check oil SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

GENERAL INFORMATION 0A-5
CAUTION:

Even when the accident was light enough not to cause air
bags to deploy, be sure to inspect system parts and other
related parts according to instructions under “Repair and
Inspection Required after an Accident” in Section 9J.

When servicing parts other than air bag system, if shocks
may be applied to air bag system component parts, re-
move those parts beforehand.

When handling the air bag (inflator) modules (driver and
passenger) or SDM, be careful not to drop it or apply an im-
pact to it. If an excessive impact was applied (e.g.,
dropped from a height of 91.4 cm (3 feet) or more), never
attempt disassembly or repair but replace it with a new
one.

When grease, cleaning agent, oil, water, etc. has got onto
air bag (inflator) modules (driver and passenger), wipe off
immediately with a dry cloth.

Air bag wire harness can be identified easily as it is cov-
ered with a yellow protection tube. Be very careful when
handling it.

When an open in air bag wire harness, damaged wire har-
ness, connector or terminal is found, replace wire har-
ness, connectors and terminals as an assembly.

Do not apply power to the air bag system unless all com-
ponents are connected or a diagnostic chart requests it,
as this will set a diagnostic trouble code.

Never use air bag system component parts from another
vehicle.

When using electric welding, be sure to temporarily dis-
able air bag system referring to “Disabling Air Bag Sys-
tem” under “Service Precaution” in Section 9J.

Never expose air bag system component parts directly to
hot air (drying or baking the vehicle after painting) or
flames.

WARNING / CAUTION labels are attached on each part of
air bag system components. Be sure to follow the instruc-
tions.

After vehicle is completely repaired, perform “Air Bag
Diagnostic System Check” described in “Diagnosis” in
Section 9J.

0A-8 GENERAL INFORMATION

When disconnecting vacuum hoses, attach a tag describing
the correct installation positions so that the hoses can be re-
installed correctly.

After servicing fuel, oil, coolant, vacuum, exhaust or brake
systems, check all lines related to the system for leaks.

For vehicles equipped with fuel injection systems, never dis-
connect the fuel line between the fuel pump and injector
without first releasing the fuel pressure, or fuel can be
sprayed out under pressure.

When performing a work that produces a heat exceeding
80C in the vicinity of the electrical parts, remove the heat
sensitive electrical part(s) beforehand.

Use care not to expose connectors and electrical parts to wa-
ter which will be a cause of a trouble.

MAINTENANCE AND LUBRICATION 0B-7
Proper Engine Oil Viscosity Chart
1. Oil pan
2. Oil drain plug
1. Oil filter
ITEM 1-4
Engine Oil and Filter Change
WARNING:
New and used engine oil can be hazardous.
Be sure to read “WARNING” in General Precaution in SEC-
TION 0A and observe what in written there.
Use engine oil of SE, SF, SG, SH or SJ grade.
Select the appropriate oil viscosity according to the left chart.
Before draining engine oil, check engine for oil leakage. If any evi-
dence of leakage is found, make sure to correct defective part be-
fore proceeding to following work.
1) Drain engine oil by removing drain plug.
2) After draining oil, wipe drain plug clean. Reinstall drain plug, and
tighten it securely as specified below.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
3) Loosen oil filter by using oil filter wrench (Special tool).
Special Tool
(A): 09915-47330
4) Apply engine oil to new oil filter O-ring.
5) Screw new filter on oil filter stand by hand until filter O-ring con-
tacts mounting surface.
CAUTION:
To tighten oil filter properly, it is important to accurately
identify the position at which filter O-ring first contacts
mounting surface.
6) Tighten filter 3 / 4 turn from the point of contact with mounting sur-
face using an oil filter wrench.
Special Tool
(A): 09915-47330
Tightening Torque (Reference)
(a): 14 N
.m (1.4 kg-m, 10.5 lb-ft)

