oil TATA SAFARI 2015 Owner's Manual
[x] Cancel search | Manufacturer: TATA, Model Year: 2015, Model line: SAFARI, Model: TATA SAFARI 2015Pages: 161, PDF Size: 2.55 MB
Page 109 of 161
109
FUEL FIL FUEL FILFUEL FIL FUEL FIL
FUEL FIL
TER & FUEL SY TER & FUEL SYTER & FUEL SY TER & FUEL SY
TER & FUEL SY
STEM STEMSTEM STEM
STEM
6. Refit the drain plug using a new sealing washer. Tighten
drain plug to 5 mkg. torque.
7. Fill, recommended quantity of fresh engine oil in the crank
case and secure the oil filler cap in its place.
8. Start the engine and run for a few minutes. The engine oil
pressure indicator lamp should go ‘off ’ after starting the
engine.
9. Check for engine oil leakages.
10. Stop the engine and recheck engine oil level after a few
minutes. If necessary add oil to bring the level to the upper
mark on the dipstick.
NOTICE NOTICENOTICE NOTICE
NOTICE
Use of reclaimed oil is not recommended
Priming Pump Priming PumpPriming Pump Priming Pump
Priming Pump
Priming pump is used for priming the fuel manually after
overhauling of the engine or after refitment of fuel lines. Pump
the fuel by means of priming pump until all air in the fuel line is
removed. Before cranking the engine ensure that there is no air
in the fuel system.
NOTICE NOTICENOTICE NOTICE
NOTICE
Please do not loosen/remove high pressure pipes and injectors
for air bleeding in the fuel.
M A I N T E N A N C E
F FF F
F
uel & F uel & Fuel & F uel & F
uel & F
ilt iltilt ilt
ilt
er D er Der D er D
er D
r rr r
r
aining ainingaining aining
aining
Loosen drain plugs by 1-2 turn and drain out water and other
sediments from fuel filter bowls depending on operating
conditions to ensure that no water is allowed to enter the fuel
system.
S SS S
S
edimen edimenedimen edimen
edimen
t tt t
t
er er er er
er
W WW W
W
a aa a
a
t tt t
t
er D er Der D er D
er D
r rr r
r
aining ainingaining aining
aining
Water sedimenter is located near fuel tank at rear left hand side
of the vehicle.
Loosen drain plug by 1-2 turns and drain out water and other
sediments from sedimenter when water level indicator lamp
glows in instrument cluster to ensure that no water is
allowed to enter the fuel system.
Sedimenter
ProCarManuals.com
Page 110 of 161
110
Gear Box Oil Gear Box OilGear Box Oil Gear Box Oil
Gear Box Oil
C CC C
C
heck heckheck heck
heck
ing of Oil L ing of Oil Ling of Oil L ing of Oil L
ing of Oil L
e ee e
e
v vv v
v
el elel el
el
1. Clean the oil level plug and surrounding area.
2 . Remove the oil level plug and check whether oil is dripping out.
Oil level must not be below the filler plug. Add oil to bring it to
the level.
3. Tighten oil level plug to 2-3 mkg. torque.
C CC C
C
hanging Oil in G hanging Oil in Ghanging Oil in G hanging Oil in G
hanging Oil in G
ear B ear Bear B ear B
ear B
o oo o
o
x xx x
x
1. Let the engine idle for about 5 min. in neutral, so that the gear box
oil is warmed up.
2. Clean the oil level plug, drain plug and surrounding area.
3. Place a container under gear box to collect the oil.
4. Remove the drain plug and let the oil drain out.
5. Also remove the oil level plug.
6. Tighten the oil drain plug and fill new recommended oil through oil
level plug and tighten the oil drain plug oil level plug to 2-3 mkg.
torque.
