belt SUZUKI SWIFT 2017 5.G Owners Manual

0-3
WARRANTY POLICYMaruti Suzuki India Limited (hereinafter called “Maruti Suzuki”),
warrants that each new Maruti Suzuki vehicle distributed in India
by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer
will be free, under normal use and service, from any defects in
material and workmanship at the time of manufacture SUBJECT
TO THE FOLLOWING TERMS AND CONDITIONS:(1) Qualification:To qualify for this warranty the vehicle must be delivered by a
Maruti Suzuki authorised dealer and set-up, and serviced by a
Maruti Suzuki authorised dealer / service station.(2) Term:The term of the warranty shall be twenty-four (24) months or
40,000 kilometers (whichever occurs first) from the date of
Invoice to the first owner.(3) Maruti Suzuki Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehicle within
the term stipulated above, Maruti Suzuki’s only obligation is to
repair or replace at its sole discretion any part shown to be defec-
tive, with a new part or the equivalent at no cost to the owner for
parts or labour, when Maruti Suzuki acknowledges that such a
defect is attributable to faulty material or workmanship at the time
of manufacture. The owner is responsible for any repair or replace-
ments which are not covered by this warranty.
(4) Limitation:This warranty shall not apply to:
(a) Normal maintenance service required other than the three free services, including without limitation, oil and fluid
changes, headlight aiming, fastener retightening, wheel bal-
ancing, wheel alignment and tyre rotation, cleaning of injec-
tors, adjustments of clutch and valve clearance.
(b) The replacement of normal wear parts including without lim- itation, bulbs, tyres and tubes, spark plugs, belts, hoses, fil-
ters, wiper blades, brushes, contact points, fuses, clutch
disc, brake shoes, brake pads, cable and all rubber parts
(except oil seal and glass run).
(c) Any vehicle which has been used for competition or racing.
(d) Any repairs or replacement required as a result of accidents or collision.
(e) Any defects caused by misuse, negligence, abnormal use or insufficient care.
(f) Any vehicle which has been modified or altered, including
without limitation, the installation of performance accesso-
ries.
(g) Any vehicle on which parts or accessories not approved by
Maruti Suzuki have been used.
(h) Any vehicle which has not been operated in accordance with the operating instructions in this Owner’s Manual and Ser-
vice Booklet.
(i) Any vehicle which has not received, during the warranty term, the service inspections prescribed in this Owner’s Manual
and Service Booklet.
(j) Any vehicle which has been assembled, disassembled, adjusted or repaired by other than an Maruti Suzuki autho-
rised dealer/service station.
(k) Any vehicle which has been used for purposes other than what it was designed for.
(l) Any damage or deterioration caused by industrial pollution and bird droppings.

0-4
55KS0-74E
(m) Insignificant defects which do not affect the function of thevehicle including without limitation, sound, vibration and fluid
seep.
(n) Any natural wear and tear including without limitation, aging
etc.
(o) Installation and usage of domestic LPG gas/LPG Cylinder.
(p) V-belts, hoses and gas leaks.
(q) Any vehicle retrofitted with LPG/CNG kits.(5) Extent of Warranty:This warranty is the entire written warranty given by Maruti Suzuki
for Maruti Suzuki vehicles and no dealer or its or his agent or
employee is authorised to extend or enlarge this warranty and no
dealer or its or his agent or employee is authorised to make any
oral warranty on Maruti Suzuki’s behalf.
Maruti Suzuki reserves the right to add any improvements or
change the design of any model at any time with no obligation to
make the same changes on units previously sold.(6) Warranty Service:To obtain warranty service, th e complete vehicle must be pre-
sented at the owner’s expenses to any authorised Maruti Suzuki
dealer.(7) Owner’s Warranty Responsibilities:It is responsibility of each owner to: – Make certain that the PDl card was completed at the time ofdelivery of the vehicle;
–

Have performed, at his own expenses, by an Maruti Suzuki
authorised dealer/service station all the service inspections
specified in the Maruti Suzuki “Owner’s Manual and Service
Booklet and maintain adequate proof that such service
inspections have been performed.
–
Make certain that the Maruti Suzuki authorised dealer/ser-
vice station performing the service inspection has certified
the work on the “Maintenance Service Record” page in the
“Owner’s Manual and Service Booklet and
–
Present the Maruti Suzuki “Owner’s Manual and Service
Booklet to the authorised Maruti Suzuki dealer whenever
requesting service inspections or warranty service.
If the “Owner’s Manual and Service Booklet should be lost or
destroyed the owner should consult the authorised Maruti Suzuki
dealer from whom the vehicle was purchased for instructions con-
cerning replacement of the “Owner’s Manual and Service Booklet.
(8) Disclaimer of Consequential Damage:Maruti Suzuki assumes no responsibility for loss of vehicle, loss of
time, inconvenience or any other indirect incidental or consequen-
tial damage resulting from the vehicle not being available to the
owner because of any defect covered by this warranty.(9) Change of OwnerEven if ownership of the vehicle changes, the remaining warranty
period is effective for the new owner.

