torque SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

GENERAL INFORMATION 0A-1
0ASECTION 0A
GENERAL INFORMATION
CONTENTS
HOW TO USE THIS MANUAL0A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS0A- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution for Vehicles Equipped with a Supplemental Restraint (Air Bag) System 0A- 3. . . . . . . . . . . . . . . .
General Precautions0A- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Catalytic Converter 0A- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Electrical Circuit Service 0A- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Circuit Inspection Procedure 0A-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intermittent and Poor Connection 0A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution for Installing Mobile Communication Equipment 0A-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution in Servicing Full-Time 4WD Vehicle 0A-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDENTIFICATION INFORMATION0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle Identification Number0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identification Whether Vehicle Equipped with WU-TWC or Not 0A-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Identification Number0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Identification Number 0A-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING, CAUTION AND INFORMATION LABELS0A-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE LIFTING POINTS0A-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABBREVIATIONS AND SYMBOLS MAY BE USED IN THIS MANUAL0A-22 . . . . . . . . . . . . . . . . . . . . . . . . . . .
FASTENER INFORMATION0A-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metric Fasteners0A-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fasteners Strength Identification 0A-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Tightening Torque0A-26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. Flywheel bolts or drive plate bolts for A / T vehicle
6) Install oil pump. Refer to “Oil pump”.
7) Install flywheel (for M / T vehicle) or drive plate
(for A / T vehicle).
Using special tool, lock flywheel or drive plate, and
tighten flywheel or drive plate bolts to specified
torque.
Special Tool
(A): 09924-17810
Tightening Torque
(c): 78 N
.m (7.8 kg-m, 56.0 lb-ft)
0A-2 GENERAL INFORMATION
HOW TO USE THIS MANUAL
1) There is a TABLE OF CONTENTS FOR THE WHOLE MANUAL
on the third page of this manual, whereby you can easily find the
section that offers the information you need. Also, there is a
CONTENTS on the first page of EACH SECTION, where the
main items in that section are listed.
2) Each section of this manual has its own pagination. It is indicated
at the top of each page along with the Section name.
3) The SPECIAL TOOL usage and TIGHTENING TORQUE
SPECIFICATION are given as shown in figure below.
4) A number of abbreviations are used in the text.
For their full explanations, refer to “ABBREVIATIONS AND
SYMBOLS MAY BE USED IN THIS MANUAL” of this section.
5) The SI, metric and foot-pound systems are used as units in this
manual.
6) DIAGNOSIS are included in each section as necessary.
7) At the end of each section, there are descriptions of SPECIAL
TOOLS, REQUIRED SERVICE MATERIALS and TIGHT-
ENING TORQUE SPECIFICATIONS that should be used for the
servicing work described in that section.

1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket
ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.
ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.
0A-4 GENERAL INFORMATION
HANDLING AND SERVICING
WARNING:

Many of service procedures require disconnection of
“AIR BAG” fuse and air bag (inflator) modules (driver and
passenger) from deployment loop to avoid an accidental
deployment.
Driver and Passenger Air Bag (Inflator) Modules

For handling and storage of a live air bag (inflator) module,
select a place where the ambient temperature below 65C
(150F), without high humidity and away from electric
noise.

When carrying a live air bag (inflator) module, make sure
the bag opening is pointed away from you. In case of an
accidental deployment, the bag will then deploy with mini-
mal chance of injury. Never carry the air bag (inflator)
module by the wires or connector on the underside of the
module. When placing a live air bag (inflator) module on
a bench or other surface, always face the bag up, away
from the surface. As the live passenger air bag (inflator)
module must be placed with its bag (trim cover) facing up,
place it on the workbench with a slit or use the workbench
vise to hold it securely at its lower mounting bracket. This
is necessary so that a free space is provided to allow the
air bag to expand in the unlikely event of accidental de-
ployment. Otherwise, personal injury may result.

Never dispose of live (undeployed) air bag (inflator) mod-
ules (driver and passenger). If disposal is necessary, be
sure to deploy them according to deployment procedures
described in Section 9J before disposal.

The air bag (inflator) module immediately after deploy-
ment is very hot. Wait for at least half an hour to cool it off
before proceeding the work.