GEAR BO GEAR BOGEAR BO GEAR BO
GEAR BO
X OIL X OILX OIL X OIL
X OIL
1. Gear Box Oil Filler Plug / Level Plug
2. Gear Box Drain Plug
1
2
M A I N T E N A N C E
ProCarManuals.com
Page 111 of 161
111
TRANSFER CASE OIL TRANSFER CASE OILTRANSFER CASE OIL TRANSFER CASE OIL
TRANSFER CASE OIL
C CC C
C
heck heckheck heck
heck
ing Oil L ing Oil Ling Oil L ing Oil L
ing Oil L
e ee e
e
v vv v
v
el of el of el of el of
el of
T TT T
T
r rr r
r
ansf ansfansf ansf
ansf
er C er Cer C er C
er C
ase asease ase
ase
NO NONO NO
NO
TICE TICETICE TICE
TICE
Before checking or removing the oil, warming up of the transfer
case is necessary. This should be done by driving the vehicle for
some time in 4x4 mode.
Checking of Oil levels Checking of Oil levelsChecking of Oil levels Checking of Oil levels
Checking of Oil levels
1. Clean the oil level plug and surrounding area.
2 . Remove the oil level plug and check whether oil is dripping out.
3 . If oil is not dripping out, oil level must be below the required
level. Add oil to bring it to the level when it starts dripping out.
4. Tighten oil level plug. Tightening torque of oil level plug is 2 to
3 mkg.
C CC C
C
hanging of hanging of hanging of hanging of
hanging of
T TT T
T
r rr r
r
ansf ansfansf ansf
ansf
er C er Cer C er C
er C
ase Oil ase Oilase Oil ase Oil
ase Oil
1. Clean the oil level plug, drain plug and surrounding area.
2. Place a container to collect oil, under transfer case.
3. Remove the drain plug and let the oil drain out.
4. Remove the oil level plug.
5. Tighten oil drain plug and fill new recommended oil through oil
level plug, till it begins to drip out.
6. Tighten oil level plug. Tightening torque of oil drain plug is 2 to 3 mkg.
1. Transfer case Oil Filler Plug / Level Plug
2. Transfer case Oil Drain Plug
1
2
M A I N T E N A N C E
ProCarManuals.com
Page 112 of 161
112
Checking Oil Level in Front/Rear Axle Checking Oil Level in Front/Rear AxleChecking Oil Level in Front/Rear Axle Checking Oil Level in Front/Rear Axle
Checking Oil Level in Front/Rear Axle
1 . Clean the oil level plug and surrounding area.
2. Remove the oil level plug and check whether oil is dripping
out. Oil level must be below the required level. Add oil to bring
it to the level, when it starts dripping out.
3 . Tighten oil level plug to 2 to 3 mkg. torque.
Changing Oil in Front Axle/Rear Axle Changing Oil in Front Axle/Rear AxleChanging Oil in Front Axle/Rear Axle Changing Oil in Front Axle/Rear Axle
Changing Oil in Front Axle/Rear Axle
1 . Clean the oil level plug, drain plug and surrounding area.
2 . Place a container under Front/Rear axle to collect the oil.
3 . Remove the drain plug and let the oil drain out.
4 . Also remove the oil level plug.
5 . Tighten the oil drain plug and fill new recommended oil through
oil level plug till it begin to drip.
6 . Tighten oil drain and oil level plugs to 2 to 3 mkg. torque.
FRONT AXLE AND REAR AXLE OIL FRONT AXLE AND REAR AXLE OILFRONT AXLE AND REAR AXLE OIL FRONT AXLE AND REAR AXLE OIL
FRONT AXLE AND REAR AXLE OIL
1. Front Axle Oil Filler Plug / Level Plug
2. Front Axle Oil Drain Plug
1
2
M A I N T E N A N C E
ProCarManuals.com
Page 114 of 161
114
Head Lamp Bulb Replacement Head Lamp Bulb ReplacementHead Lamp Bulb Replacement Head Lamp Bulb Replacement
Head Lamp Bulb Replacement
Raise the bonnet of the vehicle. Unscrew & pull out the rear
protective cover. Pull out the cable socket from the bulb. Remove
locking lever holding the bulb and remove the bulb.
Install new bulb, properly locating it in the housing. Fit back the locking
lever cable socket and rubber cap.
