power steering fluid SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

0A-22 GENERAL INFORMATION
A
ABS : Anti-Lock Brake System
ATDC : After Top Dead Center
API : American Petroleum Institute
ATF : Automatic Transmission Fluid
ALR : Automatic Locking Retractor
AC : Alternating Current
A / T : Automatic Transmission
A / C : Air Conditioning
ABDC : After Bottom Dead Center
A / F : Air Fuel Mixture Ratio
A-ELR : Automatic-Emergency Locking
Retractor
B
B+ : Battery Positive Voltage
BTDC : Before Top Dead Center
BBDC : Before Bottom Dead Center
C
CKT : Circuit
CMP Sensor : Camshaft Position Sensor
(Crank Angle Sensor, CAS)
CO : Carbon Monoxide
CPP Switch : Clutch Pedal Position Switch
(Clutch Switch, Clutch Start
Switch)
CPU : Central Processing Unit
CRS : Child Restraint System
D
DC : Direct Current
DLC : Data Link Connector (Assembly
Line Diag. Link, ALDL, Serial
Data Link, SDL)
DOHC : Double Over Head Camshaft
DOJ : Double Offset Joint
DRL : Daytime Running Light
DTC : Diagnostic Trouble Code
(Diagnostic Code)
E
EBCM : Electronic Brake Control
Module, ABS Control Module
ECM : Engine Control Module
ECT Sensor : Engine Coolant Temperature
Sensor (Water Temp. Sensor,
WTS)
EGR : Exhaust Gas Recirculation
EGRT Sensor : EGR Temperature Sensor
(Recirculated Exhaust
Gas Temp. Sensor, REGTS)
EFE Heater : Early Fuel Evaporation Heater
(Positive Temperature
Coefficient, PTC Heater)
ELR : Emergency Locking Retractor
EPS : Electronic Power Steering
EVAP : Evaporative Emission
EVAP Canister : Evaporative Emission Canister
(Charcoal Canister)
F
4WD : 4 Wheel Drive
G
GEN : Generator
GND : Ground
H
HC : Hydrocarbons
HO2S : Heated Oxygen Sensor
I
IAC Valve : Idle Air Control Valve (Idle
Speed Control Solenoid Valve,
ISC Solenoid Valve)
IAT Sensor : Intake Air Temperature Sensor
(Air temperature Sensor, ATS)
ICM : Immobilizer Control Module
IG : Ignition
ISC Actuator : Idle Speed Control Actuator
(Motor)
ABBREVIATIONS AND SYMBOLS MAY BE USED IN THIS MANUAL
ABBREVIATIONS

G (Base Color)
G (Base Color)
Y (Stripe Color)
0A-24 GENERAL INFORMATION
SYMBOLS
SYMBOLDEFINITIONSYMBOLDEFINITION
Tightening torqueApply SUZUKI BOND NO. 1216
99000-31160
Apply oil (Engine, transmission,
transfer, differential)Apply SILICONE SEALANT
99000-31120
Apply fluid (Brake, power steering or
automatic transmission fluid)Apply SEALING COMPOUND 366E
99000-31090
Apply SUZUKI SUPER GREASE A
99000-25010
Apply SUZUKI SUPER GREASE C
99000-25030Apply THREAD LOCK 1322
99000-32110
Apply SUZUKI SUPER GREASE E
99000-25050Apply THREAD LOCK 1333B
99000-32020
Apply SUZUKI SUPER GREASE H
99000-25120Apply THREAD LOCK 1342
99000-32050
Apply SUZUKI SUPER GREASE I
99000-25210
Apply SUZUKI BOND NO. 1215
99000-31110Do not reuse
Apply SUZUKI BOND NO. 1207C
99000-31150Note on reassembly
WIRE COLOR SYMBOLS
SymbolWire ColorSymbolWire Color
BBLKBlackO, OrORNOrange
BlBLUBlueRREDRed
BrBRNBrownWWHTWhite
GGRNGreenYYELYellow
GrGRYGrayPPNKPink
LblLT BLULight blueVPPLViolet
LgLT GRNLight green
There are two kinds of colored wire used in this vehicle. One is
single-colored wire and the other is dual-colored (striped) wire.
The single-colored wire uses only one color symbol (i.e. “G”).
The dual-colored wire uses two color symbols (i.e. “G/Y”). The first
symbol represents the base color of the wire (“G” in the figure) and
the second symbol represents the color of the stripe (“Y” in the fig-
ure).

