towing TOYOTA 4RUNNER 1998 User Guide

4RUNNER (1998)
Good driving practice
If it is difficult to shift into reverse,
put the transmission in neutral, re-
lease the clutch pedal momentarily,
and then try again.
When towing a trailer, in order to
maintain engine braking efficiency,
do not use the fifth gear.
CAUTION
Be careful when downshifting on
a slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
NOTICE
Make sure the vehicle is com-
pletely stopped before shiftinginto reverse.
Four- wheel drive systemÐ
(a) Front drive control (lev
type)

4RUNNER (1998)
The brake pad wear limit indicators
on your disc brakes give a warning
noise when the brake pads are
worn to where replacement is re-
quired.
If you hear a squealing or scraping
noise while driving, have the brake
pads checked and replaced by your
Toyota dealer as soon as possible.
Expensive rotor damage can result if
the pads are not replaced when nec-
essary. Luggage stowage pr
ecau-
tions
When stowing luggage or cargo in the
vehicle, observe the following:
Put luggage or cargo in the lug-
gage compartment when at all pos-
sible. Be sure all items are se-
cured in place.
Be careful to keep the vehicle bal-
anced. Locating the weight as far
forward as possible helps maintain
balance.
For better fuel economy, do not
carry unneeded weight.
CAUTION
To prevent luggage or packages
from sliding forward during
braking, do not stack anything
in the luggage compartment
higher than the seatbacks. Keep
luggage or packages low, as
close to the floor as possible.
Never allow anyone to ride in
the luggage compartment. It is
not designed for passengers.
They should ride in their seats
with their seat belts properly
fastened. Otherwise, they are
much more likely to suffer seri-
ous bodily injury, in the event
of sudden braking or a colli-
sion.

4RUNNER (1998)
Part 3
STARTING AND
DRIVING
Before starting the engine
How to start the engine
Tips for driving in various
conditions
Off- road driving precautions
Winter driving tips
Tr ailer towing
How to save fuel and make
your
vehicle last longer, too
Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, seat cushion angle, head re-
straint height and steering wheel
angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts. 1. Apply the parking brake firmly.
2. Turn off unnecessary lights and ac-
cessories.
3. Manual transmission: Press the
clutch pedal to the floor and shift
the transmission into neutral. Hold
the clutch pedal to the floor until
the engine is started. A starter
safety device will prevent the start-
er from operating if the clutch ped-
al is not fully depressed.
Automatic transmission: Put the
selector lever in ºPº. If you need to
restart the engine while the vehicle
is moving, put the selector lever in
ºNº. A starter safety device will pre-
vent the starter from operating if the
selector lever is in any drive position.
4. Automatic transmission only: De-
press the brake pedal and hold it
to the floor until driving off.
How to start the engineÐ
(a) Before cranking

4RUNNER (1998)
Use a washer fluid containing an
antifreeze solution.
This product is available at your Toyo-
ta dealer and most auto parts stores.
Follow the manufacturer 's directions
for how much to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because itmay damage your vehicle's paint.
Do not use your parking brake
when there is a possibility it could
freeze.
When parking, put the transmission
into ºPº (automatic) or into first or
reverse (manual) and block the rear
wheels. Do not use the parking brake,
or snow or water accumulated in and
around the parking brake mechanism
may freeze, making it hard to release.
Keep ice and snow from accumulat-
ing under the fenders.
Ice and snow built up under your
fenders can make steering difficult.
During bad winter driving, stop and
check under the fenders occasionally. Depending on where you are driv-
ing, we recommend you carry some
emergency equipment.
Some of the things you might put in
the vehicle are tire chains, window
scraper, bag of sand or salt, flares,
small shovel, jumper cables, etc.
Trailer towing
Your vehicle is designed primarily as
a passenger- and- load- carrying ve-
hicle. Towing a trailer will have an
adverse effect on handling, perfor-
mance, braking, durability and driving
economy (fuel consumption, etc.).
Your safety and satisfaction depend
on the proper use of correct equip-
ment and cautious driving habits. For
your safety and the safety of others,
you must not overload your vehicle or
trailer. Ask your local Toyota dealer
for further details before towing.
WEIGHT LIMITS
Before towing, make sure the total
trailer weight, gross combination
weight, gross vehicle weight, gross
axle weight and trailer tongue load
are all within the limits.
The total trailer weight and tongue
load can be measured with platform
scales found at a highway weighing
station, building supply company,
trucking company, junk yard, etc.

4RUNNER (1998)
CAUTION
The total trailer weight (trailer
weight plus its cargo load)
must not exceed the following.
Exceeding this weight is dan-
gerous. If towing a trailer over
907 kg (2000 lb.), it is neces-
sary to use a sway control de-
vice with a sufficient capacity.
3RZ- FE engine 1587 kg (3500 lb.)
5VZ- FE engine 2267 kg (5000 lb.)
The gross combination weight
(sum of your vehicle weight
plus its load and the total trail-
er weight) must not exceed the
following.
Two- wheel drive models 3RZ- FE engine3447 kg (7600 lb.)
5VZ- FE engine 3992 kg (8800 lb.)
Four- wheel drive models 3RZ- FE engine3583 kg (7900 lb.)
5VZ- FE engine 4173 kg (9200 lb.)

