automatic transmission TOYOTA 4RUNNER 1998 User Guide

4RUNNER (1998)
Your automatic transmission has a
shift lock system to minimize the pos-
sibility of incorrect operation. This
means you can only shift out of ºPº
position when the brake pedal is de-
pressed (with the ignition switch in
ºONº position and the lock release
button depressed).
(a) Normal driving
1. Start the engine as instructed in
ºHow to start the engineº in Part 3.
The transmission must be in ºPº or
ºNº.
When the front drive control lever is
in ºL4º (low- speed position, four-
wheel drive), the driving pattern selec-
tor setting has no effect on gear shift
timing. (See ºFour- wheel drive sys-
temº in this Chapter for information of
the front drive control lever.)
2. With your foot holding down the
brake pedal, shift the selector lever to
ºDº.
In ºDº position, the automatic trans-
mission system will select the most
suitable gear for running conditions
such as normal cruising, hill climbing,
hard towing, etc. Always turn the overdrive switch on
for better fuel economy and quieter
driving. If the engine coolant tempera-
ture is low or when the front drive
control lever is in ºL4º (low- speed
position, four- wheel drive), the trans-
mission will not shift into
the overdrive gear even with the over-
drive switch on. (See ºFour- wheel
drive systemº in this Chapter for in-
formation of the front drive control le-
ver.)
CAUTION
Never put your foot on the accel-
erator pedal while shifting.
3. Release the parking brake and
brake pedal. Depress the accelerator
pedal slowly for smooth starting.
(b) Using engine braking
To use engine braking, you can down-
shift the transmission as follows:
Turn off the overdrive switch. The
ºO/D OFFº indicator light will come
on and the transmission will down-
shift to the third gear.
Shift into the º2º position. The
transmission will downshift to the
second gear when the vehicle
speed drops down to or lower than
the following speed, and more pow-
erful engine braking will be ob-
tained.
Front drive control lever in ºH2º or
ºH4º
3RZ- FE engine.....105 km/h (65
mph)
5VZ- FE engine.....114 km/h (70
mph)
Front drive control lever in ºL4º
3RZ- FE engine.....38 km/h (23
mph)
5VZ- FE engine.....41 km/h (25
mph)
Shift into the ºLº position. The
transmission will downshift to the
first gear when the vehicle speed
drops down to or lower than the
following speed, and maximum en-
gine braking will be applied.
Front drive control lever in ºH2º or
ºH4º
3RZ- FE engine.....51 km/h (31
mph)
5VZ- FE engine.....55 km/h (34
mph)

4RUNNER (1998)
Front drive control lever in ºL4º 3RZ- FE engine.....11 km/h (6
mph)
5VZ- FE engine.....12 km/h (7
mph) Vehicles with cruise control
'When the
cruise control is being used, even if
you downshift the transmission by
turning off the overdrive switch, en-
gine braking is not applied because
the cruise control is not cancelled.
For ways to decrease the vehicle
speed, see Cruise control in this
chapter.
CAUTION
Be careful when downshifting on
a slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
(c) Using the º2º and ºLº, posi-
tions
The º2º and ºLº positions are used for
strong engine braking as described
previously.
With the selector lever in º2º or ºLº,
you can start the vehicle in motion as
with the lever in ºDº.
With the selector lever in º2º, the ve-
hicle will start in the first gear and
automatically shift to the second gear.
With the selector lever in ºLº, the
transmission is engaged in the first
gear.

