ground clearance SUZUKI SX4 2006 1.G Service Owner's Guide
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2006, Model line: SX4, Model: SUZUKI SX4 2006 1.GPages: 1556, PDF Size: 37.31 MB
Page 1093 of 1556
Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-54
DTC B1054 / B1058: Seat Belt Pretensioner Circuit Shorted to Power SupplyS6RW0D8204029
DTC B1054: Driver Seat Belt Pretensioner Circuit Shorted to Power Supply
DTC B1058: Passenger Seat Belt Pretensioner Circuit Shorted to Power Supply
Wiring Diagram
Refer to “DTC B1051 / B1055: Seat Belt Pretensioner Circuit High Resistance”.
DTC Detecting Condition and Trouble Area
DTC Troubleshooting
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
DTC detecting condition Trouble area
DTC B1054:
Driver seat belt pretensioner circuit has been shorted to
power supply for more than 4 sec.
DTC B1058:
Passenger seat belt pretensioner circuit has been shorted
to power supply for more than 4 sec.• Driver / passenger seat belt pretensioner circuit
•SDM
Step Action Yes No
1Was “Air Bag Diagnostic System Check Flow” performed?Go to Step 2. Go to “Air Bag
Diagnostic System
Check Flow”.
2Seat belt pretensioner circuit check
1) With ignition switch turned OFF, remove center pillar
lower trim of applicable side and disconnect applicable
seat belt pretensioner connector “L283” or “L285”.
2) Disconnect SDM connector “L04”.
3) Check for proper connection to applicable seat belt
pretensioner at terminals in “L283” or “L285”.
4) Check for proper connection to SDM at terminals “L04-7”
and “L04-8” (for DTC B1054) or terminals “L04-9” and
“L04-10” (for DTC B1058).
5) If OK, release shorting bar in SDM connector inserting
release tool (1) included in special tool (A).
6) With ignition switch turned ON, measure voltage
between “L04-7” and body ground, and between “L04-8”
and body ground (for DTC B1054).
7) Measure voltage between “L04-9” and body ground and
between “L04-10” and body ground (for DTC B1058).
Special tool
(A): 09932–76010
Is each measured voltage 0 V?Substitute a known-
good SDM and recheck.Repair short to power
supply in defective
circuit.
“L04-8” “L04-9” “L04-10” “L04-7”
1,(A)
(A)
I7RW01822063-01
Page 1100 of 1556
Downloaded from www.Manualslib.com manuals search engine 8B-61 Air Bag System:
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components, ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
DTC B1063 / B1067: Side-Air Bag Circuit Shorted to GroundS6RW0D8204057
DTC B1063: Driver Side-Air Bag Circuit Shorted to Ground
DTC B1067: Passenger Side-Air Bag Circuit Shorted to Ground
Wiring Diagram
Refer to “DTC B1061 / B1065: Side-Air Bag Circuit High Resistance”.
DTC Detecting Condition and Trouble Area
DTC detecting condition Trouble area
DTC B1063:
Driver side-air bag circuit has been shorted to ground for
more than 4 sec.
DTC B1067:
Passenger side-air bag circuit has been shorted to ground
for more than 4 sec.• Driver / passenger side-air bag circuit
•SDM
Page 1102 of 1556
Downloaded from www.Manualslib.com manuals search engine 8B-63 Air Bag System:
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components, ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
3Floor harness circuit check
1) Disconnect applicable “L384” or “L385” connector under
front cushion.
2) Check for proper connection to applicable floor harness
connector at terminal in connector “L384” or “L385”.
3) If OK, release shorting bar in SDM connector inserting
release tool (1) included in special tool (A).
Special tool
(A): 09932–76010
4) Measure resistance between “L04-11” terminal and body
ground, and between “L04-12” terminal and body ground
(for DTC B1063).
5) Measure resistance between “L04-13” terminal and body
ground, and between “L04-14” terminal and body ground
(for DTC B1067).
Is each measured resistance infinity?DTC B1063: Repair
“BLU” circuit or “BLK”
circuit for short to
ground at driver side-air
bag harness.