Repeat the same procedure for pencil beam lamp.
Realign Head Lamp after Replacing Bulb Realign Head Lamp after Replacing BulbRealign Head Lamp after Replacing Bulb Realign Head Lamp after Replacing Bulb
Realign Head Lamp after Replacing Bulb
Do not clean or touch the reflector as it will damage the mirror finish
of the surface.
Your vehicle has halogen head lamp bulb and pencil beam bulb one
each on each side. When replacing, handle it by steel base. Protect
the glass from contact with your skin or hard object. If you touch glass,
clean it with denatured alcohol and clean cloth.
NOTICE NOTICENOTICE NOTICE
NOTICE
Halogen head lamp bulbs get very hot when lit. Oil perspiration or a
scratch on the glass can cause the bulb to overheat and shatter.
HEAD L HEAD LHEAD L HEAD L
HEAD L
AMPS AMPSAMPS AMPS
AMPSM A I N T E N A N C E
Ajusting Screw Ajusting ScrewAjusting Screw Ajusting Screw
Ajusting ScrewLevelling LevellingLevelling Levelling
Levelling
motor motormotor motor
motor
adjustment adjustmentadjustment adjustment
adjustment
ProCarManuals.com
Page 116 of 161
116
POWER STEERING POWER STEERINGPOWER STEERING POWER STEERING
POWER STEERING
Procedure for Oil Filling and Bleeding of Power Procedure for Oil Filling and Bleeding of PowerProcedure for Oil Filling and Bleeding of Power Procedure for Oil Filling and Bleeding of Power
Procedure for Oil Filling and Bleeding of Power
Steering SteeringSteering Steering
Steering (Ensure that Power Steering fluid reservoir is totally
clean before starting the work)
1 . Fill the reservoir nearly full. Crank the engine for 10
seconds without allowing it to start (if possible). If engine
does start, shut the engine immediately. Check & refill
the reservoir repeat atleast three times, each time
checking & refilling the reservoir.
2 . Check for leakage in the system and if noticed take
corrective action.
3 . Start the engine and steer the vehicle from full left to full
right turns 3-4 times.
4 . Add fluid if necessary to maintain the level upto filter top.
NOTICE NOTICENOTICE NOTICE
NOTICE
Do not force the wheel against lock position either
extreme left or right. The power steering pump may get
damaged. Hold it lightly.
5 . When the engine is at steady speed, check for bubble
or foaming in the oil. If present it indicates that air is
getting sucked into the systems. Check the suction
line/fittings and correct if necessary.
6 . Once the system is bled properly and free from foaming
there should not be any appreciable change in oil level
in the reservoir, when the engine is started or stopped
repeatedly.
7 . Now the system is ready for driving.
Final oil level should be at ‘H’ mark on dip stick.
NOTICE NOTICENOTICE NOTICE
NOTICE
* Do not allow fluid level to drop significantly or run out
of the reservoir during the above operation. This may
induce air to the system.
* Do not start the engine without oil in the power steering
system. This will result in serious damage to the
pump. In case of emergency disconnect the pump belt
and then start the engine.
* Always use recommended oil from closed containers.
Any dirty oil poured in the system will result in damage
to pump and gear box.
M A I N T E N A N C E
ProCarManuals.com
Page 125 of 161
125
R RR R
R
epair epairepair epair
epair
ing a ing a ing a ing a
ing a
T TT T
T
yr yryr yr
yr
e ee e
e
•Mark suitability the tyre position (if original colour dot mark is
not visible) with reference to valve stem hole to ensure that the
tyre is refitted in original location.
•Ensure that balancing weights are not disturbed during removal
of tyres.
•Check the balance weight prior to removal of tyre if found loose,
mark its location on rim & refit properly. Balance the wheel after
every dismantling and assembly of tyre on wheel rim.
•Tightening torque of wheel nut is 12-15 mkg.
•While fitting wheels on vehicle ensure that wheel bolts are free
from dust, scratches, dirt, dents, etc.
