Obs SUZUKI SWIFT 2000 1.G SF310 Service User Guide

6A
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-1
SECTION 6A
ENGINE MECHANICAL
(G10, 1-CAM 6-VALVES ENGINE)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
For the descriptions (items) not found in this section, refer to the same section of Service Manual men-
tioned in FOREWORD of this manual.
CONTENTS
ON-VEHICLE SERVICE6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Vacuum Check6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Check6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head Cover6A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body and Intake Manifold 6A- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold6A- 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt and Belt Tensioner 6A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft and Hydraulic Valve Lash Adjuster 6A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Lash Adjuster Noise Diagnosis 6A-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valves and Cylinder Head6A-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pistons, Piston Rings, Connecting Rods and Cylinders 6A-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR OVERHAUL6A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Assembly6A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Bearings, Crankshaft and Cylinder Block 6A-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6A-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS6A-31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6A1
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-1
SECTION 6A1
ENGINE MECHANICAL
(G13B, 1-CAM 16-VALVES ENGINE)
WARNING:
For vehicles equipped with Supplement Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either or these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION6A1- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine6A1- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication6A1- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Block6A1- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft and Main Bearings 6A1- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pistons, Rings, Piston Pins and Connecting Rods 6A1- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Value Train 6A1- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON VEHICLE SERVICE6A1- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compression Check6A1- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Vacuum Check6A1- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Check6A1- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Lash (Clearance)6A1- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cleaner Element6A1-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cleaner Outlet Hose6A1-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head Cover6A1-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body and Intake Manifold 6A1-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold6A1-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt and Belt Tensioner 6A1-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan and Oil Pump Strainer 6A1-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump6A1-28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rocker Arms, Rocker Arm Shaft and Camshaft 6A1-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valves and Cylinder Head6A1-41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Piston, Piston Rings, Connecting Rods and Cylinders 6A1-54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR OVERHAUL6A1-64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Assembly6A1-64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Bearings, Crankshaft and Cylinder Block 6A1-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6A1-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS6A1-81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS6A1-82 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE:
For what each abbreviation stands for (i.e., full term), refer to SECTION 0A.

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-59
Crank Pin and Connecting Rod Bearings

Inspect crank pin for uneven wear or damage. Measure crank pin
for out-of-round or taper with a micrometer. If crank pin is dam-
aged, or out-of-round or taper is out of limit, replace crankshaft or
regrind crank pin to undersize and use undersize bearing.
Connecting rod bearing size
Crank pin diameter
Standard41.982 – 42.000 mm
(1.6528 – 1.6535 in.)
0.25 mm (0.0098 in.)41.732 – 41.750 mm
(1.6430 – 1.6437 in.)
Out-of-round and taper limit: 0.01 mm (0.0004 in.)

Rod bearing:
Inspect bearing shells for signs of fusion, pitting, burn or flaking
and observe contact pattern. Bearing shells found in defective
condition must be replaced.
Two kinds of rod bearing are available; standard size bearing and
0.25 mm undersize bearing. To distinguish them, 0. 25 mm under-
size bearing has the stamped number (US025) on its backside as
indicated in figure, but standard size one has no number.

