sensor pressure SUZUKI SWIFT 2000 1.G SF310 Service Owner's Guide

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-25
ConditionPossible CauseReferring Item
Engine hesitates
(Momentary lack of
response as
accelerator is
depressed.
Can occur at all
vehicle speeds.
Usually most severe
when first trying to
make vehicle move,
as from a stop sign.)Ignition system out of order

Spark plug faulty or plug gap out of adjustment

Leaky high-tension cord
Fuel system out of order

Fuel pressure out of specification
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
Engine overheating
Low compression
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-3
EGR system in section 6E2
TP sensor, ECT sensor or MAP
sensor in Section 6E2
Diagnostic Flow Table B-1
Refer to “Overheating” section
Previously outlined
Surge
(Engine power
variation under
steady throttle or
cruise.
Feels like vehicle
speeds up and down
with no change in
accelerator pedal.)Ignition system out of order

Leaky or loosely connected high-tension cord

Faulty spark plug (excess carbon deposits,
improper gap, and burned electrodes, etc.)
Fuel system out of order

Variable fuel pressure
–Kinky or damaged fuel hose and lines
–Faulty fuel pump (clogged fuel filter)
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
High-tension cords in Section 6F1
Spark plugs in Section 6F1
Diagnostic Flow Table B-3
EGR system in Section 6E2
MAP sensor in Section 6E2
Diagnostic Flow Table B-1
Excessive
detonation
(Engine makes
continuously
sharp metallic
knocks that change
with throttle opening.
Sounds like pop corn
popping.)Engine overheating
Ignition system out of order

Faulty spark plug

Loose connection of high-tension cord
Fuel system out of order

Clogged fuel filter (faulty fuel pump) or fuel lines

Air inhaling from intake manifold or throttle body
gasket
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of ECT sensor or MAP sensor

Faulty fuel injector(s).

Faulty ECM (PCM)

Excessive combustion chamber depositsRefer to “Overheating” section
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-1 or B-2
EGR system in Section 6E2
ECT sensor or MAP sensor in
Section 6E2
Diagnostic Flow Table B-1
Piston and cylinder head cleaning
in Section 6A1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-27
ConditionPossible CauseReferring Item
Improper engine
idling or engine
fails to idleIgnition system out of order

Faulty spark plug

Leaky or disconnected high-tension cord

Faulty ignition coil with ignitor
Fuel system out of order

Fuel pressure out of specification

Leaky manifold, throttle body, or cylinder head
gasket
Engine and emission control system out of
order

Malfunctioning EGR valve

Faulty idle air control system

Faulty evaporative emission control system

Faulty EGR system

Faulty fuel injector(s)

Poor performance of ECT sensor, TP sensor or
MAP sensor

Faulty ECM (PCM)
Engine overheating
Low compression
Others

Loose connection or disconnection of vacuum
hoses

Malfunctioning PCV valve
Spark plugs in Section 6F
High-tension cords in Section 6F
Ignition coil in Section 6F
Diagnostic Flow Table B-3
EGR system in Section 6E2
Diagnostic Flow Table B-4
EVAP control system in Section
6E2
EGR system in Section 6E2
Diagnostic Flow Table B-1
ECT sensor, TP sensor or MAP
sensor in Section 6E2
Refer to “Overheating” section
Previously outlined
PCV system in Section 6E2

6-1-28 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ConditionPossible CauseReferring Item
Excessive
hydrocarbon (HC)
emission or carbon
monoxide (CO)Ignition system out of order

Faulty spark plug

Leaky or disconnected high-tension cord

Faulty ignition coil with ignitor
Low compression
Engine and emission control system out of
order

Lead contamination of three way catalytic
converter

Faulty evaporative emission control system

Fuel pressure out of specification

Closed loop system (A / F feed back
compensation) fails
–Faulty TP sensor
–Poor performance of ECT sensor or MAP
sensor

Faulty injector(s)

Faulty ECM (PCM)
Others

Engine not at normal operating temperature

Clogged air cleaner

Vacuum leaks
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Ignition coil assembly in Section
6F1
Refer to “Low compression”
section
Check for absence of filler neck
restrictor
EVAP control system in Section
6E2
Diagnostic Flow Table B-3
TP sensor in Section 6E2
ECT sensor or MAP sensor in
Section 6E2
Diagnostic Flow Table B-1
Excessive nitrogen
oxides (NOx)
emissionIgnition system out of order