BEFORE DRIVING
74LH0-74E
BEFORE DRIVINGKeys ......................................................................................... 2-1
Door Locks .............................................................................. 2-2
Central Door Locking System (if equipped) ........................ 2-2
Keyless Push Start System Remote Controller/Keyless
Entry System Transmitter ..................................................... 2-6
Security System (Vehicle With Keyless Entry System) ....... 2-12
Security System
(Vehicle With Keyless Push Start System) ........................... 2-20
Windows .................................................................................. 2-22
Mirrors ..................................................................................... 2-23
Heated Rear Window Switch (if equipped) .......................... 2-24
Front Seats .............................................................................. 2-25
Rear Seats ............................................................................... 2-26
Folding Rear Seat (if equipped) ............................................. 2-27
Seat Belts and Child Restraint Systems .............................. 2-28
Driver’s Seat Belt Reminder (if equipped) ........................... 2-32
Supplemental Restraint System (air bags)
(if equipped) ............................................................................ 2-38
Instrument Cluster ................................................................. 2-44
Warning and Indicator Lights ................................................ 2-46
Speedometer ........................................................................... 2-51
Tachometer (if equipped) ...................................................... 2-51
Fuel Gauge .............................................................................. 2-51
Temperature Gauge ............................................................... 2-52
Brightness Control ................................................................. 2-52
Information Display ................................................................ 2-53
Lighting Control Lever ........................................................... 2-60
Headlight Leveling Switch ..................................................... 2-61
Turn Signal Control Lever ..................................................... 2-61
Hazard Warning Switch ......................................................... 2-62
Windshield Wiper and Washer Lever ................................... 2-62
Tilt Steering Lock Lever ......................................................... 2-64
Horn ........................................................................................ 2-64
2

2-14
BEFORE DRIVING
74LH0-74E
GENERAL FEATURES
Illuminated Entry
When vehicle is unlocked, the room lamp
will turn ON to facilitate illuminated entry
into the vehicle. If no door is opened in
about 15 seconds of above operation,
room lamp will fade out.
If any door is opened after 15 seconds, the
room lamp turns ON again and after 15
seconds of closing all doors room lamp will
fade out.
If within 15 seconds after closing all the
doors the driver inserts the key into the key
cylinder, then the room lamp will fade out.
Illuminated Exit
When key is removed from the key cylin-
der,the room lamp will turn ON to facilitate
illuminated exit. If no door is opened in
about 15 seconds of key removal from key
cylinder, the room lamp will fade out.
When door is opened to exit the vehicle,
the room lamp will turn ON again (if it has
turned OFF after 15 seconds of key
removal from key cylinder) and will turn
OFF after 15 seconds of closing all the
doors.
If within 15 seconds of all doors closure,
vehicle is locked by pressing the LOCK
button, the room lamp will fade out.
NOTE: Room lamp will fade out gradually
approximately in 2 seconds.Mute Lock/Unlock
To Lock/Unlock the vehicle without siren
chirps use this function.
a) Press and release the Key LOCK &
UNLOCK buttons simultaneously.
b) Press and release Key LOCK or
UNLOCK button for desired function.
Example: To Lock the system without the
Siren chirp sound, press and release the
Key LOCK & UNLOCK button simultane-
ously, then press and release the Key
LOCK button once.
Auto Rearm
In case of accidental Unlock/Disarm of
vehicle by Key, vehicle will automatically
Lock & Arm within 30 sec. without any indi-
cation. Auto rearm cycle gets canceled if
user does any of the following operation
within 30sec :
1. Open any door (including back door).
2. Open Engine Hood.
3. Key On.Radio Frequency Lock Out
Key Lock/Unlock/Car locator function will
cease to function when Key is inside Key
cylinder.
68LM2
Car locator functionCar locator function helps in locating the
vehicle.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds.
The turn signal lights will blink for about 27
seconds. Also, the siren will sound for
about 27 seconds at the same time. Press
and release the Key LOCK & UNLOCK
button simultaneously to cancel
the car locator function.
NOTE:
The car locator function will not activate
when the key is in the ignition switch or pre
warning / full blast warning by shock sen-
sor or alarm is in activated condition.
Siren on
for 27 sec.Light flashes
for 27 sec.
Adjustable Head Restraints: 3
Seat Belts and Child Restraint Systems: 3