•Do not apply any oil on the wheel nut or bolt. Wipe off if present.
T TT T
T
YRES YRESYRES YRES
YRESM A I N T E N A N C E
ProCarManuals.com
Page 126 of 161
126
VEHICLE C VEHICLE CVEHICLE C VEHICLE C
VEHICLE C
ARE AREARE ARE
ARE
Polishes : Polishes :Polishes : Polishes :
Polishes :
Polishes and cleaners can restore shine to the painted surface
that has oxidised and become dull. They normally contain mild
abrasives and solvents that remove the top layer of the finish
coat. Polish your car if the finish does not regain its original shine
after using wax.
Cleaning of Carpets : Cleaning of Carpets :Cleaning of Carpets : Cleaning of Carpets :
Cleaning of Carpets :
Vacuum clean the carpet regularly to remove dirt. Dirt will make
the carpet wear out faster. Periodically shampoo the carpet to
keep it looking new.
Use carpet cleaners (preferably foam type). Follow the
instructions that come with the cleaner, applying it with a
sponge or soft brush. Keep the carpeting as dry as possible
by not adding water to the foam.
Cleaning of Windows, Front & Rear Glasses : Cleaning of Windows, Front & Rear Glasses :Cleaning of Windows, Front & Rear Glasses : Cleaning of Windows, Front & Rear Glasses :
Cleaning of Windows, Front & Rear Glasses :
Clean the windows inside and outside with commercially
available glass cleaners.
This will remove the haze that builds up on the inside of
windows. Use a soft cloth or paper towels to clean all glass and
plastic surfaces.VEHICLE CARE : VEHICLE CARE :VEHICLE CARE : VEHICLE CARE :
VEHICLE CARE :
The car is subjected to many external influences such as climate,
road conditions, industrial pollution and proximity to the sea.
These conditions demand regular care of the car body. Dirt,
insects, bird droppings, oil, grease, fuel and stone chippings should
be removed as soon as possible.
W WW W
W
ashing : ashing :ashing : ashing :
ashing :
Do not wash the car in direct sunlight, wash in shade. Spray the
car thoroughly with a cold water jet (car on a washing pit or
hoist). Mix car shampoo in the wash water. No solvent (fuel,
thinners) need be used.
NOTICE NOTICENOTICE NOTICE
NOTICE
Avoid wiping of painted surface in dry condition as it may
leave scratches on the painted surface.
Use a soft bristle brush, sponge or soft cloth and rinse it
frequently while washing. When you have washed the whole
exterior, dry it with a chamois or soft cloth. After drying the car,
inspect it for chips and scratches that could allow corrosion to
start. Apply touch up paint where necessary.
For vehicles with Rear View Camera : Use cover for camera For vehicles with Rear View Camera : Use cover for cameraFor vehicles with Rear View Camera : Use cover for camera For vehicles with Rear View Camera : Use cover for camera
For vehicles with Rear View Camera : Use cover for camera
during washing. during washing.during washing. during washing.
during washing.
M A I N T E N A N C E
ProCarManuals.com
Page 129 of 161
129
VEHICLE C VEHICLE CVEHICLE C VEHICLE C
VEHICLE C
ARE AREARE ARE
ARE
W WW W
W
A AA A
A
XING : XING :XING : XING :
XING :
Waxing and polishing is recommended to maintain the gloss
and wet-look appearance of your paint finish.
1. Use a good quality polish and wax for your vehicle.
2. Re-wax your vehicle when the water does not slip off the
surface and collects over the surface in patches.
Further tips for the care of your new vehicle finish : Further tips for the care of your new vehicle finish :Further tips for the care of your new vehicle finish : Further tips for the care of your new vehicle finish :
Further tips for the care of your new vehicle finish :
If your vehicle is washed in an automatic car wash, please
remember that the paint can be scratched by type of brushes,
unfiltered washing water or the washing process itself.
Scratching reduces paint durability and gloss, especially on
darker colours. It is suggested to wash the vehicle by hand with
cool and clean water using a soft cloth or sponge. Please do not
use soap but a car shampoo recommended by your dealer.