DTC B1067: Repair
“BLU” circuit or “BLK”
circuit for short to
ground at passenger
side-air bag harness.DTC B1063: Repair
“GRY/RED” circuit or
“GRY” circuit for short to
ground at floor harness.
DTC B1067: Repair
“BRN/WHT” circuit or
“BRN” circuit for short to
ground at floor harness. Step Action Yes No
“L384”, “L385”
“L04-12” “L04-13” “L04-14” “L04-11”
1,(A)
(A)
I7RW01822083-01
Page 1104 of 1556
Downloaded from www.Manualslib.com manuals search engine 8B-65 Air Bag System:
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components, ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
3Floor harness circuit check
1) Disconnect applicable “L384” or “L385” connector under
front cushion.
2) Check for proper connection to applicable floor harness
connector at terminal in connector “L384” or “L385”.
3) If OK, release shorting bar in SDM connector inserting
release tool (1) included in special tool (A).
Special tool
(A): 09932–76010
4) With ignition switch turned ON, measure voltage
between “L04-11” terminal and body ground, and
between “L04-12” terminal and body ground (for DTC
B1064).
5) Measure voltage between “L04-13” terminal and body
ground, and between “L04-14” terminal and body ground
(for DTC B1068).
Is each measured voltage 0 V?DTC B1064: Repair
“BLU” circuit or “BLK”
circuit for short to power
supply circuit at driver
side-air bag harness.
DTC B1068: Repair
“BLU” circuit or “BLK”
circuit for short to power
supply circuit at
passenger side-air bag
harness.DTC B1064: Repair
“GRY/RED” circuit or
“GRY” circuit for short to
power supply circuit at
floor harness.
DTC B1068: Repair
“BRN/WHT” circuit or
“BRN” circuit for short to
power supply circuit at
floor harness. Step Action Yes No
“L384”, “L385”
“L04-12” “L04-13” “L04-14” “L04-11”
1,(A)
(A)
I7RW01822085-01
Page 1107 of 1556
Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-68
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
DTC B1074: Driver Forward Impact-Sensor Circuit OpenS6RW0D8204037
Wiring Diagram
Refer to “DTC B1073: Driver Forward Impact-Sensor Circuit Shorted to Ground”.
DTC Detecting Condition and Trouble Area3Forward impact-sensor circuit check
1) Measure resistance between “L04-50” and “L04-51”
terminals.
Special tool
(A): 09932–76010
Is each measured resistance infinity?Replace defective
forward impact-sensor,
and recheck.
If this DTC is still
detected, replace SDM.Repair short to ground
in defective circuit. Step Action Yes No
“L04-50”“L04-51”
(A)
I7RW01821028-01
DTC detecting condition Trouble area
Forward impact-sensor circuit has been shorted to power
circuit or opened for more than 4 sec.• Forward impact-sensor
• Forward impact-sensor circuit
•SDM
Page 1108 of 1556
Downloaded from www.Manualslib.com manuals search engine 8B-69 Air Bag System:
DTC Troubleshooting
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
Step Action Yes No
1Was “Air Bag Diagnostic System Check Flow” performed?Go to Step 2. Go to “Air Bag
Diagnostic System
Check Flow”.
2Forward impact-sensor circuit check
1) Disconnect forward impact-sensor connector “E40”.
2) Disconnect SDM connector “L04”.
3) Check for proper connection to SDM connector at
terminals “L04-50” and “L04-51”.
4) Check for proper connection to forward impact-sensor
connector at terminals “E40-1” and “E40-2”.
5) Measure resistance between “L04-50” and “E40-2”
terminals, between “L04-51” and “E40-1” terminals.
Special tool
(A): 09932–76010
Is each measured resistance 1
Ω or less?Go to Step 3. Repair high resistance
or open in defective
circuit.
3Forward impact-sensor circuit check
1) With ignition turned ON, measure voltage between “L04-
50” terminal and body ground, between “L04-51”
terminal and body ground.