4RUNNER (1998)
Total trailer weight
Tongue load
Tongue load
Total trailer weight
100 9 to 11 %
The trailer cargo load should be
distributed so that the tongue
load is 9 to 11% of the total
trailer weight, not exceeding the
maximum of the following. Nev-
er load the trailer with more
weight in the back than in the
front. About 60% of the trailer
load should be in the front half
of the trailer and the remaining
40% in the rear.
3RZ- FE engine158 kg (350 lb.)
5VZ- FE engine 226 kg (500 lb.)HITCHES
Use only a weight carrying hitch
designed for the total trailer weight.
Toyota does not recommend using
a weight distribution (load equaliz-
ing) hitch.
The hitch must be bolted securely
to the vehicle frame and installed
according to the hitch manufactur-
er 's instructions.
The hitch ball and king pin should
have a light coat of grease.
Toyota recommends removing the
hitch when not towing to preventin-
jury and/or damage due to the
hitch in event of a rear end colli-
sion. After removal of the hitch,
seal the installation area to prevent
entry of exhaust fumes and mud.
NOTICE
Do not use an axle- mounting
hitch as it may cause damage tothe axle housing, wheel bearings,wheels and or tires.
BRAKES AND SAFETY CHAINS
Toyota recommends trailers with
brakes that conform to any appli-
cable federal and state/provincial
regulations.

4RUNNER (1998)
A safety chain must always be
used between the towing vehicle
and the trailer. Leave sufficient
slack in the chain for turns. The
chain should cross under the
trailer tongue to prevent the
tongue from dropping to the
ground in case it becomes dam-
aged or separated. For correct
safety chain procedures, follow
the hitch or trailer manufactur-
er 's recommendations.
CAUTION
If the total trailer weight ex-
ceeds 453 kg (1000 lb.), trailer
brakes are required .
Never tap into your vehicle's
hydraulic system as it would
lower its braking effectiveness .
Never tow a trailer without us-
ing a safety chain securely atta-
ched to both the trailer and the
vehicle. If damage occurs to the
coupling unit or hitch ball,
there is danger of the trailer
wandering over into another
lane.
TIRES
Ensure that your vehicle's tires are
properly inflated. See Chapter 7- 2
for instructions.
The trailer tires should be inflated
to the pressure recommended by
the trailer manufacturer in respect
to the total trailer weight.
TRAILER LIGHTS Trailer lights must comply with fed-
eral, state/provincial and local re-
gulations. See your local recre-
ational vehicle dealer or rental
agency for the correct type of wir-
ing and relays for your trailer.
Check for correct operation of the
turn signals and stop lights each
time you hitch up. Direct splicing
may damage your vehicle's electri-
cal system and cause a malfunc-
tion of your lights.
BREAK- IN SCHEDULE Toyota recommends that you do
not tow a trailer with a new vehicle
or a vehicle with any new power
train component (engine, transmis-
sion, differential, wheel bearing,
etc.) for the first 800 km (500
miles) of driving. MAINTENANCE
If you tow a trailer, your vehicle
will require more frequent
maintenance due to the additional
load. For this information, please
refer to the scheduled maintenance
information in the ºOwner 's Manual
Supplement/Maintenance Scheduleº.
Retighten all fixing bolts of the
towing ball and bracket after
approximately 1000 km (600 miles)
of trailer driving.
PRE- TOWING SAFETY CHECK
Check that your vehicle remains
level when a loaded or unloaded
trailer is hitched. Do not drive if
the vehicle has an abnormal nose-
up or nose- down condition, and
check for improper tongue load,
overload, worn suspension or other
possible causes.
Make sure the trailer cargo is se-
curely loaded so that it cannot
shift.
Check that your rear view mirrors
conform to any applicable federal,
state/provincial or local regulation.
If not, install the rear view mirrors
required for towing purpose.

