Adjust SUZUKI SWIFT 2000 1.G SF310 Service Repair Manual

6E1-34 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
1. Tank pipe
2. Purge pipe
3. Air pipe
4. Blow air
1. Tank pressure
control valve
2. Orange side3. Black side
4. To canister
5. From fuel tank
EVAP CANISTER INSPECTION
WARNING:
DO NOT SUCK nozzles on EVAP canister. Fuel vapor inside
EVAP canister is harmful.
1) Disconnect vacuum hoses from EVAP canister and remove
EVAP canister.
2) When air is blown into tank pipe, there should be no restriction
of flow through purge pipe and air pipe.
If operation differs from above description, EVAP canister must
be replaced.
3) Install EVAP canister and connect hoses to canister.
TANK PRESSURE CONTROL VALVE INSPECTION
WARNING:
DO NOT SUCK air through tank pressure control valve.
Fuel vapor inside the valve is harmful.
1) Remove tank pressure control valve.
2) Air should pass through valve smoothly from fuel tank side
(black side of tank pressure control valve) to orange side when
blown hard.
3) From orange side, even when blown softly, air should come out
of black side.
4) If air doesn’t pass though valve in step 2) or hard blow is required
in step 3), replace tank pressure control valve.
5) Install tank pressure control valve.
NOTE:
When connecting tank pressure control valve between
hoses, refer to figure at the left for installing direction.
PCV SYSTEM
NOTE:
Be sure to check that there is no obstruction in PCV valve or
its hoses before adjusting engine idle speed, for obstructed
PCV valve or hose hampers its accurate adjustment.
PCV HOSE INSPECTION
Check hoses for connection, leakage, clog and deterioration.
Replace as necessary.

6E2
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-1
GENERAL DESCRIPTION6E2- 2 . . . . . . . . . . . . . .
AIR INTAKE SYSTEM 6E2- 6. . . . . . . . . . . . . . . . . .
FUEL DELIVERY SYSTEM 6E2- 7. . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E2- 8. . . . . .
Engine and Emission Control Input /
Output Table 6E2- 9. . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSISSee Section 6. . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE6E2-13 . . . . . . . . . . . . . . . .
Accelerator Cable Adjustment 6E2-13. . . . . . . . . .
Idle Speed/Idle Air Control (IAC)
Duty Inspection 6E2-14. . . . . . . . . . . . . . . . . . . . .
AIR INTAKE SYSTEM 6E2-15. . . . . . . . . . . . . . . . . .
Throttle Body 6E2-15. . . . . . . . . . . . . . . . . . . . . . . .
Idle Air Control Valve 6E2-17. . . . . . . . . . . . . . . . .
FUEL DELIVERY SYSTEM 6E2-18. . . . . . . . . . . . . .
Fuel Pressure Inspection 6E2-18. . . . . . . . . . . . . .
Fuel Pump 6E2-21. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pressure Regulator 6E2-22. . . . . . . . . . . . . . .
Fuel Injector 6E2-23. . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E2-27. . . . . .
ECM / PCM 6E2-27. . . . . . . . . . . . . . . . . . . . . . . . . .
MAP Sensor 6E2-27. . . . . . . . . . . . . . . . . . . . . . . . .
TP Sensor 6E2-28. . . . . . . . . . . . . . . . . . . . . . . . . . .
IAT Sensor 6E2-29. . . . . . . . . . . . . . . . . . . . . . . . . .
ECT Sensor 6E2-30. . . . . . . . . . . . . . . . . . . . . . . . . Heated Oxygen Sensor -1 and -2 6E2-31. . . . . . .
Camshaft Position Sensor 6E2-32. . . . . . . . . . . . .
Crankshaft Position Sensor 6E2-32. . . . . . . . . . . .
Vehicle Speed Sensor 6E2-33. . . . . . . . . . . . . . . . .
Fuel Level Sensor (gauge) 6E2-33. . . . . . . . . . . . .
Main Relay, Fuel Pump Relay and
Radiator Fan Control Relay 6E2-33. . . . . . . . . . .
Fuel Cut Operation (Inspection) 6E2-34. . . . . . . .
Radiator Fan Control System 6E2-34. . . . . . . . . .
System Inspection 6E2-34. . . . . . . . . . . . . . . . . .
Radiator Fan 6E2-34. . . . . . . . . . . . . . . . . . . . . . .
EMISSION CONTROL SYSTEM 6E2-35. . . . . . . . .
EGR System 6E2-35. . . . . . . . . . . . . . . . . . . . . . . . .
EVAP Control System 6E2-36. . . . . . . . . . . . . . . . .
EVAP Canister Purge Inspection 6E2-36. . . . . .
Vacuum Passage Inspection 6E2-37. . . . . . . . .
Vacuum Hose Inspection 6E2-37. . . . . . . . . . . .
EVAP Canister Purge Valve
Inspection 6E2-37. . . . . . . . . . . . . . . . . . . . . . . .
EVAP Canister Inspection 6E2-38. . . . . . . . . . .
PCV System 6E2-38. . . . . . . . . . . . . . . . . . . . . . . . .
PCV Hose Inspection 6E2-38. . . . . . . . . . . . . . .
PCV Valve Inspection 6E2-38. . . . . . . . . . . . . . .
SPECIAL TOOLS6E2-39 . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS6E2-39 . . . . . . . . . . . . . . . . . . . . .
SECTION 6E2
ENGINE AND EMISSION CONTROL SYSTEM
(SFI FOR G13)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