Improper ignition timing
Engine and emission control system out of
order

Lead contamination of catalytic converter

Faulty EGR system

Fuel pressure out of specification

Closed loop system (A / F feed back
compensation) fails
–Faulty TP sensor
–Poor performance of ECT sensor or MAP
sensor

Faulty injector(s)

Faulty ECM (PCM)
See section 6F1
Check for absence of filler neck
restrictor.
EGR system in Section 6E2
Diagnostic Flow Table B-3
TP sensor in Section 6E2
ECT sensor or MAP sensor in
Section 6E2
Diagnostic Flow Table B-1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-29
SCAN TOOL DATA
As the data values given below are standard values estimated on the basis of values obtained from the normally
operating vehicles by using a scan tool, use them as reference values. Even when the vehicle is in good condition,
there may be cases where the checked value does not fall within each specified data range. Therefore, judgment
as abnormal should not be made by checking with these data alone.
Also, conditions in the below table that can be checked by the scan tool are those detected by ECM (PCM) and
output from ECM (PCM) as commands and there may be cases where the engine or actuator is not operating (in
the condition) as indicated by the scan tool. Be sure to use the timing light to check the ignition timing.
NOTE:

With the generic scan tool, only star () marked data in the table below can be read.

When checking the data with the engine running at idle or racing, be sure to shift M / T gear to the neutral
gear position and A / T gear to the “Park” position and pull the parking brake fully. Also, if nothing or “no
load” is indicated, turn OFF A / C, all electric loads, P / S and all the other necessary switches.
SCAN TOOL DATAVEHICLE CONDITIONNORMAL CONDITION /
REFERENCE VALUES
FUEL SYSTEM B1 (FUEL
SYSTEM STATUS)At specified idle speed after warming upCLOSED
(closed loop)

CALC LOAD
(CALCULATED LOADAt specified idle speed with no load after
warming up3 – 9%(
VALUE)At 2500 r / min with no load after warming up12 – 17%

COOLANT TEMP.
(ENGINE COOLANT
TEMP.)
At specified idle speed after warming up85 – 100C,
185 – 212F
SHORT FT BI (SHORT
TERM FUEL TRIM)At specified idle speed after warming up–20 – +20%
LONG FT BI (LONG
TERM FUEL TRIM)At specified idle speed after warming up–15 – +15%

MAP (INTAKE
MANIFOLD ABSOLUTE
PRESSURE)At specified idle speed with no load after
warming up24 – 37 kPa,
180 – 280 mmHg
ENGINE SPEEDAt idling with no load after warming up
Desired
idle speed
± 50 r / min
VEHICLE SPEEDAt stop0 km / h, 0 MPH

IGNITION ADVANCE
(IGNITION TIMING
ADVANCE FOR NO.1
CYLINDER)
At specified idle speed with no load after
warming up9 – 15 BTDC
INTAKE AIR TEMP.At specified idle speed after warming upAmbient +35C (95F)
temp.–5C (23F)
MAF (MASS AIR FLOW
RATE)
At specified idle speed with no load after
warming up0 – 4 gm / sec
RATE)At 2500 r / min with no load after warming up4 – 9 gm / sec

THROTTLE POS
(ABSOLUTE
Ignition switch
ON / engineThrottle valve fully closed7 – 18%
(ABSOLUTE
THROTTLE POSITION)
ON / engine
stoppedThrottle valve fully open70 – 100%
O2S B1 S1 (HEATED
OXYGEN SENSOR-1)At specified idle speed after warming up0.05 – 0.95 V
O2S B1 S2 (HEATED
OXYGEN SENSOR-2)When engine is running at 2000 r / min. for
3 min or longer after warming up.0 – 0.95 V
O2S FT B1 S1At specified idle speed after warning up–20 – +20%
DIS. WITH MIL ON————

