belt TOYOTA 4RUNNER 1998 Owner's Guide

4RUNNER (1998)
1. Run the center lap belt through or
around the convertible seat follow-
ing the instructions provided by its
manufacturer and insert the tab
into the buckle taking care not to
twist the lap belt.
CAUTION
After inserting the tab, make
sure the tab and buckle are
locked and that the lap belt is
not twisted.
Do not insert coins, clips, etc.
in the buckle as this may pre-
vent you from properly latching
the tab and buckle.
If the seat belt does not
function normally, it cannot
protect your child from injury.
Contact your Toyota dealer
immediately. Do not use the
seat until the seat belt is fixed.

4RUNNER (1998)
2. While pressing the convertible seat
firmly against the seat cushion and
seatback, tighten the lap belt by
pulling its free end to hold the con-
vertible seat securely.

4RUNNER (1998)
CAUTION
Push and pull the child restraint
system in different directions to
be sure it is secure. Follow all
the installation instructions pro-
vided by its manufacturer.
3. To remove the convertible seat,
press the buckle- release button. ÐInstallation with 3- point
type seat belt

4RUNNER (1998)
1. Run the lap and shoulder belt
through or around the infant seat
following the instructions provided
by its manufacturer and insert the
tab into the buckle taking care not
to twist the belt. Keep the lap por-
tion of the belt tight.
CAUTION
After inserting the tab, make
sure the tab and buckle are
locked and that the lap and
shoulder portions of the belt
are not twisted.
Do not insert coins, clips, etc.
in the buckle as this may pre-
vent you from properly latching
the tab and buckle.
If the seat belt does not
function normally, it cannot
protect your child from injury.
Contact your Toyota dealer
immediately. Do not use the
seat until the seat belt is fixed.

4RUNNER (1998)
2. Fully extend the shoulder belt to
put it in the lock mode. When the
belt is then retracted even slightly,
it cannot be extended.
To hold the infant seat securely, make
sure the belt is in the lock mode be-
fore letting the belt retract.

4RUNNER (1998)
3. While pressing the infant seat firm-
ly against the seat cushion and
seatback, let the shoulder belt re-
tract as far as it will go to hold the
infant seat securely.

4RUNNER (1998)
CAUTION
Make sure the seat belt is secure-
ly locked. Also make sure the
child restraint system is secure
by pushing and pulling it in dif-
ferent directions. Follow all the
installation instructions provided
by its manufacturer.
4. To remove the infant seat, press
the buckle- release button and allow
the belt to retract completely. The
belt will move freely again and be
ready to work for an adult or older
child passenger.

4RUNNER (1998)
1. Run the lap and shoulder belt
through or around the convertible
seat following the instructions pro-
vided by its manufacturer and in-
sert the tab into the buckle taking
care not to twist the belt. Keep the
lap portion of the belt tight.
CAUTION
After inserting the tab, make
sure the tab and buckle are
locked and that the lap and
shoulder portions of the belt
are not twisted.
Do not insert coins, clips, etc.
in the buckle as this may pre-
vent you from properly latching
the tab and buckle.
If the seat belt does not
function normally, it cannot
protect your child from injury.
Contact your Toyota dealer
immediately. Do not use the
seat until the seat belt is fixed.

4RUNNER (1998)
2. Fully extend the shoulder belt to
put it in the lock mode. When the
belt is then retracted slightly, it
cannot be extended.
To hold the convertible seat securely,
make sure the belt is in the lock
mode before letting the belt retract.

4RUNNER (1998)
3. While pressing the convertible seat
firmly against the seat cushion and
seatback, let the shoulder belt re-
tract as far as it will go to hold the
convertible seat securely.