oil level SUZUKI SWIFT 2000 1.G SF310 Service Owner's Manual

7B-18 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

A / T fluid– – – – – level, leakage, color

A / T fluid hoses – – – – – disconnection, looseness, deterioration

Throttle cable – – – – – play, installation

A / T oil pressure control cable and select cable – – – – – installation

Engine oil – – – – – level, leakage

Engine coolant – – – – – level, leakage

Battery – – – – – fluid level, corrosion of terminal

Connectors of electric wire harness – – – – – disconnection, friction

Fuses – – – – – burning

Parts – – – – – installation, bolt – – – – – looseness

Parts – – – – – deformation

Other parts that can be checked visually
Also check following items at engine start, if possible.

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Other parts that can be checked visuallySection 0B
Section 7B
Section 6E1 or 6E2
Section 7B
Section 0B
Section 0B
Section 6 or 6-1
Section 8
Section 6 or 6-1
Section 6H
Section 8 (Section 6A or 6A1 for
pressure check)

ACCEPTABLE RANGE
1st gear (solenoids ON and ON)
2nd gear
(solenoids ON and OFF)
3rd gear
(solenoids OFF and OFF)
Vehicle speed
Engine speed
7B-28 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
DTC P0751 SHIFT SOLENOID-A (No.1) PERFORMANCE OR STUCK OFF
DTC P0756 SHIFT SOLENOID-B (No.2) PERFORMANCE OR STUCK OFF
CIRCUIT DESCRIPTION
PCM monitors throttle opening, engine speed, vehicle speed and gear position and compares the actual engine
speed and its specified value (i.e., engine speed obtained by PCM through calculation using the throttle open-
ing / gear position and vehicle speed).
DTC DETECTING CONDITION
POSSIBLE CAUSE

While running in “D” range after engine warmed up,
engine speed as compared with vehicle speed is not
within acceptable range.
2 driving cycle detection logic, continuous
monitoring.
A / T oil pressure control cable maladjusted

Selector cable maladjusted

Mechanical malfunction of shift solenoid valve
(stick or leakage)

Mechanical malfunction in transmission

Torque converter malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON and warm up engine to normal operating temperature.
3) Shift selector lever to “D” range.
4) Start vehicle and increase vehicle speed to 40 – 55 km / h ( 25 – 35 mile / h) by depressing accelerator pedal half
a stroke.
5) Keep vehicle at above speed for 5 sec. or longer.
6) Increase vehicle speed to 75 – 90 km / h (45 – 55 mile / h) by depressing accelerator pedal half a stroke and keep
it at that speed for 5 sec. or longer.
7) Stop vehicle and check pending DTC and DTC.

7B-32 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
STALL TEST
This test is to check overall performance of automatic transmission
and engine by measuring stall speed at D and R ranges.
Be sure to perform this test only when transmission fluid is at normal
operating temperature (70–80C / 158–176F) and its level is be-
tween FULL HOT and LOW HOT. (Refer to “Fluid level” in this sec-
tion.)
CAUTION:
Do not run engine at stall more than 5 seconds continuous-
ly, for oil temperature may rise excessively high.
1) Install tachometer.
2) Apply parking brake and block vehicle wheels.
3) Start engine with selector lever shifted to P range.
4) Depress brake pedal.
5) Shift selector lever to D range and depress accelerator pedal ful-
ly while watching tachometer. Read engine rpm quickly when it
has become constant (stall speed).
6) Release accelerator pedal immediately after stall speed is
checked.
7) In the same way, check stall speed at R range.
8) Stall speed should be within following specification.
Stall speed: 2,500 – 2,900 r / min
(For both G10 and G13 engine models)
9) Possible causes for out-of-specification stall speed are as fol-
lows. Check each part which is suspected to be the cause.
Stall speed measured
Possible causes
Lower than specification
Engine output insufficient

Torque converter defective
Higher than specification in
D range
Forward clutch slippage

One-way clutch defective
Higher than specification in
R range
Direct clutch slippage

1st-reverse brake slippage

1. Front drive shaft (LH)
2. Oil pan
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-33
LINE PRESSURE TEST
This test is to check oil pressure system for operation by measuring
oil pressure in oil pressure line. Make sure to perform this test only
when transmission fluid is at normal operating temperature.
NOTE:

Make sure that transmission fluid level is between FULL HOT
and LOW HOT marks on oil level gauge at normal operating
temperature which corresponds to 70–80C (155–176F) of
fluid. (Refer to “Fluid level” in this section.)

Check that transmission is free from fluid leakage.
1) With engine at stop, remove plug and connect oil pressure
gauge to plug hole.
Special Tool
(A): 09925-37811-001
2) Install tachometer.
3) Apply parking brake and block vehicle wheels.
4) With selector lever shifted to P range, start engine.
5) Depress brake pedal fully.
6) Shift selector lever to D range and check oil pressure with engine
running at idling speed and at stall speed respectively.
7) Repeat the same check as in step 6) with selector lever shifted
to R range.
CAUTION:
Do not run engine at stall more than 5 seconds continu-
ously, for oil temperature may rise excessively high.
8) If line pressure is within respective specification in table below,
oil pressure system is in good condition.
[G10 Engine Model]
Engine speedLine pressureEngine s eedD rangeR range
Idling speed
200 – 390 kPa
2.0 – 3.9 kg / cm2
28.4 – 55.5 psi
540 – 780 kPa
5.4 – 7.8 kg / cm2
76.8 – 110.9 psi
Stall speed
390 – 590 kPa
3.9 – 5.9 kg / cm2
55.5 – 83.9 psi
880 – 1230 kPa
8.8 – 12.3 kg / cm2
125.1 – 174.9 psi
[G13 Engine Model]
Engine speedLine pressureEngine s eedD rangeR range
Idling speed
260 – 460 kPa
2.6 – 4.6 kg / cm2
37.0 – 65.4 psi
660 – 900 kPa
6.6 – 9.0 kg / cm2
93.9 – 128.0 psi
Stall speed
660 – 850 kPa
6.6 – 8.5 kg / cm2
93.9 – 120.9 psi
1330 kPa or more
13.3 kg / cm2 or more
189.0 psi or more

NOTE:
Terminal arrangement of coupler viewed from harness side.
Coupler A
1. To generator W / R
2. To ignition switch B / W
3. To ECM V / G
4. To ECM V
5. Blank –
6. To ECT sensor Y / W
7. Blank —
8. To engine oil pressure switch Y / B
9. To ECM Br
10. Blank —
11. To SDM (if equipped) Bl
12. Blank —
13. Blank —
14. Blank —
15. To ground R
16. To combination switch R / Y
Coupler B
1. To combination switch G / R
2. Blank —
3. Blank —
4. To ECM Y / G
5. To brake fluid level switch and R / B
parking brake switch
6. Blank —
7. To ABS control module R / Bl
(if equipped)
8. Blank —
9. To fuel level gauge Y / R
10. To ground B / Bl
11. To ignition switch B / W
12. Blank —
13. Blank —
Coupler C
1. Blank —
2. Blank —
3. Blank —
4. Blank —
5. Blank —
6. Blank —
7. To main fuse R
8. To combination switch W / Bl
9. To ground B
10. To combination switch G / Y
Coupler A Coupler B Coupler C
8-2 BODY ELECTRICAL SYSTEM
GENERAL DESCRIPTION
COMBINATION METER