4RUNNER (1998)
NOTICE
Be careful not to overrev the
engine. Watch the tachometer tokeep engine rpm from goinginto the red zone. The approxi-
mate maximum allowable speedfor each position is given abovefor your reference:
Front drive control lever inºH2º or ºH4º
3RZ- FE engine º2º.....................111km/h (68
mph)
ºLº...................... 60km/h (37
mph)
5VZ- FE engine º2º.....................1 18km/h (73
mph)
ºLº...................... 64km/h (40
mph)
Front drive control lever in ºL4º
3RZ- FE engine º2º...................... 43km/h (26
mph) ºLº...................... 23km/h (14
mph)
5VZ- FE engine º2º...................... 46km/h (28
mph)
ºLº...................... 25km/h (15
mph)
Do not continue hill climbing or
hard towing for a long time inthe º2º or ºLº position. Thismay cause severe automatic
transmission damage from over-heating. To prevent such dam-age, ºDº position should be
used in hill climbing or hardtowing.
(d) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector
lever to the ºRº position.
NOTICE
Never shift into reverse while the
vehicle is moving.
(e) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever fully to securely apply the parking brake.
3. With the brake pedal pressed down, shift the selector lever to
the ºPº position.

4RUNNER (1998)
SETTING AT A DESIRED SPEED
On vehicles with automatic transmis-
sion, the transmission must be in ºDº
before you set the cruise control
speed.
Bring your vehicle to the desired
speed, push the lever down in the
ºSET/COASTº direction and release it.
This sets the vehicle at that speed. If
the speed is not satisfactory, tap the
lever up for a faster speed, or tap it
down for a slower speed. Each tap
changes the set speed by 1.6 km/h
(1.0 mph). You can now take your foot
off the accelerator pedal. If you need accelerationÐfor example,
when passingÐdepress the accelera-
tor pedal enough for the vehicle to
exceed the set speed. When you re-
lease it, the vehicle will return to the
speed set prior to the acceleration.
CAUTION
For manual transmission:
While driving with the cruise con-
trol on, do not shift to neutral
without depressing the clutch
pedal, as this may cause engine
racing or overrevving.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by:a. Pulling the lever in the ºCANCELº
direction and releasing it.
b. Depressing the brake pedal.
c. Depressing the clutch pedal (manu- al transmission).
If the vehicle speed falls below about
40 km/h (25 mph), the preset speed
will automatically cancel out.
If the vehicle speed drops 16 km/h
(10 mph) below the preset speed, the
preset speed will also automatically
cancel out.

4RUNNER (1998)
To crank the engine without de-
pressing the clutch pedal, push the
switch with the ignition on.
The switch stays on as long as the
ignition is on. And it will automatically
turn off when the ignition is off.
This switch cancels the clutch start
system, which is desi gned to keep the
starter motor from operating if the
clutch pedal is not depressed all the
way down.
The switch allows the vehicle to be
driven out of difficult situations by
cranking the engine with the clutch engaged. Never use the switch for normal en-
gine starting. Be sure to follow the
starting procedure instructed in ºHow
to start the engineº in Part 3.
Clutch start cancel switch
(four- wheel drive models wi
manual transmission)

4RUNNER (1998)
Part 3
STARTING AND
DRIVING
Before starting the engine
How to start the engine
Tips for driving in various
conditions
Off- road driving precautions
Winter driving tips
Tr ailer towing
How to save fuel and make
your
vehicle last longer, too
Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, seat cushion angle, head re-
straint height and steering wheel
angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts. 1. Apply the parking brake firmly.
2. Turn off unnecessary lights and ac-
cessories.
3. Manual transmission: Press the
clutch pedal to the floor and shift
the transmission into neutral. Hold
the clutch pedal to the floor until
the engine is started. A starter
safety device will prevent the start-
er from operating if the clutch ped-
al is not fully depressed.
Automatic transmission: Put the
selector lever in ºPº. If you need to
restart the engine while the vehicle
is moving, put the selector lever in
ºNº. A starter safety device will pre-
vent the starter from operating if the
selector lever is in any drive position.
4. Automatic transmission only: De-
press the brake pedal and hold it
to the floor until driving off.
How to start the engineÐ
(a) Before cranking