2-15
BEFORE DRIVING
74LH0-74E
Flashing LED Status
The flashing LED always reflects the status
of the system as following.
Intrusion Alert
The system gives a report if it has been
intruded in your absence. Four chirps are
given when UNLOCK button is pressed
after an intrusion. PROGRAMMABLE FEATURES
System has some features which can be
programmed by user according to their
choice.
Drive Lock Mode
Drive lock mode can be programmed by
SPEED LOCK or can be turned OFF. If
drive lock mode is programmed to SPEED
LOCK, all the vehicle doors will lock when
vehicle attains the speed of 15 Km/hr. If
Drive Lock is programmed to OFF, no door
will lock by speed.
NOTE:
In case of SPEED LOCK Mode, if any door
is open while driving, it will get cancelled.
Once vehicle Speed crosses 15 Km/hr, the
LED on Security Switch will blink for 5 sec-
onds as indication of door open.
Drive Unlock Mode
Drive unlock can be programmed to KEY
or can be turned OFF. When programmed
to KEY, turning Ignition ON to OFF then
removing the key from the key cylinder will
unlock all the doors. If drive unlock is pro-
grammed to OFF then no door will unlock
by removing key from key cylinder.
Siren Chirp ON/OFF feature
Siren Chirps can be programmed to ON or
OFF. When siren chirp feature disabled,
siren will not chirp after Arm/Disarm by
LOCK/UNLOCK button. Shock Sensor feature
This is a very important feature of security
system. It enables protection of your vehi-
cle against any major impact. If anybody
tries to intrude into the vehicle, the warning
may trigger. Triggering of the warning is of
two types: pre-warning and full blast warn-
ing. The sensitivity of shock sensor can be
adjusted as desired by the user.
PROCEDURE TO PROGRAM FEATURE
Programming Drive Lock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
One time.
d) Press and hold the Security switch.
e) One chirp sound confirms entry into
Drive Lock programming mode.
f) Press the Key “Lock” button (while hold-
ing the Security switch), a single chirp SYSTEM CONDITION LED STATUS
Disarmed conditionLED does not
glow
Armed conditionSlow Flashes
of LED
Diagnostic
reportVisual-LED Sound
Built in Shock
Sensor Trigger
(full blast warn-
ing)2 FlashesFour
Chirps
Door/Trunk/
Tailgate/Engine
Hood Intrusion3 FlashesFour
Chirps
Ignition 5 FlashesFour
Chirps
No. Feature 1 Chirp 2 Chirps Default
1.Drive Lock
ModeSpeed OFF Speed
2.Drive Unlock
ModeKey OFF Key
3.Siren chirp
ON/OFFON OFF ON
4.Shock Sen-
sor ON/OFFON OFF ON
Seat Belts and Child Restraint Systems: 3

2-16
BEFORE DRIVING
74LH0-74E
sound confirms mode changed to
speed lock.
g) Two-Siren chirp sound confirms Drive
lock mode OFF.
h) Release the Security switch.
i) Turn the Ignition ON.
Programming Drive Unlock Mode
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
two times.
d) Press and hold the Security switch.
e) Two-chirp sound confirms entry into
Drive unlock programming mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
key Unlock.
g) Two-siren chirp sound confirms the
mode changed to Drive Unlock mode
OFF.
h) Release the Security switch.
i) Turn the Ignition ON.Programming Siren Chirp ON/OFF
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
Three times.
d) Press and hold the Security switch.
e) Three-chirp sound confirms entry into
Siren Chirp ON/OFF programming
mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirp
sound confirms the mode changed to
Siren Chirp ON.
g) Two-Siren chirp sound confirms the
mode changed to Siren Chirp OFF.
h) Release the Security switch.
i) Turn the Ignition ON.
Programming Shock Sensor ON/OFF
a) Open the Driver Door of your vehicle.
b) With your vehicle key in the Key cylin-
der, turn Ignition ON and then switch it
OFF.
c) Press and release the Security switch
Four times.
d) Press and hold the Security switch.
e) Four-chirp sound confirms entry into
Shock Sensor ON/OFF programming
mode.
f) Press the Key Lock button (while hold-
ing the Security switch), a single chirpsound confirms the mode changed to
shock sensor ON.
g) Two-Siren chirp sound confirms the
mode changed to shock sensor OFF.
h) Release the Security switch.
i) Turn the Ignition ON.
Shock Sensor Sensitivity Adjustment
via Key
Full Blast adjustment
Full Blast can be adjusted in 16 levels as
mentioned below.
a) Press Unlock button on Key to Unlock/
Disarm the System.
b) Press Lock button (within 2 seconds of
key UNLOCK) on Key to Lock/Arm the
System.
c) Within 2 sec press Lock & Unlock button
simultaneously for at least 3 sec. Siren
will give Long chirp to confirm entry into
sensitivity adjustment mode
i) Press Lock button to adjust the sen-
sitivity one step lower. Siren will give
one chirp every time lock button is
pressed till at level 1 where it will
give a long chirp. When adjusted to
level 1, Full Blast will turn OFF
ii) Press unlock button to adjust the
sensitivity one step higher. Siren will
give two chirp every time unlock but-
ton is pressed till at level 16 where it
will give a long chirp.
Seat Belts and Child Restraint Systems: 3