MAINTENANCE AND LUBRICATION 0B-3
Interval:
This interval should be
judged by
This table includes services as scheduled up to 90,000 km (54,000 miles)
mileage. Beyond 90,000 km (54,000 miles), carry out the same services at
the same intervals respectively.
This interval should be judged by
odometer reading or months,Km(
1,000)153045607590g
whichever comes first.Miles(
1,000)91827364554
Months122436486072
4. EMISSION CONTROL SYSTEM
4-1.PCV (Positive Crankcase Ventilation)
ValveVehicle
without
O2S
––I––I
Vehicle
with O2S–––––I
4-2.Fuel evaporative emission control system–––––I
5. BRAKE
5-1.Brake discs and padsIIIIII
Brake drums and shoes–I–I–I
5-2.Brake hoses and pipes–I–I–I
5-3.Brake fluid–R–R–R
5-4.Brake lever and cableInspect at first 15,000 km (9,000 miles) only.
6. CHASSIS AND BODY
6-1.Clutch pedal (for manual transmission)–I–I–I
6-2.Tires/wheel discsIIIIII
6-3.Propeller shaft (4WD) and drive shafts––I––I
6-4.Suspension system–I–I–I
6-5.Steering system–I–I–I
6-6.Power steering (if equipped)IIIIII
6-7.Manual transmission oilI–R––R
6-8.Automatic transmissionFluid level–I–I–I
Fluid changeReplace every 165,000 km (99,000 miles).
Fluid hose–––R––
6-9.Rear differential oil (4WD) (R: 1st 15,000 km only)R or I–I–I–
6-10. All latches, hinges and locks–I–I–I
NOTES:

“R”: Replace or change

“I”: Inspect and correct or replace if necessary

1. Ball joint stud dust seal (boot)
2. Suspension arm
1. Tie-rod end boot
2. Steering gear case boot
3. Universal joint
0B-16 MAINTENANCE AND LUBRICATION

Check front and rear suspension systems for damaged, loose or
missing parts; also for parts showing signs of wear or lack of lu-
brication.
Repair or replace defective parts, if any.

Check front suspension arm ball joint stud dust seals for leakage,
detachment, tear or any other damage.
Replace defective boot, if any.
ITEM 6-5
Steering System Inspection
1) Check steering wheel for play and rattle, holding vehicle straight
on ground.
Steering wheel play “a”: 0 – 30 mm (0 – 1.1 in.)
2) Check steering linkage for looseness and damage. Repair or re-
place defective parts, if any.
3) Check boots of steering linkage and steering gear case for dam-
age (leaks, detachment, tear, etc.). If damage is found, replace
defective boot with new one.
4) Check universal joints of steering shaft for rattle and damage. If
rattle or damage is found, replace defective part with a new one.
ITEM 6-6
Power Steering (P / S) System Inspection (if equipped)
1) Visually check power steering system for fluid leakage and hose
for damage and deterioration.
Repair or replace defective parts, if any.
2) With engine stopped, check fluid level indicated on fluid tank,
which should be between MAX and MIN marks. If it is lower than
MIN, fill fluid up to MAX mark.
NOTE

Be sure to use specified P / S fluid.

Fluid level should be checked when fluid is cool.
3) Visually check pump drive belt for cracks and wear.
4) Check belt for tension, referring to item 1-1 in this section.
If necessary, adjust or replace.

MAINTENANCE AND LUBRICATION 0B-21
[Parking brake]
Check that lever has proper travel.
Check to ensure that parking brake is fully effective
when the vehicle is stopped on the safe slope and
brake lever is pulled all the way.
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to “HI” position and mode lever to
defroster position for this check. WARNING:
With vehicle parked on a fairly steep slope,
make sure nothing is in the way downhill to
avoid any personal injury or property damage.
Be prepared to apply regular brake quickly
even if vehicle should start to move.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSE, SF, SG, SH or SJ (Refer to engine oil viscosity chart in item 1-4.)
Engine coolantEthylene-glycol base coolant (“Antifreeze / Anticorrosion coolant”)
Brake fluidDOT3
Manual transmission oilSee SECTION 7A
Rear differential oilSee SECTION 7E
Automatic transmission fluidAn equivalent of DEXRON-IIE or DEXRON-III
Power steering fluidSee material table on SECTION 3B1
Door hingesEngine oil
Engine hood latchEngine oil
Key lock cylinderSpray lubricant