After an air bag (inflator) module has been deployed, the
surface of the air bag may contain a powdery residue.
This powder consists primarily of cornstarch (used to lu-
bricate the bag as it inflates) and by-products of the chem-
ical reaction. As with many service procedures, gloves
and safety glasses should be worn.
SDM

During service procedures, be very careful when handling
a Sensing and Diagnostic Module (SDM). Never strike or
jar the SDM. Never power up the air bag system when the
SDM is not rigidly attached to the vehicle. All SDM and
mounting bracket fasteners must be carefully torqued
and the arrow must be pointing toward the front of the ve-
hicle to ensure proper operation of the air bag system. The
SDM could be activated when powered while not rigidly at-
tached to the vehicle which could cause deployment and
result in personal injury.

1. Transfer lock bolt
2. Shift fork shaft Testing following items

Speedometer

Chassis dynamo

Brake

Wheel balance (on car type)Towing vehicle with
front or rear
wheels lifted upDriving front
wheels which are
jacked up
4WD
2WD
GENERAL INFORMATION 0A-17
PRECAUTION IN SERVICING FULL-TIME 4WD VEHICLE
When performing any of the following types of work, be sure to make the vehicle as front wheel drive by cutting
transmission of driving force to the rear wheels. Otherwise, rear wheels are driven and vehicle accidents, damage
and personal injury may result.
SWITCHING FROM 4WD TO 2WD
Set 4WD / 2WD select lever located at lower side of transfer driven
case to 2WD as follows.
1) Loosen transfer lock bolt.
2) Push in shift fork shaft fully.
3) With shift fork shaft pushed in, tighten transfer lock bolt.
Tightening Torque
(a): 19 N
.m (1.9 kg-m, 14.0 lb-ft)
NOTE:

If shift fork shaft is hard to move, try to move it while turning
it to the right and left little by little. Do the same when setting
back to 4WD after servicing vehicle.

Upon completion of servicing, always set shift fork shaft
back to 4WD.

GENERAL INFORMATION 0A-23
L
LH : Left Hand
LSPV : Load Sensing Proportioning
Valve
M
MAF Sensor : Mass Air Flow Sensor (Air Flow
Sensor, AFS, Air Flow Meter,
AFM)
MAP Sensor : Manifold Absolute Pressure
Sensor (Pressure Sensor, PS)
Max : Maximum
MFI : Multiport Fuel Injection
(Multipoint Fuel Injection)
Min : Minimum
MIL : Malfunction Indicator Lamp
M / T : Manual Transmission
N
NOx : Nitrogen Oxides
O
OBD : On-Board Diagnostic System
(Self-Diagnosis Function)
O / D : Overdrive
OHC : Over Head Camshaft
P
PNP : Park / Neutral Position
P / S : Power Steering
PSP Switch : Power Steering Pressure Switch
(P / S Pressure Switch)
PCM : Powertrain Control Module
PCV : Positive Crankcase Ventilation
R
RH : Right Hand
S
SAE : Society of Automotive
Engineers
SDM : Sensing and Diagnostic Module
(Air Bag Controller, Air Bag
Control Module)
SFI : Sequential Multiport Fuel
Injection
SOHC : Single Over Head Camshaft
T
TBI : Throttle Body Fuel Injection
(Single-Point Fuel Injection,
SPI)
TCC : Torque Converter Clutch
TCM : Transmission Control Module
(A / T Controller, A / T Control
Module)
TP Sensor : Throttle Position Sensor
TVV : Thermal Vacuum Valve
(Thermal Vacuum Switching
Valve, TVSV, Bimetal Vacuum
Switching Valve, BVSV)
TWC : Three-Way Catalytic Converter
(Three-Way Catalyst)
2WD : 2 Wheel Drive
V
VIN : Vehicle Identification Number
VSS : Vehicle Speed Sensor
W
WU-OC : Warm Up Oxidation Catalytic
Converter
WU-TWC : Warm Up Three-Way Catalytic
Converter