6-1-30 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
SCAN TOOL DATACONDITIONNORMAL CONDITION /
REFERENCE VALUES
DESIRED IDLE
(DESIRED IDLE SPEED)At idling with no load after warming up, M / T
at neutral, A / T at “P” range750 r / min
TP SENSOR VOLT
(THROTTLE POSITIONIgnition switch
ON / engine
Throttle valve fully closedMore than 0.2 V(
SENSOR OUTPUT
VOLTAGE)ON / engine
stoppedThrottle valve fully openLess than 4.8 V
INJ PULSE WIDTH
(FUEL INJECTION
At specified idle speed with no load after
warming up2.0 – 3.6 msec.(
PULSE WIDTH)At 2500 r / min with no load after warming up2.0 – 3.6 msec.
IAC FLOW DUTY (IDLE
AIR CONTROL FLOW
DUTY)
At idling with no load after warming up5 – 25%
TOTAL FUEL TRIMAt specified idle speed after warming up–35 – +35%
BATTERY VOLTAGEIgnition switch ON / engine stop10 – 14 V
CANIST PRG DUTY
(EVAP CANISTER
PURGE FLOW DUTY)
––––––––––––0 – 100%
CLOSED THROT POS
(CLOSED THROTTLEThrottle valve at idle positionON(CLOSED THROTTLE
POSITION)Throttle valve opens larger than idle positionOFF
FUEL CUTWhen engine is at fuel cut conditionONFUEL CUTOther than fuel cut conditionOFF
RADIATOR FAN
(RADIATOR FANIgnition switch
ON
Engine coolant temp.:
Lower than 92.5C
Lower than (199F)
OFF
(
CONTROL RELAY)ONEngine coolant temp.:
97.5C (208F) or higherON
ELECTRIC LOAD
Ignition switch ON / Headlight, small light,
heater fan and rear window defogger all
turned OFF
OFF
ELECTRIC LOADIgnition switch ON / Headlight, small light,
heater fan or rear window defogger turned
ON
ON
A / C SWITCH
Engine running after warming up, A / C not
operatingOFF
A/C SWITCHEngine running after warming up, A / C
operatingON
PNP SIGNAL (PARK /
NEUTRAL POSITIONIgnition switch
Selector lever in “P” or “N”
positionP / N Range
NEUTRAL POSITION
SIGNAL) A / T only
g
ONSelector lever in “R”, “D”, “2”
or “L” positionD Range
EGR VALVEAt specified idle speed after warming up0%
FUEL TANK LEVEL––––––––––––0 – 100%
BAROMETRIC PRESS––––––––––––Display the barometric pressure
FUEL PUMP
Within 3 seconds after ignition switch ON or
engine runningON
Engine stop at ignition switch ON.OFF
BRAKE SWIgnition switchBrake pedal is depressingONBRAKE SWg
ONBrake pedal is releasingOFF
BLOWER FANIgnition switchBlower fan switch ONONBLOWER FA Ng
ONBlower fan switch OFFOFF
A / C MAG CLUTCHIgnition switchA / C switch ONONA/C MAG CLUTCHg
ONA / C switch OFFOFF

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-31
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates current flow time rate within
a certain set cycle of IAC valve (valve opening rate)
which controls the amount of bypass air (idle speed).
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

6-1-34 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
CONNECTOR “C01”
TERMINAL
NO.CIRCUITNORMAL
VOLTAGECONDITION
1Ground——
2Ground——
3Ground——
4EVAP canister purge valve10 – 14 VIgnition switch ON
Indication
deflection
5Power steering switch
deflection
repeated
0 V and
Ignition switch ON
0 V and
10 – 14 V
6Idle air control valve0 – 13 VAt specified idle speed after engine warmed
up
7Heater of HO2S-110 – 14 VIgnition switch ON
8Fuel injector NO.410 – 14 VIgnition switch ON
9Fuel injector NO.110 – 14 VIgnition switch ON
10Sensor ground——
11Camshaft position sensor0 – 0.8 V
and 4 – 6 VIgnition switch ON
12Blank——
13Heater oxygen sensor-1Refer to DTC P0130 diag. flow table
14Engine coolant temp. sensor0.55 – 0.95 VIgnition switch ON
Engine coolant temp.: 80C (176F)
15Intake air temp. sensor2.0 – 2.7 VIgnition switch ON
Intake air temp.: 20C (68F)
16Blank——
17Electric load signal (+)
0 – 1 VIgnition switch ON
Small light and rear defogger OFF
17Electric load signal (+)
10 – 14 VIgnition switch ON
Small light and rear defogger ON
18Blank——
19Ignition coil #2——
20Ignition coil #1——
21Fuel injector NO.210 – 14 VIgnition switch ON
22Power source for sensor4.75 – 5.25 VIgnition switch ON
23Crankshaft position sensor (+)——
24Crankshaft position sensor (–)——
25Blank——
26Manifold absolute pressure
sensor3.3 – 4.0 VIgnition switch ON
Barometric pressure: 100 kPa (760 mmHg)
27Blank——
28Immobilizer indicator lamp0 – 2 VIgnition switch ON28Immobilizer indicator lamp10 – 14 VWhen engine running
29Blank——
30Blank——
31Fuel injector NO.310 – 14 VIgnition switch ON