1. Full level mark (hole)
2. Low level mark (hole)
Oil pan capacity
Oil filter capacity
Others
Total1.0 L and 1.3 L Engine
About 3.1 liters
(6.5 / 5.5 US / lmp pt.)
About 0.2 liter
(0.4 / 0.3 US / lmp pt.)
About 0.3 liter
(0.6 / 0.5 US / lmp pt.)
About 3.6 liters
(7.5 / 6.3 US / lmp pt.)
0B-8 MAINTENANCE AND LUBRICATION
7) Replenish oil until oil level is brought to FULL level mark on dip-
stick (oil pan and oil filter capacity). Filler inlet is at the top of cyl-
inder head cover.
8) Start engine and run it for three minutes. Stop it and wait another
5 minutes before checking oil level. Add oil, as necessary, to
bring oil level to FULL level mark on dipstick.
Engine Oil Capacity
NOTE:
Engine oil capacity is specified as left table.
However, note that amount of oil required when actually
changing oil may somewhat differ from data in left table de-
pending on various conditions (temperature, viscosity, etc.).
9) Check oil filter and drain plug for oil leakage.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
CAUTION:
When changing engine coolant, use mixture of 50% water
and 50% ethylene-glycol base coolant (Anti-Freeze/Anti-
corrosion coolant) for the market where ambient tempera-
ture falls lower than –16C (3F) in winter and mixture of
70% water and 30% ethylene-glycol base coolant for the
market where ambient temperature doesn’t fall lower than
–16C (3F).
Even in a market where no freezing temperature is antici-
pated, mixture of 70% water and 30% ethylene-glycol base
coolant should be used for the purpose of corrosion protec-
tion and lubrication.
Refer to SECTION 6B for COOLANT CAPACITY.

1.0 liter engine
1.3 liter engine
MAINTENANCE AND LUBRICATION 0B-11
2) Visually check that air cleaner filter is not excessively dirty, dam-
aged or oily.
3) Clean filter with compressed air from air outlet side of filter.
4) Install air cleaner filter into case.
5) Clamp case cap securely and install hose to case and bracket
if removed.
Air Cleaner Filter Replacement
Replace air cleaner filter with new one according to steps 1), 4) and
5) of Air Cleaner Filter Inspection.
ITEM 3-2
Fuel Lines Inspection

Check fuel lines for loose connection, deterioration or damage
which could cause leakage.
Make sure all clamps are secure.

Replace any damaged or deteriorate parts.
There should be no sign of fuel leakage or moisture at any fuel
connection.
ITEM 3-3
Fuel Tank Inspection
Check fuel tank for damage, cracks, fuel leakage, corrosion and
tank bolts looseness.
If a problem is found, repair or replace.

1. Drive shaft
2. Boot
MAINTENANCE AND LUBRICATION 0B-15
[Wheel disc inspection]
Inspect each wheel disc for dents, distortion and cracks. A disc in
badly damaged condition must be replaced.
[Tire rotation]
Rotate tires referring to SECTION 3F.
Wheel Bearing Inspection
1) Check front wheel bearing for wear, damage, abnormal noise or
rattles. For details, refer to SECTION 3D.
2) Check rear wheel bearing for wear, damage abnormal noise or
rattle. For details, refer to SECTION 3E.
ITEM 6-3
Propeller Shaft Inspection (4WD vehicle only)
1) Check propeller shaft connecting bolts for looseness. If loose-
ness is found, tighten to specified torque.
2) Check propeller shaft joints for wear, play and damage.
If any defect is found, replace.
3) Check propeller shaft center support (1) for biting of foreign mat-
ter, crack, abnormal noise and damage. If any defect is found,
replace.
Drive Shaft Boot Inspction
Check drive shaft boots (wheel side and differential side) for leak-
age, detachment, tear or any other damage.
Replace boot as necessary.
ITEM 6-4
Suspension System Inspection

Inspect front & rear struts for evidence of oil leakage, dents or any
other damage on sleeves; and inspect anchor ends for deteriora-
tion.
Replace defective parts, if any.