Special tool
(A): 09932–76010
Is each measured voltage 0 V?Replace forward
impact-sensor, and
recheck.
If DTC still detected,
replace SDM.Repair short to power
supply circuit or other
circuit in defective
circuit.
“L04-50”“L04-51”
“E40-1”
“E40-2”
(A)
I7RW01822067-02
“L04-50”“L04-51”
(A)
I7RW01821029-01
Page 1110 of 1556
Downloaded from www.Manualslib.com manuals search engine 8B-71 Air Bag System:
DTC Troubleshooting
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
DTC B1083 / B1093: Side Impact-Sensor Circuit Shorted to GroundS6RW0D8204059
DTC B1083: Driver Side Impact-Sensor Circuit Shorted to Ground
DTC B1093: Passenger Side Impact-Sensor Circuit Shorted to Ground
Wiring Diagram
DTC Detecting Condition and Trouble AreaStep Action Yes No
1Was “Air Bag Diagnostic System Check Flow” performed?Go to Step 2. Go to “Air Bag
Diagnostic System
Check Flow”.
2DTC check
1) Connect scan tool to DLC with ignition switch turned
OFF.
2) Turn ON ignition switch and check SDM for DTC.
Are there any DTC(s) B1083, B1084, B1085 (for DTC
B1082) or B1093, B1094, B1095 (for DTC B1092)?Go to applicable DTC
diag. flow.Replace defective side
impact-sensor and
recheck.
If this DTC still detected,
replace SDM.
10
“L04”30V
30VL04-47 L04-46WHT/RED
LT GRN/BLK“L36”
11
L04-44 L04-45WHT/GRN
LT GRN
“L35”12
“L04”
BLK
L04-28
6 8
7
RED
GRN“L313”L04-27
9
1
2 BLKWHT3
4
5
13
12V5V30V
14
I6RW0C820013-01
1. Battery 5. Individual circuit fuse box No.1 9. Ground for air bag system 13. DC / DC converter
2. Fuse 6. Ignition switch 10. SDM 14. Back up capacitor
3. Main fuse box 7. “A/B” fuse 11. Driver side impact-sensor
4. “IGN” fuse 8. Junction block assembly 12. Passenger side impact-sensor
DTC detecting condition Trouble area
DTC B1083:
Driver side impact-sensor circuit has been shorted to
ground for more than 4 sec.
DTC B1093:
Passenger side impact-sensor circuit has been shorted to
ground for more than 4 sec.• Driver / passenger side impact-sensor circuit
• Driver / passenger side impact-sensor
•SDM
Page 1111 of 1556
Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-72
DTC Troubleshooting
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
Step Action Yes No
1Was “Air Bag Diagnostic System Check Flow” performed?Go to Step 2. Go to “Air Bag
Diagnostic System
Check Flow”.
2Side impact-sensor circuit check
1) Disconnect applicable side impact-sensor connector
“L35” or “L36”.
2) Disconnect SDM connector “L04”.
3) Check for proper connection to SDM connector at
terminals “L04-46” and “L04-47” (for DTC B1083) or
terminals “L04-44” and “L04-45” (for DTC B1093).
4) Check for proper connection to applicable side impact-
sensor connector at terminals in connector “L35” or
“L36”.
5) Measure resistance between “L04-46” terminal and body
ground (for DTC B1083) or between “L04-45” terminal
and body ground (for DTC B1093).
Special tool
(A): 09932–76010
Is each measured resistance infinity?Go to Step 3. Repair short to ground
in defective circuit.
3Side impact-sensor circuit check
1) Measure resistance between “L04-46” and “L04-47”
terminals, between “L04-46” and “L04-44” terminals (for
DTC B1083).
2) Measure resistance between “L04-45” and “L04-44”
terminals, between “L04-45” and “L04-47” terminals (for
DTC B1093).
Special tool
(A): 09932–76010
Is each measured resistance infinity?Replace defective side
impact-sensor, and
recheck.
If this DTC is still
detected, replace SDM.Repair short to ground
in defective circuit.
