KS063
3) Remove the bulb holder as shown in
the illustration.
76MH0A128
(4) Removal
(5) Install
4) To remove and install the bulb of the
high-mount stop light (3), simply pull out
or push in the bulb.
(2) ( ; $ 0 3 / (
( ; $ 0 3 / (
(3)
(4)
(5)
( ; $ 0 3 / (
Page 257 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
* O R Y H % R [ / L J K W L I H T X L S S H G
Since special procedures are required, we
recommend you take your vehicle to your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for bulb
replacement.
61M0108
1) Press inward on both side of the glove
box to unclamp it.
61M0109
2) Push the damper (1) (if equipped) right-
ward to remove the grove box.
64MS096
3) To remove and install the bulb of the
glove box light (2), simply pull out or
push in the bulb.
: L S H U % O D G H V
54G129
If the wiper blades become brittle or dam-
aged, or make streaks when wiping,
replace the wiper blades.
To install new wiper blades, follow the pro-
cedures below.
NOTE:
Some wiper blades may be different from
the ones described here depending on
vehicle specifications. If so, consult your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
proper replacement method.
( ; $ 0 3 / (
( ; $ 0 3 / (
(1)
(2)
( ; $ 0 3 / (
NOTICE
7 R D Y R L G V F U D W F K L Q J R U E U H D N L Q J W K H
Z L Q G R Z G R Q R W O H W W K H Z L S H U D U P
V W U L N H W K H Z L Q G R Z Z K L O H U H S O D F L Q J W K H
Z L S H U E O D G H
Page 261 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
$ L U & R Q G L W L R Q L Q J 6 \ V W H PIf you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain opti-
mum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine
idling. This circulates the refrigerant and oil
and helps protect the internal components. 5 H S O D F H P H Q W R I W K H $ L U & R Q G L W L R Q H U
) L O W H U L I H T X L S S H G Since special procedures are required, we
recommend you take your vehicle to your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for the
air conditioner filter replacement.
1) To access the air conditioner filter,
remove the glove box. Refer to the pro-
cedure for the bulb replacement of the
“Glove Box Light” in this section.
79MH0761
2) Remove the cover (1) and pull out the
air conditioner filter (2).
NOTE:
When you install a new filter, make sure
the UP mark (3) faces upward.
(1)
(2)
(3)
Page 268 of 288
Downloaded from www.Manualslib.com manuals search engine ( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
- X P S V W D U W L Q J L Q V W U X F W L R Q V
: K H Q - X P S 6 W D U W L Q J < R X U 9 H K L F O H
8 V H W K H ) R O O R Z L Q J 3 U R F H G X U H 1) Use only a 12-volt battery to jump start
your vehicle. Position the good 12-volt
battery close to your vehicle so that the
jump leads will reach both batteries.
When using a battery installed on
another vehicle, DO NOT LET THE
VEHICLES TOUCH. Set the parking
brakes fully on both vehicles.
2) Turn off all vehicle accessories, except
those necessary for safety reasons (for
example, headlights or hazard lights).
54MN259
3) Make jump lead connections as follows:
1. Connect one end of the first jump
lead to the positive (+) terminal of the
flat battery (1).
2. Connect the other end to the positive
(+) terminal of the booster battery (2).
3. Connect one end of the second jump
lead to the negative (–) terminal of the
booster battery (2).
4. Make the final connection to an
unpainted, heavy metal part (i.e.
engine mount bracket (3)) of the
engine of the vehicle with the flat bat-
tery (1).
: $ 5 1 , 1 *