Timing SUZUKI SWIFT 2000 1.G SF310 Service Owner's Manual

1. Cylinder head cover
2. Gasket
3. Cylinder head
4. Camshaft housing No.1:
Apply sealant 99000-31110 to mating surface.
5. Camshaft housing No.2
6. Camshaft housing No.3:
Apply sealant 99000-31110 to mating surface.
7. Camshaft
8. Oil seal
9. Valve lash adjuster
10. Camshaft housing bolt
1. Crankshaft timing belt pulley: Tightening Torque
: Apply engine oil to sliding
: surfaces of each part.
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-15
CAMSHAFT AND HYDRAULIC VALVE LASH ADJUSTER
REMOVAL
1) Disconnect negative cable at battery.
2) Remove cylinder head cover as previously outlined.
3) Remove distributor and then its case from cylinder head.
4) Remove crankshaft pulley, timing belt outside cover and timing
belt as previously outlined.
After removing timing belt, set key (2) on crankshaft in position
as shown in figure by turning crankshaft. This is to prevent inter-
ference between valves and piston when reinstalling camshaft.
5) Remove camshaft timing belt pulley (1).
Lock camshaft (2) with a proper size rod (3) inserted into hole (10
mm, 0.39 in.) in it as shown and then loosen camshaft timing belt
pulley bolt.
NOTE:
Mating surfaces of cylinder head and cover must not be
damaged in this work. So, put clean shop cloth (4) between
rod and mating surfaces, and use care not to bump rod
against mating surfaces hard when loosening bolt.

Indicates position from timing belt
side. Install in numerical order
starting from timing belt side.

Indicates direction of housing.
Install so that arrow is directed
toward timing belt side.
6A-18 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
INSTALLATION
1) Before installing valve lash adjuster to cylinder head, fill oil pas-
sage of cylinder head (1) with engine oil according to the follow-
ing procedure.
Pour engine oil through camshaft journal oil holes (2) and check
that oil comes out from oil holes in sliding part of valve lash ad-
juster.
2) Install lash adjuster to cylinder head.
Apply engine oil around valve lash adjuster and then install it to
cylinder head.
3) Install camshaft to cylinder head.
After applying engine oil to camshaft journal and all around cam,
set camshaft to cylinder head so that camshaft timing belt pulley
pin hole (1) in camshaft is at lower position.
4) Install camshaft housing to camshaft and cylinder head.

Apply engine oil to sliding surface of each housing against
camshaft journal.

Apply sealant to mating surface of No.1 and No.3 housings
which will mate with cylinder head.
“A”: Sealant 99000-31110

Embossed marks are provided on each camshaft housing, in-
dicating position and direction for installation.
Install housing as indicated by these marks.

2. No.2 housing
3. No.3 housing
3. Rod
4. Shop cloth
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-19

As camshaft housing No.1 (1) retains camshaft in proper
position as to thrust direction, make sure to first fit No.1 hous-
ing to No.1 journal of camshaft securely.

After applying engine oil to housing bolts, tighten them tem-
porarily first. Then tighten them by following sequence as
shown in figure.
Tighten a little at a time and evenly among bolts and repeat
tightening sequence three to four times before they are tight-
ened to specified torque.
Special Tool
(A): 09919-16010
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
5) Install camshaft oil seal.
After applying engine oil to oil seal lip, press-fit camshaft oil
seal till oil seal surface becomes flush with housing surface.
6) Install camshaft timing belt pulley (1) to camshaft (2) after
installing dwell pin to camshaft.
With locking camshaft as shown in figure, tighten pulley bolt to
specified torque.
Tightening Torque
(b): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
7) Install cylinder head cover to cylinder head as previously out-
lined.
8) Install timing belt, timing belt outside cover, crankshaft pulley,
water pump pulley and water pump belt as previously outlined.
9) Install distributor case and distributor.
Refer to Section 6F for installation.
10) Install air cleaner assembly as previously outlined.
11) Connect negative cable at battery.
12) Adjust ignition timing.
Refer to Section 6F for adjustment.

1. Cylinder block
2. Front oil seal
3. Main bearing
4. Bearing cap
5. Cap washer
6. Cap bolt
7. Timing pulley key
8. Crankshaft
9. Thrust bearing:
Set oil grooves of bearing to weds.
10. Rear oil seal
11. Pin
12. Oil seal housing gasket
13. Oil seal housing
14. Housing bolt
15. Input shaft bearing
16. Flywheel
17. Flywheel bolt
: Tightening Torque
: Do not reuse
: Apply engine oil to sliding
: surfaces of each part.
78 N.m (7.8 kg-m)
12 N
.m (1.2 kg-m)
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-27
MAIN BEARINGS, CRANKSHAFT AND CYLINDER BLOCK
REMOVAL
1) Remove engine with transmission from body as previously out-
lined.
2) Remove transmission from engine, and then remove clutch and
flywheel (drive plate for A / T).
3) Remove water pump belt, generator bracket, crankshaft pulley,
timing belt, and crankshaft timing belt pulley etc.
4) Remove cylinder head assembly.
5) Remove oil pan and oil pump strainer.
6) Remove pistons and connecting rods.
7) Remove oil pump and oil seal housing.
8) Remove main bearing caps and crankshaft.

ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-29
5) Install oil seal housing and its gasket.
Install new gasket. Do not reuse gasket removed in disassem-
bly. Oil lip portion of oil seal before installing. Tighten housing
bolts to specification.
After installing oil seal housing, gasket edges might bulge out;
if so, cut them off to make them flush with cylinder block and
oil seal housing.
Tightening Torque
(b): 12 N
.m (1.2 kg-m, 9.0 lb-ft)
6) Install oil pump.
Refer to item “Oil pump” for installation of oil pump.
7) Install flywheel (M / T model) or drive plate (A / T model).
Using special tool, lock flywheel and torque its bolts (1) to spec-
ification.
Special Tool
(A): 09924-17810
Tightening Torque
(c): 78 N
.m (7.8 kg-m, 56.5 lb-ft)
8) Install pistons and connecting rods as previously outlined.
9) Install oil pump strainer and oil pan.
10) Install cylinder head assembly to cylinder block (1).
Before installing cylinder head assembly to cylinder block,
install check valve (2) into oil gallery in cylinder block, directing
slit of valve toward top of cylinder block.
NOTE:
Tighten cylinder head bolts to specified torque as pre-
viously outlined.
Whenever installing cylinder head to new cylinder block,
use following procedure to tighten cylinder head bolts.

Tighten cylinder head bolts to specified torque as pre-
viously outlined and loosen them once till tightening
torque becomes “zero”. And then torque them to specifi-
cation again.
11) Install crankshaft timing belt pulley, timing belt, crankshaft
pulley, water pump pulley, etc., as previously outlined.
12) Install clutch to flywheel (M / T model).
For clutch installation, refer to Section 7C.
13) Install engine with transmission to body as previously outlined.

6A1
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-1
SECTION 6A1
ENGINE MECHANICAL
(G13B, 1-CAM 16-VALVES ENGINE)
WARNING:
For vehicles equipped with Supplement Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either or these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION6A1- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine6A1- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication6A1- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Block6A1- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft and Main Bearings 6A1- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pistons, Rings, Piston Pins and Connecting Rods 6A1- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Value Train 6A1- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON VEHICLE SERVICE6A1- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compression Check6A1- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Vacuum Check6A1- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Check6A1- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Lash (Clearance)6A1- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cleaner Element6A1-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cleaner Outlet Hose6A1-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head Cover6A1-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body and Intake Manifold 6A1-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold6A1-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt and Belt Tensioner 6A1-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan and Oil Pump Strainer 6A1-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump6A1-28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rocker Arms, Rocker Arm Shaft and Camshaft 6A1-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valves and Cylinder Head6A1-41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Piston, Piston Rings, Connecting Rods and Cylinders 6A1-54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR OVERHAUL6A1-64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Assembly6A1-64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Bearings, Crankshaft and Cylinder Block 6A1-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6A1-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS6A1-81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS6A1-82 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE:
For what each abbreviation stands for (i.e., full term), refer to SECTION 0A.

6A1-2 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
GENERAL DESCRIPTION
ENGINE
The engine is a water-cooled, in line 4 cylinders, 4 stroke cycle gasoline unit equipped with its S.O.H.C. (Single
Overhead Camshaft) valve mechanism arranged for “V”-type valve configuration and 16 valves (IN 2 and EX 2 / one
cylinder).
The single overhead camshaft is mounted over the cylinder head: it is driven from crankshaft through timing belt
and opens and closes its valves via the rocker arms.

2
IN
EX (A)
1
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-9
VALVE LASH (CLEARANCE)
1) Remove negative cable at battery.
2) Remove cylinder head cover referring to item “Cylinder Head
cover”.
3) Remove engine under cover of right side from body.
4) Using special tool and wrench (1), turn crankshaft pulley clock-
wise until “V” mark (2) (in white paint) on pulley aligns with “0”
(zero) calibrated on timing belt cover.
Special Tool
(A): 09919-16020
5) See if the rocker arms of No.1 cylinder are off the respective cam
lobes (of camshaft); if so, valves (1), (2), (5) and (7) in figure are
ready for clearance checking and adjustment. Check valve
lashes at valves (1), (2), (5) and (7).
If the rocker arms of No.4 cylinder are off the respective cam
lobes, check valve lashes at valves (3), (4), (6) and (8).
NOTE:
When checking valve clearance, insert thickness gauge be-
tween camshaft and cam-riding face of rocker arm.

1. Timing belt
2. Tensioner
3. Tensioner plate
4. Tensioner spring
5. Camshaft timing pulley
6. Tensioner bolt
7. Pulley bolt
8. Seal
9. Inside cover seal
10. Inside cover
11. Outside cover seal
12. Outside cover
13. Tensioner stud
14. Damper
1. Water pump pulley
: Tightening Torque
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-19
TIMING BELT AND BELT TENSIONER
REMOVAL
1) Disconnect negative cable at battery.
2) Remove right side of engine under cover.
3) Remove power steering pump belt or A / C compressor belt, if
equipped.
4) Disconnect IAT sensor at coupler.
5) Remove air cleaner case with air cleaner outlet hose.
6) Remove power steering hose stay (1) (if equipped).
7) Remove water pump pulley and drive belt.

1.“V” mark on cylinder
head cover
2. Timing mark by “E” on
camshaft timing belt pulley
3. Arrow mark on oil
pump case
4. Punch mark on crankshaft
timing belt pulley
4. Tensioner stud
6. Damper
6
6A1-20 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
8) Lock crankshaft inserting flat end rod or the like (2) between fly-
wheel ring gear and transmission case, after removing clutch
housing (torque converter housing for A / T) lower plate.
With crankshaft locked, remove crankshaft timing belt pulley
bolt (3).
9) Remove crankshaft pulley bolts (1).
10) Remove crankshaft pulley (4).
11) Install crankshaft timing belt pulley bolt temporarily to turn
crankshaft.
12) Release harness clamps.
13) Remove timing belt outside cover.
14) For installation of timing belt, align 4 timing marks as shown in
figure by turning crankshaft.
15) Remove timing belt tensioner (3), tensioner plate (2), tensioner
spring (5) and timing belt (1).