Rod bearing clearance:
1) Before checking bearing clearance, clean bearing and crank
pin.
2) Install bearing in connecting rod and bearing cap.
3) Place a piece of gaging plastic (1) to full width of crankpin as
contacted by bearing (parallel to crankshaft), avoiding oil hole.
4) Install rod bearing cap (1) to connecting rod.
When installing cap, be sure to point arrow mark (2) on cap to
crankshaft pulley side (3), as shown in figure. After applying
engine oil to rod bolts, tighten cap nuts to specified torque. DO
NOT turn crankshaft with gaging plastic installed.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-1
GENERAL DESCRIPTION6E1- 2 . . . . . . . . . . . . . .
AIR AND FUEL DELIVERY SYSTEM 6E1- 4. . . . .
ELECTRONIC CONTROL SYSTEM 6E1- 5. . . . . .
ON-VEHICLE SERVICE6E1- 8 . . . . . . . . . . . . . . . .
General 6E1- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accelerator Cable Adjustment 6E1- 8. . . . . . . . . .
Idle Speed Inspection 6E1- 8. . . . . . . . . . . . . . . . .
AIR AND FUEL DELIVERY SYSTEM 6E1- 9. . . . .
Fuel Pressure 6E1- 9. . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump 6E1-11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body 6E1-12. . . . . . . . . . . . . . . . . . . . . . . .
Fuel injector 6E1-15. . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E1-17. . . . . .
ECM 6E1-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAP Sensor 6E1-18. . . . . . . . . . . . . . . . . . . . . . . . .
TP Sensor 6E1-19. . . . . . . . . . . . . . . . . . . . . . . . . . .
IAT Sensor 6E1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
ECT Sensor 6E1-21. . . . . . . . . . . . . . . . . . . . . . . . .
Heated Oxygen Sensor -1 and -2 6E1-23. . . . . . .
Vehicle Speed Sensor 6E1-24. . . . . . . . . . . . . . . . .
Fuel Level Sensor (Gauge) 6E1-24. . . . . . . . . . . . Crankshaft Position Sensor 6E1-25. . . . . . . . . . . .
Main Relay 6E1-25. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump Relay 6E1-26. . . . . . . . . . . . . . . . . . . . .
Fuel Injector Resistor 6E1-26. . . . . . . . . . . . . . . . .
Fuel Cut Operation 6E1-26. . . . . . . . . . . . . . . . . . .
ISC System 6E1-26. . . . . . . . . . . . . . . . . . . . . . . . . .
ISC Actuator 6E1-27. . . . . . . . . . . . . . . . . . . . . . . . .
CTP Switch 6E1-28. . . . . . . . . . . . . . . . . . . . . . . . . .
ISC Actuator Relay 6E1-29. . . . . . . . . . . . . . . . . . .
EFE Heater Control System 6E1-29. . . . . . . . . . . .
EFE Heater 6E1-29. . . . . . . . . . . . . . . . . . . . . . . . . .
EFE Heater Relay 6E1-30. . . . . . . . . . . . . . . . . . . .
Radiator Fan Control System 6E1-30. . . . . . . . . .
Radiator Fan Control Relay 6E1-31. . . . . . . . . . . .
Radiator Fan 6E1-31. . . . . . . . . . . . . . . . . . . . . . . . .
EMISSION CONTROL SYSTEM 6E1-32. . . . . . . . .
EVAP Control System 6E1-32. . . . . . . . . . . . . . . . .
PCV System 6E1-34. . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6E1-36 . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS6E1-36 . . . . . . . . . . . . . . . . . . . .
SECTION 6E1
ENGINE AND EMISSION CONTROL SYSTEM
(TBI FOR G10)
WARNING:
For vehicles equipped with a Supplemental Inflatable Restraint Air Bag System:

Service on or around Air Bag System Components or Wiring must be performed only by an authorized
Suzuki dealer. Please observe all WARNINGS and SERVICE PRECAUTIONS in Section 9J under “On-
Vehicle Service” and the Air Bag System Component and Wiring Location view in Section 9J before
performing service on or around Air Bag System Components or Wiring. Failure to follow WARNINGS
could result in unintended air bag deployment or could render the air bag inoperative. Either of these
two conditions may result in severe injury.

