automatic transmission TOYOTA 4RUNNER 1998 Owner's Manual

4RUNNER (1998)
Part 4
IN CASE OF AN
EMERGENCY
If your vehicle will not start
If your engine stalls while
driving
If your vehicle overheats
If you have a flat tire
If your vehicle needs to be
towed
If you cannot shift automatic
transmission selector lever
If you lose your keys
Before making these checks, make
sure you have followed the correct
starting procedure given in ºHow to
start the engineº in Part 3 and that
you have sufficient fuel.
If the engine is not turning over or
is turning over too slowlyÐ
1. Check that the battery terminals are tight and clean.
2. If the battery terminals are O.K., switch on the interior light.
3. If the light is out, dim or goes out when the starter is cranked, the
battery is discharged. You may try
jump starting. See º(c) Jump start-
ingº for further instructions.
If the light is O.K., but the engine still
will not start, it needs adjustment or
repair. Call a Toyota dealer or quali-
fied repair shop.
NOTICE
Do not pull- or push- start the ve- hicle. It may damage the vehicleor cause a collision when the en-
gine starts. Also the three- way
catalytic converter may overheatand become a fire hazard.
If the engine turns over at its nor-
mal speed but will not startÐ
1. Check that all the push- on connec- tors are tight. (For example, con-
nections at the spark plugs, ignition
coil and/or distributor)
2. If the connectors are O.K., the en- gine may be flooded because of
repeated cranking. See º(b) Start-
ing a flooded engineº for further
instructions.
If your vehicle will not start
Ð
(a) Simple checks

4RUNNER (1998)
CAUTION
When making the connections, to
avoid serious injury, do not lean
over the battery or accidentally
let the jumper cables or clamps
touch anything except the correct
battery terminals or the ground.
5. Start your engine in the normal
way. After starting, run it at about
2000 rpm for several minutes with
the accelerator pedal lightly de-
pressed.
6. Carefully disconnect the cables in the exact reverse order: the nega-
tive cable and then the positive
cable.
7. Carefully dispose of the battery cover clothsÐthey may now con-
tain sulfuric acid.
8. If removed, replace all the battery vent plugs.
If the cause of your battery discharg-
ing is not apparent (for example,
lights left on), you should have it
checked. If your engine stalls while driving...
1. Reduce your speed gradually, keep- ing a straight line. Move cautiously
off the road to a safe place.
2. Turn on your emergency flashers.
3. Try starting the engine again.
If the engine will not start, see ºIf
your vehicle will not startº.
CAUTION
If the engine is not running, the
power assist for the brakes and
steering will not work so steering
and braking will be much harder
than usual.
If your vehicle overheats
If your engine coolant temperature
gauge indicates overheating, if you
experience a loss of power, or if
you hear a loud knocking or ping-
ing noise, the engine has probably
overheated. You should follow this
procedure... 1. Pull safely off the road, stop the vehicle and turn on your emergen-
cy flashers. Put the transmission in
ºPº (automatic) or neutral (manual)
and apply the parking brake. Turn
off the air conditioning if it is being
used.
2. If coolant or steam is boiling out of the radiator or reservoir, stop the
engine. Wait until the steam sub-
sides before opening the hood. If
there is no coolant boiling over or
steam, leave the engine running.
CAUTION
To help avoid personal injury,
keep the hood closed until there
is no steam. Escaping steam or
coolant is a sign of very high
pressure.
If your engine stalls while
driving

4RUNNER (1998)
Stop the vehicle on a level firm
ground, firmly set the parking
brake and put the transmission
in ºPº (automatic) or reverse
(manual). Block the wheel diag-
onally opposite to the one be-
ing changed if necessary.
Make sure to set the jack prop-
erly in the jack point. Raising
the vehicle with jack improperly
positioned will damage the ve-
hicle or may allow the vehicle
to fall off the jack and cause
personal injury.
Never get under the vehicle
when the vehicle is supported
by the jack alone.
Use the jack only for lifting
your vehicle during wheel
changing.
Do not raise the vehicle with
someone in the vehicle.
When raising the vehicle, do
not put an object on or under
the jack.
Raise the vehicle only high
enough to remove and change
the tire.NOTICE
Do not continue driving with a
deflated tire. Driving even a shortdistance can damage a tire be-yond repair.
ÐRequired tools and spare
tire