MAP
sensor
To other sensorsTo TP sensor
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-43
DTC P0105 MANIFOLD ABSOLUTE PRESSURE (MAP) CIRCUIT
MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

MAP: 4.9 kpa, 37 mmHg or less
(Low pressure – High vacuums – Low voltage)

MAP: 114.7 kpa, 860 mmHg or more
(High pressure – Low vacuums – High voltage)
“G” circuit open

“P” circuit open or shorted to ground

“G” circuit open or shorted to ground

MAP sensor malfunction

ECM (PCM) malfunction
NOTE:
When DTC P0120 is indicated together, it is possible that “P” circuit is open.
DTC CONFIRMATION PROCEDURE
1) Clear DTC, start engine and keep it at idle for 1 min.
2) Select “DTC” mode on scan tool and check DTC.

6-1-44 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
MAP Sensor Individual Check
1) Disconnect coupler from MAP sensor (1).
2) Remove MAP sensor (1).
3) Arrange 3 new 1.5 V batteries (2) in series (check that total volt-
age is 4.5 – 5.0 V) and connect its positive terminal to “Vin” termi-
nal of sensor and negative terminal to “Ground” terminal. Then
check voltage between “Vout” and “Ground”.
Also, check if voltage reduces when vacuum is applied up to 400
mmHg by using vacuum pump (3).
Output voltage (Vin voltage 4.5 – 5.5 V, ambient temp. 20 –
30C, 68 – 86F)
ALTITUDE
BAROMETRICOUTPUT
(Reference)PRESSUREVOLTAGE
(ft)(m)(mmHg)(kPa)(V)
0


0


760


100

3343

2 000


610


707


94
3.3 – 4.3
2 001


611

Under 70794

3041

5 000


1 524over 634

85
3.0 – 4.1
5 001


1 525

Under 63485

2737

8 000


2 438over 567

76
2.7 – 3.7
8 001


2 439

Under 56776

25–33

10 000


3 048over 526

70
2.5 – 3.3
If check result is not satisfactory, replace MAP sensor (1).
4) Install MAP sensor (1) securely.
5) Connect MAP sensor (1) coupler securely.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-45
Fig. 1 for Step 2 Fig. 2 for Step 3
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE”
performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check MAP Sensor and Its Circuit.
1) Connect scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON.
3) Check intake manifold pressure.
See Fig. 1.
Is it 114.7 kPa or more or 4.9 kPa or less?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to
“INTERMITTENT AND
POOR CONNECTION” in
Section 0A.
3Check Wire Harness.
1) Disconnect MAP sensor connector with
ignition switch OFF.
2) Check for proper connection of MAP
sensor at “Gr” and “G” wire terminals.
3) If OK, then with ignition switch ON, check
voltage at each of “P” and “Gr” wire
terminals. See Fig. 2.
Is voltage about 4 – 6 V at each terminal?Go to Step 4.“P” wire open or shorted to
ground circuit or shorted to
power circuit, “Gr” wire
open or shorted to ground,
poor C03-5 connection or
C01-22 connection.
If wire and connection are
OK, confirm that MAP
sensor is normal and then
substitute a known-good
ECM (PCM) and recheck.
NOTE: When battery
voltage is applied to
“P” wire, it is possible
that MAP sensor is also
faulty.
4Check MAP sensor according to “MAP
Sensor Individual Check” below.
Is it in good condition?“P” wire shorted to “Gr”
wire, “G” wire open,
poor C01-10 connection.
If wire and connection are
OK, substitute a known-
good ECM (PCM) and
recheck.Replace MAP sensor.