2-17
BEFORE DRIVING
74LH0-74E
Pre-warn Adjustment
Pre-warn can be adjusted in 16 levels as
mentioned below:
a) Press Lock button on Key to Lock/Arm
the System
b) Press Unlock button (within 2 seconds
of key LOCK) on Key to Unlock/Disarm
the System
c) Within 2 sec press Lock & Unlock button
simultaneously for at least 3 sec. Siren
will give Long chirp to confirm entry into
Sensitivity Adjustment Mode.
i) Press Lock button to adjust the sen-
sitivity one step lower. Siren will give
one chirp every time lock button is
pressed till at level 1 where it will
give a long chirp. When adjusted to
level 1, pre-warn will turn OFF.
ii) Press Unlock button to adjust the
sensitivity one step higher. Siren will
give two Chirp every time Unlock
button is pressed till at level 16
where it will give a long chirp.
Program Customer Pin-code
(Personalized Pin-code)
If transmitter is not working properly, then it
is possible to disarm the system by Per-
sonalized pin code.
The Personalized 4-digit number can be
changed from the factory default to ensure
Personalized Security.Pin code entry
a) Disarm the system.
b) Open the Driver Door.
c) Turn Ignition ON then OFF.
d) Within 5 seconds press and release
Valet switch 5 times. A short chirp fol-
lowed by long chirps confirms entry into
Pin Code programming mode.
e) Press Lock button on Key, after a single
chirp enter the First digit (within 1-9) by
pressing Valet switch (for e.g. to enter 2
press and release Valet switch two
times).
f) Press Lock button on Key, after two
chirp enter the Second digit (within 1-9)
by pressing Valet switch.
g) Press Lock button on Key, after 3-chirps
enter the Third digit (within 1-9) by
pressing Valet switch.
h) Press Lock button on Key, after 4-chirps
enter the Fourth digit (within 1-9) by
pressing Valet switch.
Emergency Disarm by Personalized pin
code
The Personalized 4- Digit Pin Code acts as
a secret Key, to Emergency Disarm the
vehicle.
a) Turn the Ignition ON, OFF and then ON.
b) Enter the First digit (for e. g. to enter 2
press and release Valet switch twice)
c) Turn the Ignition OFF then ON.
d) Enter the Second digit.e) Turn the Ignition OFF and then ON.
f) Enter the Third Digit.
g) Turn the Ignition OFF and then ON
h) Enter the Last Digit.
i) Turn the Ignition OFF and then ON.
j) The vehicle will get disarmed.
NOTE:
The default pin will be provided by the
dealer at the time of delivery. It is recom-
mended to personalize the pin for
increased security. The pin must be
remembered as it is not possible to retrieve
a lost pin.
Seat Belts and Child Restraint Systems: 3

2-18
BEFORE DRIVING
74LH0-74E
Transmitter battery
Replacement of the Battery
If the transmitter battery gets discharged,
replace the battery with a new one.
To replace the battery of the transmitter:
1) Remove the screw (1), and open the
transmitter cover.
2) Remove the transmitter (2).
3) Put the edge of a flat blade screw driver
in the slot of the transmitter (2) and pry
it open.
4) Replace the battery (3) (Lithium disc
type CR1620) so that its +ve terminal
faces the bottom cover of the transmit-
ter (5).5) Close the transmitter and install it into
the transmitter holder.
6) Close the transmitter cover, install and
tighten the screw (1).
7) Make sure the door locks can be oper-
ated with the transmitter.
NOTE:
Normal battery life is approximately 2
years, but varies depending on usage. It is
advisable to get battery replaced from
MARUTI SUZUKI Authorized workshop.CAUTION
Do not remove the screw from the
key Unnecessarily as it damages the
screw head. Kindly replace the screw
once the transmitter battery is
changed.
CAUTION
Dispose off the used battery properly
according to applicable rules or regu-
lations. Do not dispose off lithium
batteries with ordinary household
trash.
WA R N I N G
Swallowing a lithium battery may
cause serious internal injury. Do not
allow anyone to swallow a lithium
battery. Keep lithium batteries away
from children and pets. If swallowed,
contact a physician immediately.
Seat Belts and Child Restraint Systems: 3