G (Base Color)
G (Base Color)
Y (Stripe Color)
0A-24 GENERAL INFORMATION
SYMBOLS
SYMBOLDEFINITIONSYMBOLDEFINITION
Tightening torqueApply SUZUKI BOND NO. 1216
99000-31160
Apply oil (Engine, transmission,
transfer, differential)Apply SILICONE SEALANT
99000-31120
Apply fluid (Brake, power steering or
automatic transmission fluid)Apply SEALING COMPOUND 366E
99000-31090
Apply SUZUKI SUPER GREASE A
99000-25010
Apply SUZUKI SUPER GREASE C
99000-25030Apply THREAD LOCK 1322
99000-32110
Apply SUZUKI SUPER GREASE E
99000-25050Apply THREAD LOCK 1333B
99000-32020
Apply SUZUKI SUPER GREASE H
99000-25120Apply THREAD LOCK 1342
99000-32050
Apply SUZUKI SUPER GREASE I
99000-25210
Apply SUZUKI BOND NO. 1215
99000-31110Do not reuse
Apply SUZUKI BOND NO. 1207C
99000-31150Note on reassembly
WIRE COLOR SYMBOLS
SymbolWire ColorSymbolWire Color
BBLKBlackO, OrORNOrange
BlBLUBlueRREDRed
BrBRNBrownWWHTWhite
GGRNGreenYYELYellow
GrGRYGrayPPNKPink
LblLT BLULight blueVPPLViolet
LgLT GRNLight green
There are two kinds of colored wire used in this vehicle. One is
single-colored wire and the other is dual-colored (striped) wire.
The single-colored wire uses only one color symbol (i.e. “G”).
The dual-colored wire uses two color symbols (i.e. “G/Y”). The first
symbol represents the base color of the wire (“G” in the figure) and
the second symbol represents the color of the stripe (“Y” in the fig-
ure).

0A-26 GENERAL INFORMATION
Self-lock
nut
STANDARD TIGHTENING TORQUE
Each fastener should be tightened to the torque specified in each section of this manual. If no description or specifi-
cation is provided, refer to the following tightening torque chart for the applicable torque for each fastener. When
a fastener of greater strength than the original one is used, however, use the torque specified for the original fasten-
er.
NOTE:

For the flanged bolt, flanged nut and self-lock nut of 4T and 7T strength, add 10% to the tightening torque
given in the chart below.

The chart below is applicable only where the fastened parts are made of steel or light alloy.
Tightening torque chart
Thread Diameter (Nominal Diameter)
(mm)
45681012141618
Strength
A equivalent of 4T strength
fastenerN.m1.53.05.513294565105160
kg-m0.150.300.551.32.94.56.510.516
lb-ft1.02.54.09.521.032.547.076.0116.0
A equivalent of 6.8 strength
fastener without flangeN.m2.44.78.4204280125193280g
kg-m0.240.470.842.04.28.012.519.328
lb-ft2.03.56.014.530.558.090.5139.5202.5
A equivalent of 6.8 strength
fastener with flangeN.m2.44.98.8214484133203298g
kg-m0.240.490.882.14.48.413.320.329.8
lb-ft2.03.56.515.532.061.096.5147.0215.5
A equivalent of 7T strength
fastenerN.m2.34.510235085135210240
kg-m0.230.451.02.35.08.513.52124
lb-ft2.03.57.517.036.561.598.0152.0174.0
A equivalent of 8.8 strength
fastener without flangeN.m3.16.3112756105168258373g
kg-m0.310.631.12.75.610.516.825.837.3
lb-ft2.54.58.019.540.576.0121.5187.0270.0
A equivalent of 8.8 strength
fastener with flangeN.m3.26.512295911 3175270395g
kg-m0.320.651.22.95.911.317.52739.5
lb-ft2.55.09.021.043.082.0126.5195.5286.0

1. Thickness gauge IN
EX
0B-6 MAINTENANCE AND LUBRICATION
Water Pump Belt Replacement
Replace belt with a new one. Refer to SECTION 6B for replacement
procedure of pump belt.
NOTE:
When replacing belt with a new one, adjust belt tension to
5 – 7 mm (0.20 – 0.27 in.).
ITEM 1-2
Camshaft Timing Belt Replacement
Replace belt with new one. Refer to SECTION 6A or 6A1 for re-
placement procedure.
CAUTION:

Do not bend or twist timing belt.