4RUNNER (1998)
(b) Starting the engine
Before starting the engine, be sure to
follow the instructions in º(a) Before
crankingº.
Normal starting procedure
The multiport fuel injection system/se-
quential multiport fuel injection system
in your engine automatically controls
the proper air- fuel mixture for starting.
You can start a cold or hot engine as
follows:
1. With your foot off the accelerator
pedal, crank the engine by turning the
key to ºSTARTº. Release it when the
engine starts.
2. After the engine runs for about 10
seconds, you are ready to drive.
If the weather is below freezing, let
the engine warm up for a few minutes
before driving.
If the engine stalls...
Simply restart it, using the correct
procedure given in normal starting.
If the engine will not startÐ
See ºIf your vehicle will not startº in
Part 4.
NOTICE
Do not crank for more than 30 seconds at a time. This mayoverheat the starter and wiringsystems.
Do not race a cold engine.
If the engine becomes difficult
to start or stalls frequently,have the engine checked im-mediately.
Always slow down in gusty cross-
winds. This will allow you much
better control.
Drive slowly onto curbs and, if
possible, at a right angle. Avoid
driving onto high, sharp- edged ob-
jects and other road hazards. Fail-
ure to do so can lead to severe
tire damage resulting in tire bursts.
When parking on a hill, turn the
front wheels until they touch the
curb so that the vehicle will not
roll. Apply the parking brake, and
place the transmission in ºPº (auto-
matic) or in first or reverse (manu-
al). If necessary, block the wheels.
Washing your vehicle or driving
through deep water may get the
brakes wet. To see whether they
are wet, check that there is no
traffic near you, and then press the
pedal lightly. If you do not feel a
normal braking force, the brakes
are probably wet. To dry them,
drive the vehicle cautiously while
lightly pressing the brake pedal
with the parking brake pulled. If
they still do not work safely, pull to
the side of the road and call a
Toyota dealer for assistance.
Tips for driving in various
conditions

4RUNNER (1998)
Use a washer fluid containing an
antifreeze solution.
This product is available at your Toyo-
ta dealer and most auto parts stores.
Follow the manufacturer 's directions
for how much to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because itmay damage your vehicle's paint.
Do not use your parking brake
when there is a possibility it could
freeze.
When parking, put the transmission
into ºPº (automatic) or into first or
reverse (manual) and block the rear
wheels. Do not use the parking brake,
or snow or water accumulated in and
around the parking brake mechanism
may freeze, making it hard to release.
Keep ice and snow from accumulat-
ing under the fenders.
Ice and snow built up under your
fenders can make steering difficult.
During bad winter driving, stop and
check under the fenders occasionally. Depending on where you are driv-
ing, we recommend you carry some
emergency equipment.
Some of the things you might put in
the vehicle are tire chains, window
scraper, bag of sand or salt, flares,
small shovel, jumper cables, etc.
Trailer towing
Your vehicle is designed primarily as
a passenger- and- load- carrying ve-
hicle. Towing a trailer will have an
adverse effect on handling, perfor-
mance, braking, durability and driving
economy (fuel consumption, etc.).
Your safety and satisfaction depend
on the proper use of correct equip-
ment and cautious driving habits. For
your safety and the safety of others,
you must not overload your vehicle or
trailer. Ask your local Toyota dealer
for further details before towing.
WEIGHT LIMITS
Before towing, make sure the total
trailer weight, gross combination
weight, gross vehicle weight, gross
axle weight and trailer tongue load
are all within the limits.
The total trailer weight and tongue
load can be measured with platform
scales found at a highway weighing
station, building supply company,
trucking company, junk yard, etc.