Please take the following precautions : Please take the following precautions :Please take the following precautions : Please take the following precautions :
Please take the following precautions :
1. Always wash your vehicle in shade, avoiding direct exposure
to sunlight during washing.
2. Dry wiping your vehicle may lead to the formation of
scratches and hence always use a soft cloth and clean water
while wiping your vehicle.
3. Always keep your vehicle parked in a well ventilated shade.
Exposure to heat with entrapped moisture promotes corrosion.4. Avoid driving on gravel roads, as the possibility of paint
chip off due to the impact of stones is high. If you are
driving on freshly tarred road, check immediately
afterwards for any stains & clean them.
5. External contamination in the form of sap or industrial
fall-out may mar or develop spots on a new finish. Hence
avoid parking your vehicle near trees, which are known
to drop sap, or near factories, which give out heavy smoke.
6. The acid content in bird droppings may damage the newly
painted finish and hence any bird dropping must be
immediately washed off.
7. The paint finish is susceptible to damage in case petrol,
brake fluid, liquid from car battery, oil, antifreeze,
transmission fluid or windshield solvent spills onto the
painted surface. In case of such a spillage immediately
rinse the affected area with water. Avoid wiping the area
far as possible, however if wiping is required, ensure that
you wipe the area gently with soft cotton cloth.
8. Avoid using sharp objects to scrap off tar or mud from a
painted surface as it may develop scratches or may peel
off the paint.
M A I N T E N A N C E
ProCarManuals.com
Page 133 of 161
133
TURBO CHARGER (IF FITTED) TURBO CHARGER (IF FITTED)TURBO CHARGER (IF FITTED) TURBO CHARGER (IF FITTED)
TURBO CHARGER (IF FITTED)
V VV V
V
ar arar ar
ar
iable iable iable iable
iable
T TT T
T
urbine urbine urbine urbine
urbine
T TT T
T
echnolo echnoloechnolo echnolo
echnolo
g gg g
g
y- y- y- y-
y-
VT VTVT VT
VT
T T T T
T
T TT T
T
urb urburb urb
urb
o oo o
o
char charchar char
char
ger : ger :ger : ger :
ger :
Your vehicle is fitted with a turbocharger having variable
turbine technology ( VTT ). Turbocharger is an efficient
supercharging device used in our engine. It makes optimal
use of thermal energy of engine exhaust gases to run a
turbine which in turn drives a compressor to force air under
pressure into the inlet manifold. This turbocharger is
optimized for higher power output flat torque across large
engine speed range and better fuel consumption.
L LL L
L
ubr ubrubr ubr
ubr
ic icic
ic
ic
a aa a
a
tion of tion of tion of tion of
tion of
T TT T
T
urb urburb urb
urb
o oo o
o
char charchar char
char
ger : ger :ger : ger :
ger :
The turbocharger rotor assembly is supported by two fully
floating bearing bushes in the bearing housing. These
bearing bushes are lubricated with finely filtered engine
oil from the lubrication system of the engine.
Idle the engine for a while (30 seconds) after starting the
engine and before stopping the engine to ensure adequate
lubricating oil supply to the turbocharger.
T TT T
T
urb urburb urb
urb
o oo o
o
char charchar char
char
ger C ger Cger C ger C
ger C
onnec onneconnec onnec
onnec
tions : tions :tions : tions :
tions :
All turbocharger connections must be leak-proof. Check air
inlet, air outlet, exhaust gas inlet and exhaust outlet
connections as well as oil inlet and outlet connections to
the turbocharger and tighten the connections where
required.Proper maintenance of air filter, oil filter as well as use of
correct grade of oil and adherence to oil change intervals is
essential for proper functioning of the turbocharger.
If you suspect any malfunctioning of the turbocharger, take
the vehicle to the nearest dealer. Do not remove the
turbocharger yourself.
M A I N T E N A N C E
Turbocharger ( VTT )
ProCarManuals.com