Do not allow timing belt to come into contact with oil, wa-
ter, etc.
ITEM 1-3
Valve Lash Inspection (1.3 liter engine only)
1) Remove cylinder head cover.
2) Inspect intake and exhaust valve lash and adjust as necessary.
Refer to SECTION 6A1 for valve lash inspection and adjustment
procedure.
Valve
lash
(gap)
When cold
(Coolant temperature is
15 – 25C or 59 – 77F)When hot
(Coolant temperature is
60 – 68C or
140 – 154F)
(gap)
specifi-
cation
Intake0.13 – 0.17 mm
(0.005 – 0.007 in.)0.17 – 0.21 mm
(0.007 – 0.008 in.)
cation
Exhaust0.23 – 0.27 mm
(0.009 – 0.011 in.)0.28 – 0.32 mm
(0.011 – 0.013 in.)
Special Tool
(A): 09917-18211
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 8.5 lb-ft)
3) Install cylinder head cover and tighten bolts to specification.

MAINTENANCE AND LUBRICATION 0B-7
Proper Engine Oil Viscosity Chart
1. Oil pan
2. Oil drain plug
1. Oil filter
ITEM 1-4
Engine Oil and Filter Change
WARNING:
New and used engine oil can be hazardous.
Be sure to read “WARNING” in General Precaution in SEC-
TION 0A and observe what in written there.
Use engine oil of SE, SF, SG, SH or SJ grade.
Select the appropriate oil viscosity according to the left chart.
Before draining engine oil, check engine for oil leakage. If any evi-
dence of leakage is found, make sure to correct defective part be-
fore proceeding to following work.
1) Drain engine oil by removing drain plug.
2) After draining oil, wipe drain plug clean. Reinstall drain plug, and
tighten it securely as specified below.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
3) Loosen oil filter by using oil filter wrench (Special tool).
Special Tool
(A): 09915-47330
4) Apply engine oil to new oil filter O-ring.
5) Screw new filter on oil filter stand by hand until filter O-ring con-
tacts mounting surface.
CAUTION:
To tighten oil filter properly, it is important to accurately
identify the position at which filter O-ring first contacts
mounting surface.
6) Tighten filter 3 / 4 turn from the point of contact with mounting sur-
face using an oil filter wrench.
Special Tool
(A): 09915-47330
Tightening Torque (Reference)
(a): 14 N
.m (1.4 kg-m, 10.5 lb-ft)

For A / TFor M / T
MAINTENANCE AND LUBRICATION 0B-9
1) Remove radiator cap when engine is cool.
2) Loosen radiator drain plug (1) to drain coolant.
3) Remove reservoir and drain.
4) Tighten drain plug securely. Also install reservoir.
5) Slowly pour specified amount of coolant to the base of radiator
filler neck, and run engine, with radiator cap removed, until ra-
diator upper hose is hot. This drives out any air which may still
be trapped within cooling system. Add coolant as necessary un-
til coolant level reaches filler throat of radiator. Reinstall radiator
cap.
6) Add coolant to reservoir (1) so that its level aligns with Full mark
(2). Then, reinstall cap to reservoir aligning match marks (3) on
reservoir and cap.
ITEM 1-6
Exhaust System Inspection
WARNING:
To avoid danger of being burned, do not touch exhaust sys-
tem when it is still hot.
Any service on exhaust system should be performed when
it is cool.
When carrying out periodic maintenance or vehicle is raised for oth-
er service, check exhaust system as follows:

Check rubber mountings for damage and deterioration.

Check exhaust system for leakage, loose connections, dents,
and damages.
If bolts or nuts are loose, tighten them to specification. Refer to
SECTION 6K for torque specification of bolts and nuts.

Check nearby body areas for damaged, missing or mispositioned
parts, open seams, holes, loose connections or other defects
which could permit exhaust fumes to seep into vehicle.

Make sure that exhaust system components have enough clear-
ance from underbody to avoid overheating and possible damage
to floor carpet.

Any defects should be fixed at once.