1. Accelerator cable
3. Lock nut
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-13
ON-VEHICLE SERVICE
ACCELERATOR CABLE ADJUSTMENT
1) With throttle valve closed, check accelerator pedal play which
should be within following specification.
Pedal play “a”: 2 – 7 mm (0.08 – 0.27 in.)
If measured value is out of specification, adjust it to specification
with cable adjusting nut (2).
2) With accelerator pedal depressed fully (1), check clearance be-
tween throttle lever (2) and lever stopper (3) (throttle body)
which should be within following specification.
Clearance “b” : 0.5 – 2.0 mm (0.02 – 0.07 in.)
(With pedal
depressed fully)
If measured value is out of specification, adjust it to specification
with cable adjusting nut.

6E2-14 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
IDLE SPEED / IDLE AIR CONTROL (IAC) DUTY
INSPECTION
Before idle speed / IAC duty check, make sure of the following.

Lead wires and hoses of Electronic Fuel Injection and engine
emission control systems are connected securely.

Accelerator cable has some play, that is, it is not tight.

Valve lash is checked and adjusted according to maintenance
schedule.

Ignition timing is within specification.

All accessories (wipers, heater, lights, A / C, etc.) are out of ser-
vice.

Air cleaner has been properly installed and is in good condition.

No abnormal air inhaling from air intake system.
After above items are all confirmed, check idle speed and IAC duty
as follows.
NOTE:
Before starting engine, place transmission gear shift lever in
“Neutral” (shift selector lever to “P” range for A / T vehicle),
and set parking brake and block drive wheels.
1) Connect SUZUKI scan tool (1) to DLC with ignition switch OFF,
if it is available.
2) Warm up engine to normal operating temperature.
3) Check engine idle speed and “IAC duty” as follow:
Select “Data List” mode on scan tool to check “IAC duty” and en-
gine speed.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
If duty and/or idle speed is out of specifications, inspect idle air
control system referring to Diagnostic Flow Table B-4 IDLE AIR
CONTROL SYSTEM CHECK in Section 6.
ENGINE IDLE SPEED AND IAC DUTY
A/C OFFA/C ON
M / T vehicle750±50 r / min (rpm)875±50 r/minA / T vehicle
at P/N range750 ±50 r/min (rpm)
8 – 25 or *8 – 35%
875 ±50 r/min
(rpm)
NOTE:
Duty values with (*) are applicable to vehicle used at high
altitude (higher than 2,000 m or 6,560 ft).
4) Check that 875 ± 50 r / min. idle speed is obtained with lighting
switch ON and heater blower switch in 2 – 4 position.
If not, check “Electric load (+)” circuit and “Heater blower switch
signal” circuit referring to “ELECTRONIC CONTROL SYSTEM”
in this section and idle air control system.
5) Check that specified engine idle speed is obtained with A / C ON
if vehicle is equipped with A / C.
If not, check A / C ON signal circuit.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-15
CAUTION:
Do not disassemble IAC
valve. Disassembly spoils
its original performanceCAUTION:
Do not remove or adjust
throttle stop screw as it is
factory adjusted precisely
1. Throttle body
2. Throttle stop screw
3. TP sensor
4. O-ring
5. Idle air control valve
6. IAC valve screws : Tightening torque
: Do not reuse
AIR INTAKE SYSTEM
THROTTLE BODY
On-Vehicle Inspection