SDM can maintain sufficient voltage to cause a deployment of air bags for up to 15 seconds after igni-
tion switch is turned to “LOCK” position, battery is disconnected or fuse powering SDM is removed.
Work must be started after 15 seconds from the time.
NOTE:
For the descriptions for vehicle without warm up three way catalytic converter (WU TWC), refer to the same
section of the Service Manual mentioned in the FOREWORD of this manual.
CONTENTS

6E1-20 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
1. Plunger
2. Throttle lever screw
2) Check to make sure that plunger of ISC actuator and throttle le-
ver screw are not in contact with each other. If they are, warm
up engine.
3) Loosen TP sensor screws.
a) Connect SUZUKI scan tool to DLC with ignition switch OFF.
b) Select “Data List” mode on SUZUKI scan tool.
c) Observe TP sensor voltage.
4) Turn TP sensor clockwise or counterclockwise and tighten TP
sensor screw at a position where voltage as specified below is
obtained.
TP sensor voltage when lever-to-stop
screw clearance is 3.5 mm (0.14 in.) : 0.98 – 1.02 V
Tightening Torque
(a): 2.0 N
.m (0.20 kg-m, 1.5 lb-ft)
5) Install ECM and connect couplers securely.
INTAKE AIR TEMPERATURE SENSOR (IAT SENSOR)
REMOVAL
1) Disconnect battery negative cable at battery.
2) Disconnect coupler from IAT sensor.
3) Remove IAT sensor and gasket from air cleaner case.

6E1-34 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
1. Tank pipe
2. Purge pipe
3. Air pipe
4. Blow air
1. Tank pressure
control valve
2. Orange side3. Black side
4. To canister
5. From fuel tank
EVAP CANISTER INSPECTION
WARNING:
DO NOT SUCK nozzles on EVAP canister. Fuel vapor inside
EVAP canister is harmful.
1) Disconnect vacuum hoses from EVAP canister and remove
EVAP canister.
2) When air is blown into tank pipe, there should be no restriction
of flow through purge pipe and air pipe.
If operation differs from above description, EVAP canister must
be replaced.
3) Install EVAP canister and connect hoses to canister.
TANK PRESSURE CONTROL VALVE INSPECTION
WARNING:
DO NOT SUCK air through tank pressure control valve.
Fuel vapor inside the valve is harmful.
1) Remove tank pressure control valve.
2) Air should pass through valve smoothly from fuel tank side
(black side of tank pressure control valve) to orange side when
blown hard.
3) From orange side, even when blown softly, air should come out
of black side.
4) If air doesn’t pass though valve in step 2) or hard blow is required
in step 3), replace tank pressure control valve.
5) Install tank pressure control valve.
NOTE:
When connecting tank pressure control valve between
hoses, refer to figure at the left for installing direction.
PCV SYSTEM
NOTE:
Be sure to check that there is no obstruction in PCV valve or
its hoses before adjusting engine idle speed, for obstructed
PCV valve or hose hampers its accurate adjustment.
PCV HOSE INSPECTION
Check hoses for connection, leakage, clog and deterioration.
Replace as necessary.