2-19
BEFORE DRIVING
74LH0-74E TROUBLESHOOTING
SYMPTOMS PROBABLE CAUSES REMEDIES
Transmitter function (Unlock/Lock/car
locator function) not working 1. Battery of the transmitter is weak.
2. Transmitter is exposed to water or it is
wet.
3. D/L or Dome fuse for controller is blown
in the vehicle.
4. In case if any door is open or door
sensor is shorted with the body ground,
remote will not activate the central
locking/ alarm system.1. Check the battery.
2. Dry the transmitter and check it.
3. Check and replace the D/L or Dome
fuse.
4. Check if all doors are properly closed
and door switch functioning is O.K.
Operation distance of the transmitter is
less than 20m but still transmitter (Unlock/
Lock/car locator) is not working 1. Battery of the transmitter is weak.
2. Strong RF interference. (e.g. Radio
Towers, High Voltage Transmission line
near by)1. Check the battery.
2. Drive the vehicle away from the
particular spot and re-test the control
distance.
It is difficult to activate or deactivate the
system in certain area using the
transmitter. 1. The strong interference caused by
excessive RF activity in a particular
area1. The interference is temporary and only
while the vehicle is in that area.
Alarm is not triggered even if any door(s)/
engine hood/trunk/tailgate opened in arm
stage.1. The contact point of the door(s), front
bonnet or rear boot switch is faulty.
2. The connection of the door(s), front
bonnet or rear boot switch is loose.1. Replace the defective Switch.
2. Make proper connection.
Siren does not sound when alarm is
triggered. 1. The connection of the siren wire is
loose.
2. Siren is faulty. 1. Make proper connection.
2. Change the siren.
Seat Belts and Child Restraint Systems: 3

2-20
BEFORE DRIVING
74LH0-74E
Security System (Vehicle with Key-
less push start system)
The security system is armed after you
lock all doors (including engine hood and
trunk/tailgate) by using the keyless push
start system remote controller or request
switch.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless push start system remote
controller or open the engine hood, will
cause the alarm to be triggered.
* These means include the following:
–The key
– The lock knob on a door
– The central door locking switch
– The tailgate unlatch button (if
equipped)
– The trunk lid unlatch button (if
equipped)
Also, in case that you have set the shock
sensor to enabled state and set sensitivity
of the pre-warning function and full blast
warning function to a level other than 0, the
warning will be triggered in case of any
attempt to tamper with the vehicle. The
shock sensor can be selected enabled or
disabled state, and sensitivity of each
warning can be adjusted as desired. To set
the shock sensor, ask your MARUTI
SUZUKI dealer or use the setting mode of
the information display.NOTE:
• The default setting of the shock sensor
is in the disabled state. Set to the
enabled state and adjust sensitivity of
each warning according to your prefer-
ence. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.
• Your dealer may have already set the
shock sensor of the vehicle to the
enabled state before you purchase it.
Consult your dealer for further informa-
tion.
NOTE:
• The security system generates alarms
when any of the predetermined condi-
tions is met. However, the system does
not have any function of blocking unau-
thorized entry into the vehicle.
• Always use the keyless push start system
remote controller to unlock the doors when
the security system has been armed.
Using a key instead will trigger the alarm.
• If a person who does not know the secu-
rity system is going to drive the vehicle,
we recommend you explain the system
and its operation to the person. Mistak-
enly triggering the alarm may cause a
nuisance to others.
• Even if the security system is armed,
you should still be careful to guard
against theft. Do not leave money or
things of value in the vehicle.How to arm the security system
Lock all doors (including engine hood and
trunk/tailgate) using the keyless push start
system remote controller or request switch.
When the system is armed, the indicator
continues to blink at intervals of approxi-
mately 2 seconds.
79MH0210
NOTE:
• To prevent the alarm from being acci-
dentally triggered, avoid arming it while
anyone remains inside the vehicle. The
alarm will be triggered if any person
inside opens the door, trunk/tailgate,
engine hood, or the warning may be trig-
gered if anyone swings the vehicle (if the
shock sensor is in the enabled state).
• The security system is not armed when
all doors are locked using the key from
outside, using the door lock knobs or the
central door locking switch from inside.
(1)
EXAMPLE
Seat Belts and Child Restraint Systems: 3