Check that throttle valve lever (1) moves smoothly.
Removal
1) Disconnect negative cable at battery.
2) Drain cooling system.
3) Disconnect accelerator cable (1) from throttle body.
4) Disconnect air cleaner outlet hose (1) from throttle body.

21
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-17
2) Connect engine coolant hoses (1).
3) Install throttle body (4) to intake manifold.
4) Connect coupler to TP sensor (2) and IAC valve (3) securely.
5) Install air cleaner outlet hose (1) and pipe.
6) Connect accelerator cable and adjust cable play to specifica-
tion.
7) Refill cooling system.
8) Connect negative cable at battery.
IDLE AIR CONTROL VALVE (IAC VALVE)
Removal
1) Remove throttle body from intake manifold referring to “Throttle
Body Removal” section.
2) Remove IAC valve from throttle body.
Inspection
1) Connect each connector to IAC valve (1), TP sensor and IAT
sensor.
2) Check that rotary valve (2) of lAC valve opens and closes once
and then stops in about 60 ms as soon as ignition switch is
turned ON.
NOTE:

This check should be performed by two people, one per-
son turns on ignition switch while the other checks valve
operation.

As valve operation is momentary, it may be overlooked.
To prevent this, perform this operation check 3 times or
more continuously.
If rotary valve of lAC valve does not operate at all, check
wire harness for open and short. If wire harness is in good
condition, replace lAC valve and recheck.

6E2-38 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
EVAP Canister Inspection
WARNING:
DO NOT SUCK nozzles on EVAP canister. Fuel vapor inside
EVAP canister is harmful.
1) Check outside of EVAP canister visually.
2) Disconnect vacuum hoses from EVAP canister.
3) Check that there should be no restriction of flow through purge
pipe (2) and air pipe (3) when air is blown (4) into tank pipe (1).
If any faulty condition is found in above inspection replace.
PCV SYSTEM
NOTE:
Be sure to check that there is no obstruction in PCV valve or
its hoses before checking IAC duty, for obstructed PCV valve
or hose hampers its accurate adjustment.
PCV Hose Inspection
Check hoses for connection, leakage, clog and deterioration.
Replace as necessary.
PCV Valve Inspection
1) Disconnect PCV valve (1) from cylinder head cover and install
plug to head cover hole.
2) Run engine at idle.
3) Place your finger over end of PCV valve (1) to check for vacuum.
If there is no vacuum, check for clogged valve. Replace as nec-
essary.
4) After checking vacuum, stop engine and remove PCV valve (1).
Shake valve and listen for the rattle of check needle inside the
valve. If valve does not the rattle, replace valve.
5) After checking, remove plug and install PCV valve (1).

IGNITION SYSTEM 6F-3
DIAGNOSIS
ConditionPossible CauseCorrection
Engine cranks, but will
not start or hard to start
Blown fuse for ignition coil

Loose connection or disconnection of lead wire or
high-tension cord(s)

Faulty high-tension cord(s)

Faulty spark plug(s)

Cracked rotor or cap

Maladjusted signal rotor air gap

Faulty ignition coil

Faulty noise suppressor

Faulty CMP sensor

Faulty igniter

Faulty ECM (or PCM)

Maladjusted ignition timingReplace
Connect securely
Replace
Adjust, clean or replace
Replace
Adjust
Replace
Replace
Replace
Replace
Replace
Adjust
Poor fuel economy or
engine performance
Incorrect ignition timing

Faulty spark plug(s) or high-tension cord(s)