4RUNNER (1998)
Only when you cannot receive a
towing service from a Toyota dealer
or commercial tow truck service,
tow your vehicle carefully in accor-
dance with the instructions given in
ºÐEmergency towingº in this Part.
Proper equipment will help ensure that
your vehicle is not damaged while be-
ing towed. Commercial operators are
generally aware of the state/provincial
and local laws pertaining to towing.
Your vehicle can be damaged if it is
towed incorrectly. Although most oper-
ators know the correct procedure, it is
possible to make a mistake. To avoid
damage to your vehicle, make sure
the following few precautions are ob-
served. If necessary, show this page
to the tow truck driver. TOWING PRECAUTIONS:
Use a safety chain system for all tow-
ing, and abide by the state/provincial
and local laws. The wheels and axle
on the ground must be in good condi-
tion. If they are damaged, use a tow-
ing dolly.
Two- wheel drive modelsÐ
(a) Towing with wheel lift type
truck
From frontÐ Manual transmission:
We recommend using a towing dolly
under the rear wheels. If you do not
use a towing dolly, release the park-
ing brake and put the transmission
in neutral.
Automatic transmission:
Use a towing dolly under the rear
wheels.
NOTICE
Never tow a vehicle with an auto-
matic transmission from the frontwith the rear wheels on theground, as this may cause serious
damage to the transmission.
From rearÐ Place the ignition key in
the ºACCº position.
NOTICE
When lifting wheels, take care
to ensure adequate groundclearance for towing at the op-posite end of the raised vehicle.
Otherwise, the bumper and/orunderbody of the towed vehiclewill be damaged during towing.
Do not tow with the key re-moved or in the ºLOCKº posi-tion, as the steering lock mech-
anism is not strong enough tohold the front wheels straight
while towing.
(b) Using flat bed truck

4RUNNER (1998)
Four-wheel drive modelsÐ
(a) Towing with wheel lift type truck From frontÐ
Manual transmission:
We recommend using a towing dol-
ly under the rear wheels. If you do
not use a towing dolly, release the
parking brake, put the transmission
in neutral and the transfer in ºH2º.
Automatic transmission:
Use a towing dolly under the rear
wheels.
NOTICE
Never tow a vehicle with an auto-
matic transmission from the frontwith the rear wheels on the
ground, as this may cause serious
damage to the transmission.
From rearÐ We recommend using a
towing dolly under the front wheels. If
you do not use a towing dolly, place
the ignition key in the ºACCº position,
put the transmission in neutral and the
transfer in ºH2º.
NOTICE
Do not tow with the key removed
or in the ºLOCKº position whentowing from the rear without atowing dolly. The steering lock
mechanism is not strong enoughto hold the front wheels straight.
(b) Using flat bed truck

4RUNNER (1998)
If towing is necessary, we recom-
mend you to have it done by your
Toyota dealer or a commercial tow
truck service.
If towing service is not available in
an emergency, your vehicle may be
temporarily towed by a cable or
chain secured to the emergency
towing hook. Use extreme caution
when towing vehicles.
A driver must be in the vehicle to
steer it and operate the brakes.
Towing in this manner may be done
only on hard- surfaced roads for a
short distance and at low speeds.
Also, the wheels, axles, drive train,
steering and brakes must all be in
good condition.
CAUTION
Use extreme caution when towing
vehicles. Avoid sudden starts or
erratic driving maneuvers which
would place excessive stress on
the emergency towing hook and
towing cable or chain. The hook
and towing cable or chain may
break and cause serious injury or damage.
NOTICE
Use only a cable or chain specifi-
cally intended for use in towingvehicles. Securely fasten the cableor chain to the towing hook pro-
vided.
Before towing, release the parking
brake and put the transmission in neu-
tral (manual) or ºNº (automatic) and
the transfer in ºH2º (four- wheel drive
models). The key must be in ºACCº
(engine off) or ºONº (engine running).

4RUNNER (1998)
Automatic transmission ºParkº mech- anism
Check the lock release button of the
selector lever for proper and smooth
operation. On a safe incline, check
that your vehicle is held securely with
the selector lever in ºPº position and
all brakes released.
IN THE ENGINE COMPARTMENT
Items listed below should be
checked from time to time, e.g.
each time when refueling.
Washer fluid
Make sure there is sufficient fluid in
the tank. See Chapter 7- 3 for addi-
tional information.
Engine coolant level
Make sure the coolant level is be-
tween the ºFULLº and ºLOWº lines on
the see- through reservoir when the
engine is cold. See Chapter 7- 2 for
additional information.
Battery electrolyte level
Make sure the electrolyte level of all
battery cells is between upper and
lower level lines on the case. Add
only distilled water when replenishing.
See Chapter 7- 3 for additional in-
formation. Brake fluid level
Make sure the brake fluid level is cor-
rect. See Chapter 7- 2 for additional
information.
Engine oil level
Check the level on the dipstick with
the engine turned off and the vehicle
parked on a level spot. See Chapter
7- 2 for additional information.
Power steering fluid level
Check the level through the reservoir.
The level should be in the ºHOTº or
ºCOLDº range depending on the fluid
temperature. See Chapter 7- 2 for
additional information.
Exhaust system
If you notice any change in the sound
of the exhaust or smell exhaust
fumes, have the cause located and
corrected immediately. (See engine ex-
haust cautions in Part 2.)
Be on the alert for changes in perfor-
mance, sounds, and visual tip- offs
that indicate service is needed. Some
important clues are as follows:
Engine missing, stumbling, or ping-
ing
Appreciable loss of power
Strange engine noises
A leak under the vehicle (however,
water dripping from the air condi-
tioning after use is normal.)
Change in exhaust sound (This
may indicate a dangerous carbon
monoxide leak. Drive with the win-
dows open and have the exhaust
system checked immediately.)
Flat- looking tire; excessive tire
squeal when cornering; uneven tire wear
Vehicle pulls to one side when
driving straight on a level road
Strange noises related to suspen-
sion movement
Loss of brake effectiveness;
spongy feeling brake or clutch ped-
al; pedal almost touches floor; ve-
hicle pulls to one side when brak-
ing
Engine coolant temperature continu-
ally higher than normal
Does your vehicle need
repairing?