(A)
“L04-44”“L04-45” “L04-46” “L04-47”
I7RW01822069-01
“L04-44”“L04-45” “L04-46” “L04-47”
(A)
I7RW01822070-01
Page 1113 of 1556
Downloaded from www.Manualslib.com manuals search engine Air Bag System: 8B-74
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
DTC B1085 / B1095: Side Impact-Sensor Communication DATA InconsistentS6RW0D8204061
DTC B1085: Driver Side Impact-Sensor Communication DATA Inconsistent
DTC B1095: Passenger Side Impact-Sensor Communication DATA Inconsistent
DTC Detecting Condition and Trouble Area
DTC Troubleshooting3Side impact-sensor circuit check
1) With ignition turn ON, measure voltage between “L04-
46” terminal and body ground, between “L04-47”
terminal and body ground (for DTC B1084).
2) Measure voltage between “L04-45” terminal and body
ground, between “L04-44” terminal and body ground (for
DTC B1094).
Special tool
(A): 09932–76010
Is each measured voltage 0 V?Replace side impact-
sensor, and recheck.
If DTC still detected,
replace SDM.Repair short to power
supply circuit or other
circuit in defective
circuit. Step Action Yes No
“L04-44”“L04-45” “L04-46” “L04-47”
(A)
I7RW01822072-01
DTC detecting condition Trouble area
DTC B1085:
Driver side impact-sensor has been communicated with
inconsistent ID code for more than 4 sec.
DTC B1095:
Passenger side impact-sensor has been communicated
with inconsistent ID code for more than 4 sec.• Driver / passenger side impact-sensor
•SDM
Step Action Yes No
1Was “Air Bag Diagnostic System Check Flow” performed?Go to Step 2. Go to “Air Bag
Diagnostic System
Check Flow”.
2DTC check
1) Connect scan tool to DLC with ignition switch turned
OFF.
2) Turn ON ignition switch and clear DTC referring to “DTC
Clearance”.
3) Turn OFF ignition switch and recheck DTC.
Is DTC(s) B1085 and/or B1095 still detected?Replace defective side
impact-sensor.Intermittent trouble.
Check for intermittent
trouble referring to
“Inspection of
Intermittent and Poor
Connections”.
Page 1114 of 1556
Downloaded from www.Manualslib.com manuals search engine 8B-75 Air Bag System:
NOTE
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance”, if any.
• Repeat “Air Bag Diagnostic System Check” to confirm that the trouble has been corrected.
DTC B1361 / B1365: Curtain-Air Bag Circuit High ResistanceS6RW0D8204062
DTC B1361: Driver Curtain-Air Bag Circuit High Resistance
DTC B1365: Passenger Curtain-Air Bag Circuit High Resistance
Wiring Diagram
DTC Detecting Condition and Trouble Area
10
L04-20
L04-19
L04-21
L04-22
YEL/GRN
YEL/BLU
BLK/YEL
BRN/YELYEL/GRN
YEL/BLU
BLK/YEL
BRN/YEL “L395” “Q132”
11
12
“L04”
“Q102” “Q103”
“L04”
BLK
L04-28
6 8
7
RED
GRN“L313”L04-27
9
1
2 BLKWHT3
4
5
[A]
13
12V5V30V
14
I6RW0C820014-01
[A]: Shorting bar 5. Individual circuit fuse box No.1 10. SDM
1. Battery 6. Ignition switch 11. Driver side curtain-air bag (inflator) module
2. Fuse 7. “A/B” fuse 12. Passenger side curtain-air bag (inflator) module
3. Main fuse box 8. Junction block assembly 13. DC / DC converter
4. “IGN” fuse 9. Ground for air bag system 14. Back up capacitor
DTC detecting condition Trouble area
DTC B1361:
Driver curtain-air bag circuit is more than 3.8 Ω for more
than 4 sec.
DTC B1365:
Passenger curtain-air bag circuit is more than 3.8 Ω for
more than 4 sec.• Driver / passenger curtain-air bag circuit
• Driver / passenger curtain-air bag module
•SDM