TOYOTA 4RUNNER 1998 Owners Manual

4RUNNER (1998)
3. Visually check to see if the engine drive belt (fan belt) is broken or
loose. Look for obvious coolant
leaks from the radiator, hoses, and
under the vehicle. However, note
that water draining from the air
conditioning is normal if it has
been used.
CAUTION
When the engine is running, keep
hands and clothing away from the
moving fan and engine drive
belts.
4. If the engine drive belt is brokenor the coolant is leaking, stop the
engine immediately. Call a Toyota
dealer for assistance.
5. If the engine drive belt is O.K. and there are no obvious leaks, you
may help the engine cool down
more quickly by running it at about
1500 rpm for a few minutes with
the accelerator pedal lightly de-
pressed.
6. Check the coolant reservoir. If it is dry, add coolant to the reservoir
while the engine is running. Fill it
about half full.
CAUTION
Do not attempt to remove the ra-
diator cap when the engine and
radiator are hot. Serious injury
could result from scalding hot
fluid and steam blown out under
pressure.
7. After the engine coolant tempera-ture has cooled to normal, again
check the coolant level in the res-
ervoir. If necessary, bring it up to
half full again. Serious coolant loss
indicates a leak in the system. You
should have it checked as soon as
possible at your Toyota dealer. If you have a flat tireÐ
1. Reduce your speed gradually, keep- ing a straight line. Move cautiously
off the road to a safe place well
away from the traffic. Avoid stop-
ping on the center divider of a
highway. Park on a level spot with
firm ground.
2. Stop the engine and turn on your emergency flashers.
3. Firmly set the parking brake and put the transmission in ºPº (auto-
matic) or reverse (manual).
4. Have everyone get out of the ve- hicle on the side away from traffic.
5. Read the following instructions thoroughly.
CAUTION
When jacking, be sure to observe
the following to reduce the possi-
bility of personal injury: Follow jacking instructions.
Do not start or run the engine
while your vehicle is supported
by the jack.

4RUNNER (1998)
Stop the vehicle on a level firm
ground, firmly set the parking
brake and put the transmission
in ºPº (automatic) or reverse
(manual). Block the wheel diag-
onally opposite to the one be-
ing changed if necessary.
Make sure to set the jack prop-
erly in the jack point. Raising
the vehicle with jack improperly
positioned will damage the ve-
hicle or may allow the vehicle
to fall off the jack and cause
personal injury.
Never get under the vehicle
when the vehicle is supported
by the jack alone.
Use the jack only for lifting
your vehicle during wheel
changing.
Do not raise the vehicle with
someone in the vehicle.
When raising the vehicle, do
not put an object on or under
the jack.
Raise the vehicle only high
enough to remove and change
the tire.NOTICE
Do not continue driving with a
deflated tire. Driving even a shortdistance can damage a tire be-yond repair.
ÐRequired tools and spare
tire

4RUNNER (1998)
Cover
(on some models)
1. Get the required tools and spare tire.
1. Tool bag
2. Jack handle
3. Jack
To prepare yourself for an emergency,
you should fam iliarize yourself with
the use of the jack, each of the tools
and their storage locations.

4RUNNER (1998)
Turn the jack joint by hand.
To remove: Turn the joint in direction
1 until the jack is free.
To store: Turn the joint in direction 2
until the jack is firmly secured to pre-
vent it flying forward during a collision
or sudden braking.

4RUNNER (1998)
To remove the spare tire:
1. Insert the end of the jack handle into the lowering screw and turn it
counterclockwise.
2. After the tire is lowered completely to the ground, remove the holding
bracket.
When storing the spare tire, put it in
place with the outer side of the wheel
facing up. Then secure the tire, taking
care that the tire goes straight up
without catching on any other part, to
prevent it from flying forward during a
collision or s udden braking. ÐBlocking the wheel

4RUNNER (1998)
2. Block the wheel diagonally oppo-
site the flat tire to keep the ve-
hicle from rolling when it is
jacked up.
When blocking the wheel, place a
wheel block from the front for the
front wheels or from the rear for the
rear wheels. ÐRemoving wheel ornament

4RUNNER (1998)
Steel wheels
Aluminum wheels
3. Remove the wheel ornament.
Pry off the wheel ornament, using the
beveled end of the wheel nut wrench
as shown.

4RUNNER (1998)
CAUTION
Do not try to pull off the orna-
ment by hand. Take due care in
handling the ornament to avoid
unexpected personal injury.
ÐLoosening wheel nuts
4. Loosen all the wheel nuts.
Always loosen the wheel nuts before
raising the vehicle.
The nuts turn counterclockwise to
loosen. To get maximum leverage, fit
the wrench to the nut so that the
handle is on the right side, as shown
above. Grab the wrench near the end
of the handle and pull up on the han-
dle. Be careful that the wrench does
not slip off the nut. Do not remove the nuts yetÐjust un-
screw them about one- half turn.
ÐPositioning the jack

4RUNNER (1998)
5. Position the jack at the correct
jack point as shown.
Make sure the jack is positioned on
a level and solid place. ÐRaising your vehicle

4RUNNER (1998)
6. After making sure that no one is
in the vehicle, raise it high
enough so that the spare tire
can be installed.
Remember you will need more ground
clearance when putting on the spare
tire than when removing the flat tire.
To raise the vehicle, insert the jack
handle extension in to the jack (it is
a loose fit) and turn it clockwise with
the handle, making sure the handle
remains firmly fitted onto the jack
handle extension. As the jack touches
the vehicle and begins to fit, double-
check that it is properly positioned.
CAUTION
Never get under the vehicle when
the vehicle is supported by the
jack alone.
ÐChanging wheels
7. Remove the wheel nuts and change tires.
Lift the flat tire straight off and put it
aside.