4RUNNER (1998)
Parts and tools
Here is a list of parts and tools you
will need on performing do- it- yourself
maintenance. Remember all Toyota
parts are designed in metric sizes, so
your tools must be metric.
Checking the engine oil level
Parts (if level is low): Engine oil API grade SH, ºEnergy-
Conserving IIº or SJ, ºEnergy-
Conservingº multigrade or ILSAC
multigrade having viscosity proper
for your climate
Tools: Rag or paper towel
Funnel (only for adding oil)
Checking the engine coolant level
Parts (if level is low): Ethylene- glycol antifreeze
Demineralized or distilled water
Tools: Funnel (only for adding coolant)
Checking brake fluid
Parts (if level is low): SAE J1703 or FMVSS No. 116
DOT 3 brake fluid
Tools: Rag or paper towel
Funnel (only for adding fluid) Checking power steering fluid
Parts (if level is low):
Automatic transmission fluid DEXRON II or III
Tools: Rag or paper towel
Funnel (only for adding fluid)
Checking battery condition
Tools: Warm water
Baking soda
Grease
Conventional wrench (for terminal
clamp bolts)
Checking and replacing fuses
Parts (if replacement is necessary): Fuse with same amperage rating
as original
Tools: Conventional wrench (for instrument
lower panel nut)
Adding washer fluid
Parts: Water
Washer fluid containing antifreeze
(for winter use)
Tools: Funnel Replacing light bulbs
Parts:
Bulb with same number and watt-
age rating as original (See charts
in ºReplacing light bulbsº in Chap-
ter 7- 3.)
Tools: Screwdriver

4RUNNER (1998)
Checking power steering
fluid
If cold add
If cold O.K.
If hot add If hot O.K.
Check the fluid level on the dip-
stick. If necessary, add automatic
transmission fluid DEXRON II or III.
If the vehicle has been driven around
80 km/h (50 mph) for 20 minutes (a
little more in frigid temperatures), the
fluid is hot (60 CÐ80 C or
140 FÐ175 F). You may also check
the level when the fluid is cold (about
room temperature, 10 CÐ30 C or
50 FÐ85 F) if the engine has not
been run for about five hours.
a. Clean all dirt from outside of the
reservoir tank.
b. Remove the filler cap by turning it
counterclockwise and wipe the dipstick
clean. c. Reinstall the filler cap.
d. Remove the filler cap again and
look at the fluid level. If the fluid is
cold, the level should be in the
ºCOLDº range on the dipstick.
Similarly, if it is hot, the fluid level
should be in the ºHOTº range. If the
level is at the low side of either
range, add automatic transmission
fluid DEXRON
II or III to bring the
level within the range.
e. After replacing the filler cap, visual-
ly check the steering box case, vane
pump and hose connections for leaks
or damage.
CAUTION
The reservoir tank may be hot so
be careful not to burn yourself.
NOTICE
Avoid overfilling, or the power
steering could be damaged.

4RUNNER (1998)
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.):
3RZ- FE engineWith rear heater 11.0 (11.6, 9.7)
Without rear heater
10.0 (10.6, 8.8)
5VZ- FE engine With rear heater
9.0 (9.5, 7.9)
Without rear heater
8.0 (8.5, 7.0) Coolant type:
With ethylene- glycol antifreeze
(Do not use alcohol type.)
BATTERY
Open voltage *
at 20 C (68 F):
12.6Ð12.8 V Fully charged
12.2Ð12.4 V Half charged
11.8 Ð12.0 V Discharged
* : Voltage that is checked 20 minutes
after
the key is removed with all the lights
turned off
Charging rates:
5 A max.
CLUTCH
Pedal freeplay, mm (in.): 5Ð15 (0.2Ð0.6)
Fluid type: SAE J1703 or FMVSS No. 116 DOT
3 MANUAL TRANSMISSION
Oil capacity, L (qt., Imp. qt.):
3RZ- FE engine
Two- wheel drive models 2.6 (2.7, 2.3)
Four- wheel drive models
2.5 (2.6, 2.2)
5VZ- FE engine 2.2 (2.3, 1.9)
Oil type: Gear oil API GL- 4 or GL- 5
Recommended oil viscosity: SAE 75W- 90
AUTOMATIC TRANSMISSION
Fluid capacity (drain and ref ill),
L (qt., Imp. qt.): Two- wheel drive models Up to 1.6 (1.7, 1.4)
Four- wheel drive models Up to 2.0 (2.1, 1.8)