2WD
4WD
1. Oil filler / level plug
2. Oil drain plug
MAINTENANCE AND LUBRICATION 0B-17
ITEM 6-7
Manual Transmission Oil Inspection and Change
[Inspection]
1) Inspect transmission case for evidence of oil leakage.
Repair leaky point if any.
2) Make sure that vehicle is placed level for oil level check.
3) Remove oil level plug of transmission.
4) Check oil level.
Oil level can be checked roughly by means of filler / level plug
hole. That is, if oil flows out of level plug hole or if oil level is found
up to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified oil up to level hole.
For specified oil, refer to description of oil change under ON-VE-
HICLE SERVICE in SECTION 7A or 7A1.
5) Tighten level plug to specified torque.
[Change]
1) Place the vehicle level and drain oil by removing drain plug.
2) Apply sealant to drain plug and tighten drain plug to specified
torque.
3) Pour specified oil up to level hole.
4) Tighten filler plug to specified torque.
For recommended oil, its amount and tightening torque data, re-
fer to ON-VEHICLE SERVICE of SECTION 7A or 7A1.
ITEM 6-8
Rear Differential Oil Inspection and Change
(4WD vehicle only)
[Inspection]
1) Inspect rear differential case for evidence of oil leakage.
Repair leaky point, if any.
2) Make sure that the vehicle is placed level for oil level check.
3) Remove level plug (1) of differential. Oil level can be checked
roughly by means of level plug hole.
That is, if oil flows out of level plug hole or if oil level is found up
to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified amount of specified oil
as given in SECTION 7E.
4) Tighten it to specified torque.
[Change]
Place the vehicle level and drain oil by removing drain plug (2). Pour
specified amount of specified oil, tighten drain plug and filler plug
to specified torque, referring to ON-VEHICLE SERVICE in SEC-
TION 7E.

1. Oil level gauge
2. FULL HOT mark
3. LOW HOT mark
4. FULL COLD mark
5. LOW COLD mark
1. Drain plug
0B-18 MAINTENANCE AND LUBRICATION
ITEM 6-9
Automatic Transmission
[Fluid level inspection]
1) Inspect transmission case for evidence of fluid leakage.
Repair leaky point, if any.
2) Make sure that vehicle is placed level for fluid level check.
3) Check fluid level.
For fluid level checking procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B and be sure to perform it under specified
conditions. If fluid level is low, replenish specified fluid.
[Fluid change]
1) Perform steps 1) and 2) of above Fluid Level Inspection.
2) Change fluid. For its procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B.
CAUTION:
Use of specified fluid is absolutely necessary.
[Fluid cooler hose change]
Replace inlet and outlet hoses (1) of cooler hose and their clamps.
For replacement procedure, refer to ON-VEHICLE SERVICE in
SECTION 7B.

“A”: Oil point
1. Upper hinge
2. Lower hinge
3. Door
4. Body
MAINTENANCE AND LUBRICATION 0B-19
ITEM 6-10
All Latches, Hinges and Locks Inspection
Doors
Check that each door of front, rear and back doors opens and
closes smoothly and locks securely when closed.
If any malfunction is found, lubricate hinge and latch or repair door
lock system.
Engine hood
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.). Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.

MAINTENANCE AND LUBRICATION 0B-21
[Parking brake]
Check that lever has proper travel.
Check to ensure that parking brake is fully effective
when the vehicle is stopped on the safe slope and
brake lever is pulled all the way.
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to “HI” position and mode lever to
defroster position for this check. WARNING:
With vehicle parked on a fairly steep slope,
make sure nothing is in the way downhill to
avoid any personal injury or property damage.
Be prepared to apply regular brake quickly
even if vehicle should start to move.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSE, SF, SG, SH or SJ (Refer to engine oil viscosity chart in item 1-4.)
Engine coolantEthylene-glycol base coolant (“Antifreeze / Anticorrosion coolant”)
Brake fluidDOT3
Manual transmission oilSee SECTION 7A
Rear differential oilSee SECTION 7E
Automatic transmission fluidAn equivalent of DEXRON-IIE or DEXRON-III
Power steering fluidSee material table on SECTION 3B1
Door hingesEngine oil
Engine hood latchEngine oil
Key lock cylinderSpray lubricant