Faulty ECM (or PCM)Adjust
Adjust, clean or replace
Replace
DIAGNOSTIC FLOW TABLE
STEPACTIONYESNO
1Was “Engine Diagnostic Flow Table” in SECTION 6
performed?Go to Step 2.Go to “Engine
Diagnostic Flow
Table” in SECTION 6.
2Ignition Spark Test
1) Check all spark plug for condition and type,
referring to “Spark Plugs” in this section.
2) If OK, perform ignition spark test, referring to
“Ignition Spark Check” in this section.
Is spark emitted from all spark plugs?Go to Step 11 on the
next page.Go to Step 3.
3Diagnostic Trouble Code (DTC) Check
1) Check DTC stored in ECM (or PCM), referring to
“Diagnostic Trouble Code (DTC) Check” in
SECTION 6.
Is DTC stored?Go to applicable flow
table corresponding to
that code No. in
SECTION 6.Go to Step 4.
4Electrical Connection and Noise Suppressor Check
1) Check ignition coil for electrical connection and
noise suppressor for conductivity.
Are they good condition?Go to Step 5.Repair or replace.
5High-tension Cord Check
1) Check high-tension cord for resistance, referring
to “High-tension Cords” in this section.
Is check result satisfactory?Go to Step 6.Replace high-tension
cord(s).

6F-4 IGNITION SYSTEM
STEPACTIONYESNO
6Ignition Coil Power Supply and Ground Circuit
Check
1) Check ignition coil power supply (“B/W” wire)
circuit for open and short.
Are circuits in good condition?Go to Step 7.Repair or replace.
7Ignition Coil Check
1) Check ignition coil for resistance, referring to
“Ignition Coil” in this section.
Is check result satisfactory?Go to Step 8.Replace ignition coil
assembly.
8CMP Sensor Check
1) Check CMP sensor and signal rotor, referring to
“Distributor Unit” in this section.
Is check result satisfactory?Go to Step 9 on the
next page.Adjust or replace.
9Ignition Trigger Signal Circuit Check
1) Check ignition trigger signal (“Br / Y” or “Or” wire)
circuit for open, short and poor connection.
Are circuits in good condition?Go to Step 10.Repair or replace.
10Igniter Check
1) Check igniter, referring to “Igniter” in this section.
Is check result satisfactory?Go to Step 11.Replace igniter.
11Ignition Timing Check
1) Check initial ignition timing and ignition timing
advance, referring to “Ignition Timing” in this
section.
Is check result satisfactory?Substitute a known-
good ECM (or PCM)
and then repeat
Step 2.Go to Step 12.
12Ignition Timing Adjustment and Recheck
1) Adjust initial ignition timing, referring to “Ignition
Timing” in this section.
2) Recheck initial ignition timing and ignition timing
advance, referring to “Ignition Timing” in this
section.
Is check result satisfactory?System is in good
condition.Substitute a known-
good ECM (or PCM)
and then repeat
Step 2.

6F-6 IGNITION SYSTEM
6) If resistance exceeds specification, inspect distributor terminal
and replace high-tension cord(s) and/or distributor cap as re-
quired.
CAUTION:

Never attempt to use metal conductor high-tension cords
as replacing parts.

Insert each cap portion fully when installing high-tension
cords.
SPARK PLUGS
1) Pull out high-tension cords by gripping their caps and then re-
move spark plugs.
2) Inspect them for:

Electrode wear

Carbon deposits

Insulator damage
3) If any abnormality is found, adjust air gap, clean with spark plug
cleaner or replace them with specified new plugs.
Spark plug air gap “a’’: 1.0 – 1.1 mm (0.039 – 0.043 in.)
Spark plug type : NGK BPR6ES-11
: DENSO W20EPR-U11
4) Install spark plugs and torque them to specification.
Tightening Torque for spark plug
25 N
.m (2.5 kg-m, 18.0 lb-ft)
5) Install high-tension cords securely by gripping their caps.
NOISE SUPPRESSOR
REMOVAL
1) Unwrap tape from noise suppressor.
2) Disconnect coupler of noise suppressor.
3) Remove noise suppressor.
INSTALLATION
Reverse removal procedure for installation.
INSPECTION
Using an ohmmeter (1) to check continuity as the following.
“a” – “b”: No continuity
“a” – “c”: No continuity
“c” – “d”: Continuity (Approx. 2.2 kΩ)
If check result is not satisfactory, replace noise suppressor (2).