6E2
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-1
GENERAL DESCRIPTION6E2- 2 . . . . . . . . . . . . . .
AIR INTAKE SYSTEM 6E2- 6. . . . . . . . . . . . . . . . . .
FUEL DELIVERY SYSTEM 6E2- 7. . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E2- 8. . . . . .
Engine and Emission Control Input /
Output Table 6E2- 9. . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSISSee Section 6. . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE6E2-13 . . . . . . . . . . . . . . . .
Accelerator Cable Adjustment 6E2-13. . . . . . . . . .
Idle Speed/Idle Air Control (IAC)
Duty Inspection 6E2-14. . . . . . . . . . . . . . . . . . . . .
AIR INTAKE SYSTEM 6E2-15. . . . . . . . . . . . . . . . . .
Throttle Body 6E2-15. . . . . . . . . . . . . . . . . . . . . . . .
Idle Air Control Valve 6E2-17. . . . . . . . . . . . . . . . .
FUEL DELIVERY SYSTEM 6E2-18. . . . . . . . . . . . . .
Fuel Pressure Inspection 6E2-18. . . . . . . . . . . . . .
Fuel Pump 6E2-21. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pressure Regulator 6E2-22. . . . . . . . . . . . . . .
Fuel Injector 6E2-23. . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E2-27. . . . . .
ECM / PCM 6E2-27. . . . . . . . . . . . . . . . . . . . . . . . . .
MAP Sensor 6E2-27. . . . . . . . . . . . . . . . . . . . . . . . .
TP Sensor 6E2-28. . . . . . . . . . . . . . . . . . . . . . . . . . .
IAT Sensor 6E2-29. . . . . . . . . . . . . . . . . . . . . . . . . .
ECT Sensor 6E2-30. . . . . . . . . . . . . . . . . . . . . . . . . Heated Oxygen Sensor -1 and -2 6E2-31. . . . . . .
Camshaft Position Sensor 6E2-32. . . . . . . . . . . . .
Crankshaft Position Sensor 6E2-32. . . . . . . . . . . .
Vehicle Speed Sensor 6E2-33. . . . . . . . . . . . . . . . .
Fuel Level Sensor (gauge) 6E2-33. . . . . . . . . . . . .
Main Relay, Fuel Pump Relay and
Radiator Fan Control Relay 6E2-33. . . . . . . . . . .
Fuel Cut Operation (Inspection) 6E2-34. . . . . . . .
Radiator Fan Control System 6E2-34. . . . . . . . . .
System Inspection 6E2-34. . . . . . . . . . . . . . . . . .
Radiator Fan 6E2-34. . . . . . . . . . . . . . . . . . . . . . .
EMISSION CONTROL SYSTEM 6E2-35. . . . . . . . .
EGR System 6E2-35. . . . . . . . . . . . . . . . . . . . . . . . .
EVAP Control System 6E2-36. . . . . . . . . . . . . . . . .
EVAP Canister Purge Inspection 6E2-36. . . . . .
Vacuum Passage Inspection 6E2-37. . . . . . . . .
Vacuum Hose Inspection 6E2-37. . . . . . . . . . . .
EVAP Canister Purge Valve
Inspection 6E2-37. . . . . . . . . . . . . . . . . . . . . . . .
EVAP Canister Inspection 6E2-38. . . . . . . . . . .
PCV System 6E2-38. . . . . . . . . . . . . . . . . . . . . . . . .
PCV Hose Inspection 6E2-38. . . . . . . . . . . . . . .
PCV Valve Inspection 6E2-38. . . . . . . . . . . . . . .
SPECIAL TOOLS6E2-39 . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS6E2-39 . . . . . . . . . . . . . . . . . . . . .
SECTION 6E2
ENGINE AND EMISSION CONTROL SYSTEM
(SFI FOR G13)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

6E2-38 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
EVAP Canister Inspection
WARNING:
DO NOT SUCK nozzles on EVAP canister. Fuel vapor inside
EVAP canister is harmful.
1) Check outside of EVAP canister visually.
2) Disconnect vacuum hoses from EVAP canister.
3) Check that there should be no restriction of flow through purge
pipe (2) and air pipe (3) when air is blown (4) into tank pipe (1).
If any faulty condition is found in above inspection replace.
PCV SYSTEM
NOTE:
Be sure to check that there is no obstruction in PCV valve or
its hoses before checking IAC duty, for obstructed PCV valve
or hose hampers its accurate adjustment.
PCV Hose Inspection
Check hoses for connection, leakage, clog and deterioration.
Replace as necessary.
PCV Valve Inspection
1) Disconnect PCV valve (1) from cylinder head cover and install
plug to head cover hole.
2) Run engine at idle.
3) Place your finger over end of PCV valve (1) to check for vacuum.
If there is no vacuum, check for clogged valve. Replace as nec-
essary.
4) After checking vacuum, stop engine and remove PCV valve (1).
Shake valve and listen for the rattle of check needle inside the
valve. If valve does not the rattle, replace valve.
5) After checking, remove plug and install PCV valve (1).