4RUNNER (1998)
TRAILER TOWING TIPS
When towing a trailer, your vehicle
will handle differently than when
not towing. The three main causes
of vehicle- trailer accidents are driv-
er error, excessive speed and im-
proper trailer loading. Keep these in
mind when towing:
Before starting out, check operation
of the lights and all vehicle- trailer
connections. After driving a short
distance, stop and recheck the
lights and connections. Before ac-
tually towing a trailer, practice turn-
ing, stopping and backing with a
trailer in an area away from traffic
until you learn the feel.
Backing with a trailer is difficult
and requires practice. Grip the bot-
tom of the steering wheel and
move your hand to the left to move
the trailer to the left. Move your
hand to the right to move the trail-
er to the right. (This procedure is
generally opposite to that when
backing without a trailer). Also, just
turn the steering wheel a little at
a time, avoiding sharp or prolonged
turning. Have someone guide you
when backing to reduce the risk of
an accident.
Because stopping distance may be
increased, vehicle- to- vehicle dis-
tance should be increased when
towing a trailer. For each 16 km/h
(10 mph) of speed, allow at least
one vehicle and trailer length bet-
ween you and the vehicle ahead.
Avoid sudden braking as you may
skid, resulting in jackknifing and
loss of control. This is especially
true on wet or slippery surfaces.
Avoid jerky starts or sudden accel-
eration. If your vehicle has a
manual transmission, prevent ex-
cessive clutch slippage by keeping
engine rpm low and not racing the
engine. Always start out in first
gear.
Avoid jerky steering and sharp
turns. The trailer could hit your ve-
hicle in a tight turn. Slow down
before making a turn to avoid the
necessity of sudden braking.
Remember that when making a
turn, the trailer wheels will be clos-
er than the vehicle wheels to the
inside of the turn. Therefore, com-
pensate for this by making a larger
than normal turning radius with y-
our vehicle.
Crosswinds and rough roads will
adversely affect handling of your
vehicle and trailer, causing sway.
Pay attention to the rear from time
to time to prepare yourself for be-
ing passed by large trucks or
buses, which may cause your ve-
hicle and trailer to sway. If swaying
happens, firmly grip the steering
wheel and reduce speed immedi-
ately but gradually. Never increase
speed. Steer straight ahead. If you
make no extreme correction with
the steering or brakes, the vehicle
and trailer will stabilize.
Be careful when passing other ve-
hicles. Passing requires consider-
able distance. After passing a ve-
hicle, do not forget the length of
your trailer and be sure you have
plenty of room before changing
lanes.
In order to maintain engine braking
efficiency, do not use fifth gear
(manual transmission) or overdrive
(automatic transmission).

4RUNNER (1998)
Because of the added load of the
trailer, your vehicle's engine may
overheat on hot days (at tempera-
tures over 30 C [85 F]) when go-
ing up a long or steep grade with
a trailer. If the engine coolant tem-
perature gauge indicates overheat-
ing, immediately turn off the air-
conditioning (if in use), pull off the
road and stop in a safe spot. Refer
to ºIf your vehicle overheatsº in
Part 4 of this manual.
Always place wheel blocks under
both the vehicle and trailer wheels
when parking. Apply the parking
brake firmly. Put the transmission
in Pº (automatic) or in first or re-
verse (manual). Avoid parking on a
slope with a trailer, but if it cannot
be avoided, do so only after per-
forming the following:
1. Apply the brakes and hold.
2. Have someone place wheel blocks under both the vehicle and trailer
wheels.
3. When the wheel blocks are in place, release your brakes slowly
until the blocks absorb the load.
4. Apply the parking brake firmly. 5. Shift into first or reverse (manual)
or ºPº (automatic) and turn off the
engine. When restarting out after parking on
a slope:
1. With the transmission in ºPº posi- tion (automatic) or the clutch pedal
depressed (manual), start the en-
gine. (With an automatic transmis-
sion, be sure to keep the brake
pedal depressed.)
2. Shift into gear.
3. Release the parking brake (also foot brake on automatic transmis-
sion vehicles) and slowly pull or
back away from the wheel blo cks.
Stop and apply your brakes.
4. Have someone retrieve the blo cks.
CAUTION
Do not exceed 72 km/h (45
mph) or the posted towing
speed limit, whichever is lower.
Because instab ility (swaying) of
a towing vehicle- trailer com-
bination usually increases as
the speed increases, exceeding
72 km/h (45 mph) may cause
loss of control.