4RUNNER (1998)
TRAILER TOWING TIPS
When towing a trailer, your vehicle
will handle differently than when
not towing. The three main causes
of vehicle- trailer accidents are driv-
er error, excessive speed and im-
proper trailer loading. Keep these in
mind when towing:
Before starting out, check operation
of the lights and all vehicle- trailer
connections. After driving a short
distance, stop and recheck the
lights and connections. Before ac-
tually towing a trailer, practice turn-
ing, stopping and backing with a
trailer in an area away from traffic
until you learn the feel.
Backing with a trailer is difficult
and requires practice. Grip the bot-
tom of the steering wheel and
move your hand to the left to move
the trailer to the left. Move your
hand to the right to move the trail-
er to the right. (This procedure is
generally opposite to that when
backing without a trailer). Also, just
turn the steering wheel a little at
a time, avoiding sharp or prolonged
turning. Have someone guide you
when backing to reduce the risk of
an accident.
Because stopping distance may be
increased, vehicle- to- vehicle dis-
tance should be increased when
towing a trailer. For each 16 km/h
(10 mph) of speed, allow at least
one vehicle and trailer length bet-
ween you and the vehicle ahead.
Avoid sudden braking as you may
skid, resulting in jackknifing and
loss of control. This is especially
true on wet or slippery surfaces.
Avoid jerky starts or sudden accel-
eration. If your vehicle has a
manual transmission, prevent ex-
cessive clutch slippage by keeping
engine rpm low and not racing the
engine. Always start out in first
gear.
Avoid jerky steering and sharp
turns. The trailer could hit your ve-
hicle in a tight turn. Slow down
before making a turn to avoid the
necessity of sudden braking.
Remember that when making a
turn, the trailer wheels will be clos-
er than the vehicle wheels to the
inside of the turn. Therefore, com-
pensate for this by making a larger
than normal turning radius with y-
our vehicle.
Crosswinds and rough roads will
adversely affect handling of your
vehicle and trailer, causing sway.
Pay attention to the rear from time
to time to prepare yourself for be-
ing passed by large trucks or
buses, which may cause your ve-
hicle and trailer to sway. If swaying
happens, firmly grip the steering
wheel and reduce speed immedi-
ately but gradually. Never increase
speed. Steer straight ahead. If you
make no extreme correction with
the steering or brakes, the vehicle
and trailer will stabilize.
Be careful when passing other ve-
hicles. Passing requires consider-
able distance. After passing a ve-
hicle, do not forget the length of
your trailer and be sure you have
plenty of room before changing
lanes.
In order to maintain engine braking
efficiency, do not use fifth gear
(manual transmission) or overdrive
(automatic transmission).

4RUNNER (1998)
Because of the added load of the
trailer, your vehicle's engine may
overheat on hot days (at tempera-
tures over 30 C [85 F]) when go-
ing up a long or steep grade with
a trailer. If the engine coolant tem-
perature gauge indicates overheat-
ing, immediately turn off the air-
conditioning (if in use), pull off the
road and stop in a safe spot. Refer
to ºIf your vehicle overheatsº in
Part 4 of this manual.
Always place wheel blocks under
both the vehicle and trailer wheels
when parking. Apply the parking
brake firmly. Put the transmission
in Pº (automatic) or in first or re-
verse (manual). Avoid parking on a
slope with a trailer, but if it cannot
be avoided, do so only after per-
forming the following:
1. Apply the brakes and hold.
2. Have someone place wheel blocks under both the vehicle and trailer
wheels.
3. When the wheel blocks are in place, release your brakes slowly
until the blocks absorb the load.
4. Apply the parking brake firmly. 5. Shift into first or reverse (manual)
or ºPº (automatic) and turn off the
engine. When restarting out after parking on
a slope:
1. With the transmission in ºPº posi- tion (automatic) or the clutch pedal
depressed (manual), start the en-
gine. (With an automatic transmis-
sion, be sure to keep the brake
pedal depressed.)
2. Shift into gear.
3. Release the parking brake (also foot brake on automatic transmis-
sion vehicles) and slowly pull or
back away from the wheel blo cks.
Stop and apply your brakes.
4. Have someone retrieve the blo cks.
CAUTION
Do not exceed 72 km/h (45
mph) or the posted towing
speed limit, whichever is lower.
Because instab ility (swaying) of
a towing vehicle- trailer com-
bination usually increases as
the speed increases, exceeding
72 km/h (45 mph) may cause
loss of control.

4RUNNER (1998)
(b) Starting a flooded engine
If the engine will not start, your
engine may be flooded because of
repeated cranking.
If this happens, turn the key to
ºSTARTº with the accelerator pedal
held down. Keep the key and acceler-
ator pedal so for 15 seconds and re-
lease them. Then try starting the en-
gine with your foot off the accelerator
pedal.
If the engine does not start after 15
seconds of cranking, release the key,
wait a few minutes and try again.
If the engine still will not start, it
needs adjustment or repair. Call a
Toyota dealer or qualified repair shop
for assistance.
NOTICE
Do not crank for more than 30 seconds at a time. This may over-heat the starter and wiring sys-tems.
(c) Jump starting
To avoid serious personal injury
and damage to your vehicle which
might result from battery explosion,
acid burns, electrical burns, or dam-
aged electronic components, these
instructions must be followed pre-
cisely.
If you are unsure about how to follow
this procedure, we strongly recom-
mend that you seek the help of a
competent mechanic or towing service.
CAUTION
Batteries contain sulfuric acid
which is poisonous and corro-
sive. Wear protective safety
glasses when jump starting, and
avoid spilling acid on your skin, clothing, or vehicle.
If you should accidentally get
acid on yourself or in your
eyes, remove any contaminated
clothing and flush the affected
area with water immediately.
Then get immediate medical
attention. If possible, continue
to apply water with a sponge or
cloth while en route to the med-
ical office.
The gas normally produced by
a battery will explode if a flame
or spark is brought near. Use
only standardized jumper cables
and do not smoke or light a
match while jump starting.
NOTICE
The battery used for boosting
must be 12 V. Do not jump startunless you are sure that thebooster battery is correct.