6F
IGNITION SYSTEM 6F-1
GENERAL DESCRIPTION6F- 1 . . . . . . . . . . . . . .
DIAGNOSIS6F- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE6F- 5 . . . . . . . . . . . . . . . .
Ignition Spark Test 6F- 5. . . . . . . . . . . . . . . . . . . .
High-Tension Cords 6F- 5. . . . . . . . . . . . . . . . . . .
Spark Plugs 6F- 6. . . . . . . . . . . . . . . . . . . . . . . . .
Noise Suppressor 6F- 6. . . . . . . . . . . . . . . . . . . . Ignition Coil 6F- 7. . . . . . . . . . . . . . . . . . . . . . . . . .
Igniter 6F- 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor 6F- 8. . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Timing 6F- 9. . . . . . . . . . . . . . . . . . . . . . .
Distributor Unit 6F-10. . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6F-11 . . . . . . . . . . . . . . . . . . . . . .
The ignition system used for this vehicle has an elec-
tronic ignition control system and consists of the fol-
lowing parts.

ECM
It detects the engine condition through the signals
from the sensors, determines the most suitable igni-
tion timing and time for electricity to flow to the pri-
mary coil and sends a signal to the power unit.

Power unit (Igniter)
It turns ON and OFF the primary current of the igni-
tion coil according to the signal from ECM.

Ignition coil
When the ignition coil primary current is turned OFF,
a high voltage is induced in the secondary winding.

Distributor
It distributes a high voltage current to each plug.
High-tension cords and spark plugs.

CMP sensor (Camshaft position Sensor)
Located in the distributor, it converts the crank angle
into voltage variation and sends it to ECM. For its
details, refer to Section 6E1.

TP sensor, ECT sensor and MAP sensor
For their details, refer to Section 6E.
In electronic ignition control system, the ECM is pro-
grammed for the best ignition timing under every en-
gine condition. Receiving signals which indicate the
engine condition from the sensors, e.g., engine revo-
lution, intake air pressure, coolant temperature, etc.,
it selects the most suitable ignition timing from its
memory and operates the power unit.
Thus ignition timing is controlled to yield the best en-
gine performance.
For more information, refer to Section 6E1.
SECTION 6F
IGNITION SYSTEM
WARNING:
For vehicles equipped with a Supplemental Inflatable Restraint Air Bag System:

Service on or around Air Bag System Components or Wiring must be performed only by an authorized
Suzuki dealer. Please observe all WARNINGS and SERVICE PRECAUTIONS in Section 9J under “On-
Vehicle Service” and the Air Bag System Component and Wiring Location view in Section 9J before
performing service on or around Air Bag System Components or Wiring. Failure to follow WARNINGS
could result in unintended air bag deployment or could render the air bag inoperative. Either of these
two conditions may result in severe injury.

SDM can maintain sufficient voltage to cause a deployment of air bags for up to 10 seconds after igni-
tion switch is turned to “LOCK” position, battery is disconnected or fuse powering SDM is removed.
Work must be started after 15 seconds from the time.
CONTENTS
GENERAL DESCRIPTION

6F1
IGNITION SYSTEM (SFI FOR G13) 6F1-1
GENERAL DESCRIPTION6F1-2 . . . . . . . . . . . . . .
DIAGNOSIS6F1-3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE6F1-5 . . . . . . . . . . . . . . . .
Ignition Spark Test 6F1-5. . . . . . . . . . . . . . . . . . . .
High-Tension Cords 6F1-5. . . . . . . . . . . . . . . . . . . Spark Plugs 6F1-6. . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Coil Assembly 6F1-6. . . . . . . . . . . . . . . . .
Crankshaft Position Sensor 6F1-7. . . . . . . . . . . .
Ignition Timing 6F1-7. . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6F1-9 . . . . . . . . . . . . . . . . . . . . . .
SECTION 6F1
IGNITION SYSTEM
(SFI FOR G13)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS