light TOYOTA AVALON 2000 Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2000, Model line: AVALON, Model: TOYOTA AVALON 2000Pages: 352, PDF Size: 3.15 MB
Page 147 of 352
'00 AVALON U (L/O 9908)
146
If the light lit during driving goes out and
does not come on again, it is a normal
operation.
CAUTION
If the ABSº warning light remains on
together with the brake system warn-
ing light, immediately stop your ve-
hicle at a safe place and contact your
Toyota dealer.
In this case, the vehicle may become
harder to control or skid during hard
braking or braking on slippery road
surfaces.
(i) Open Door Warning Light
This light remains on until all the doors
are completely closed.
(j) Rear Light Failure Warning Light
If this light comes on when the headlight
switch is turned on (at the position 1 or
position 2), it indicates that one or more
of the tail lights are burned out.
If it comes on when the brake pedal is
depressed, one or more stop lights are
burned out.
Have defective bulbs replaced as soon as
possible.(k) SRS Warning Light
This light will come on when the igni-
tion key is turned to the ACCº or
ONº position. After about 6 seconds,
the light will go off. This means the
system of the airbags and front seat
belt pretensioners are operating proper-
ly.
This warning light system monitors the
airbag sensor assembly, front airbag sen-
sors, side airbag sensors, inflators, front,
seat belt pretensioner assemblies, warning
light, interconnecting wiring and power
sources.
If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle.
The light does not come on when the
ignition key is turned to the ACCº or
ONº position or remains on.
The light comes on or flashes while
driving.
(l) VSCº Warning Light
The light warns that when there is a prob-
lem somewhere in the vehicle skid control
system or traction control system.
The light will come on when the ignition
key is turned to ONº, and will go off after
about a few seconds.
If the VSCº warning light comes on, the
vehicle skid control system and traction
control system do not work. However, as
conventional braking operates when ap-
plied, there is no problem to continue your
driving.
If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle:
The VSCº warning light does not come
on after the ignition is turned to on.
The VSCº warning light is left on after
the ignition is turned to on.
The VSCº warning light comes on
while driving without pushing VSC
OFFº switch.
ProCarManuals.com
Page 148 of 352
'00 AVALON U (L/O9908)
147
(m) VSC OFFº Indicator Light
The light warns that when there is a prob-
lem somewhere in the vehicle skid control
system or traction control system.
The light will come on when the ignition
key is turned to ONº, and will go off after
about a few seconds.
If the VSC OFFº indicator light comes on,
the vehicle skid control system and trac-
tion control system do not work. However,
as conventional braking operates when ap-
plied, there is no problem to continue your
driving.
If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle:
The VSC OFFº indicator light does not
come on after the ignition is turned to
on.
The VSC OFFº indicator light is left on
after the ignition is turned to on.
The VSC OFFº indicator light comes
on while driving without pushing VSC
OFFº switch.(n) Low Windshield Washer Fluid Level
Warning Light
The light warns that the windshield washer
fluid level is too low. Add washer fluid at
your earliest opportunity. (For instructions,
see Adding washer fluidº in Section 7- 3.)
(o) Key Reminder Buzzer
This buzzer reminds you to remove the
key when you open the driver 's door with
the ignition key in the ACCº or LOCKº
position. CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light and low windshield
washer fluid level warning light)
1. Apply the parking brake.
2. Open one of the doors. The open door warning light should
come on.
3. Close the door. The open door warning light should go
off.
4. Turn the ignition key to ACCº. The SRS warning light should come on.
It goes off after about 6 seconds.
5. Turn the ignition key to ONº, but do not start the engine.
All the service reminder indicators ex-
cept the open door warning light and
SRS warning light should come on. The
ABSº, VSCº, VSC OFFº and slip indi-
cator lights go off after a few seconds.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, either the bulb is burned out or the
circuit is in need of repair. Have it
checked by your Toyota dealer as soon as
possible.
ProCarManuals.com
Page 156 of 352
'00 AVALON U (L/O9908)
155
STARTºÐStarter motor on. The key
will return to the ONº position when
released.
For starting tips, see Section 3.
ONºÐEngine on and all accessories
on.
This is the normal driving position.
ACCºÐAccessories such as the radio
operate, but the engine is off.
If you leave the key in the ACCº or
LOCKº position and open the driver's
door, a buzzer will remind you to remove
the key.
LOCKºÐEngine is off and the steering
wheel is locked. The key can be re-
moved only at this position.You must push in the key to turn the key
from ACCº to the LOCKº position. The
selector lever must be in the Pº position
before pushing the key.
Vehicles with engine immobiliser systemÐ
Once you remove the key, the engine im-
mobiliser system is automatically set. (See
Engine immobiliser systemº in Section
1- 2.)
When starting the engine, the key may
seem stuck at the LOCKº position. To
free it, first be sure the key is pushed all
the way in, and then rock the steering
wheel slightly while turning the key gently.
NOTICE
Do not leave the key in the ONº
position if the engine is not running.The battery will discharge and theignition could be damaged.
Ignition switch with steering
lock
ProCarManuals.com
Page 158 of 352
'00 AVALON U (L/O9908)
157
(b) Overdrive switch
You can select either a third gear (with
overdrive off) or fourth gear (with over-
drive on) by pushing this switch.
To turn the overdrive off, push the switch.
The O/D OFFº indicator light should come
on. To turn the overdrive on again, push
the switch again. The O/D OFFº indicator
light should go off.
Always drive your vehicle with the over-
drive on for better fuel economy and
quieter driving.
If the engine is turned off when the over-
drive is off and restarted, the overdrive
will automatically be on.When the cruise control is being used,
even if you downshift the transmission by
pushing and releasing the overdrive
switch, engine braking will not applied be-
cause the cruise control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise controlº in this section.
(c) Normal driving
1. Start the engine as instructed in How to start the engineº in Section 3. The
transmission must be in Pº or Nº.
2. With your foot holding down the brake pedal, shift the selector lever to Dº.
When the lever is in the Dº position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc.
Always turn the overdrive on for better
fuel economy and quieter driving. If the
engine coolant temperature is low, the
transmission will not shift into the over-
drive gear even with the overdrive on.
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake pedal. Depress the accelerator pedal
slowly for smooth starting.
(d) Using engine braking
To use engine braking, you can downshift
the transmission as follows:
Push the overdrive switch. The O/D
OFFº indicator light will come on and
the transmission will downshift to the
third gear.
Shift into the 2º position. The trans-
mission will downshift to the second
gear when the vehicle speed drops
down to or lower than 132 km/h (82
mph), and stronger engine braking will
be enabled.
Shift into the Lº position. The trans-
mission will downshift to the first gear
when the vehicle speed drops down to
or lower than 59 km/h (36 mph), and
maximum engine braking will be en-
abled.
When the cruise control is being used,
even if you downshift the transmission by
pushing and releasing the overdrive
switch, engine braking will not applied be-
cause the cruise control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise controlº in this section.
ProCarManuals.com
Page 162 of 352
'00 AVALON U (L/O9908)
161
(b) Overdrive switch
You can select either a third gear (with
overdrive off) or fourth gear (with over-
drive on) by pushing this switch.
To turn the overdrive off, push the switch.
The O/D OFFº indicator light should come
on. To turn the overdrive on again, push
the switch again. The O/D OFFº indicator
light should go off.
Always drive your vehicle with the over-
drive on for better fuel economy and
quieter driving.
If the engine is turned off when the over-
drive is off and restarted, the overdrive
will automatically be on.When the cruise control is being used,
even if you downshift the transmission by
pushing and releasing the overdrive
switch, engine braking will not applied be-
cause the cruise control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise controlº in this section.
(c) Normal driving
1. Start the engine as instructed in How to start the engineº in Section 3. The
transmission must be in Pº or Nº.
2. With your foot holding down the brake pedal, shift the selector lever to Dº.
When the lever is in the Dº position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc.
Always turn the overdrive on for better
fuel economy and quieter driving. If the
engine coolant temperature is low, the
transmission will not shift into the over-
drive gear even with the overdrive on.
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake pedal. Depress the accelerator pedal
slowly for smooth starting.
(d) Using engine braking
To use engine braking, you can downshift
the transmission as follows:
Push the overdrive switch. The O/D
OFFº indicator light will come on and
the transmission will downshift to the
third gear.
Shift into the 2º position. The trans-
mission will downshift to the second
gear when the vehicle speed drops
down to or lower than 132 km/h (82
mph), and stronger engine braking will
be enabled.
Shift into the Lº position. The trans-
mission will downshift to the first gear
When the vehicle speed drops down to
or lower than 59 km/h (36 mph), and
maximum engine braking will be ap-
plied.
When the cruise control is being used,
even if you downshift the transmission by
pushing and releasing the overdrive
switch, engine braking will not applied be-
cause the cruise control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise controlº in this section.
ProCarManuals.com
Page 165 of 352
'00 AVALON U (L/O 9908)
164
Traction control system
The traction control system automatical-
ly helps control the spinning of the
front wheels which may occur when ac-
celerating on slippery road surfaces,
thus assisting driver to control the driv-
ing power of the front wheels.
Leave the system on during ordinary
driving so that it can operate when
needed. When traction control is ap-
plied, the slip indicator light blinks.
While the VSCº warning light and VSC
OFFº indicator light come on, the traction
control system cannot be operated.You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the traction
control system is in the self- check mode,
and does not indicate malfunction.
When the traction control system is oper-
ating, you may feel vibration or noise of
your vehicle, caused by operation of the
brakes. This indicates the system is func-
tioning properly.
When getting the vehicle out of mud or
new snow, etc. the traction control system
will help operate to prevent the wheels
from spinning.You can turn off the traction control
system by pushing the VSC OFFº
switch. The VSC OFFº indicator light
will come on. Pushing the VSC OFFº
switch a second time turns on the trac-
tion control system again and the VSC
OFFº indicator light will go off. At this
time, the vehicle skid control also turns
off and on simultaneously.
ProCarManuals.com
Page 166 of 352
'00 AVALON U (L/O9908)
165
TRACTION CONTROL SYSTEM FAILURE
WARNING
These lights warn that when there is a
problem somewhere in the traction control
system.
The lights will come on when the ignition
key is turned to ONº, and will go off after
about a few seconds.
If the VSCº warning light and VSC OFFº
indicator light come on, the traction con-
trol system does not work. However, as
conventional braking operates when ap-
plied, there is no problem to continue your
driving.If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle:
The VSCº warning light and/or VSC
OFFº indicator light do/does not come
on after the ignition is turned to on.
The VSCº warning light and VSC
OFFº indicator light are left on after the
ignition is turned to on.
The VSCº warning light and VSC
OFFº indicator light comes on while
driving without pushing VSC OFFº
switch.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicle and
power to the front wheels can not be
maintained, even though the traction
control system is in operation. Do not
drive the vehicle under any speed or
maneuvering conditions which will
cause the vehicle to lose traction. In
situations where the road surface is
covered with ice or snow, your ve-
hicle should be fitted with snow tires
or tire chains. Always drive at ap-
propriate and cautious pace.
ProCarManuals.com
Page 167 of 352
'00 AVALON U (L/O 9908)
166
Vehicle skid control system
The vehicle skid control system helps
provide comprehensive control of the
systems such as an anti- lock brake
system, brake assist system, traction
control, engine control, etc. This sys-
tem automatically controls the output of
the brakes or engine to help prevent
the vehicle from skidding when corner-
ing on a slippery road surface or
abrupt steering wheel operation occurs.If the vehicles is going to skid during
driving, the slip indicator light flashes and
an alarm sounds intermittently.
The vehicle skid control system activates
when the vehicle speed is about more
than 15 km/h (9 mph).
While the VSCº warning light and VSC
OFFº indicator light come on, the vehicle
skid control system cannot be operated.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the vehicle
skid control is in the self- check mode and
does not indicate a malfunction.You can turn off the vehicle skid con-
trol system by pushing the VSC OFFº
switch. The VSC OFFº indicator light
will come on. Pushing the VSC OFFº
switch a second time turns the system
again and the VSC OFFº indicator light
will go off. At this time, the traction
control also turns off and on simulta-
neously.
When you turn the ignition switch on, this
system always turns on.
ProCarManuals.com
Page 168 of 352
'00 AVALON U (L/O9908)
167
CAUTION
Do not rely excessively on the ve-
hicle skid control system. Even if
the vehicle skid control system is
operating, it is not that your vehicle
is absolutely safe. Reckless driving
will result in an unexpected acci-
dent. Always keep safety driving in
mind. If the slip indicator light fla-
shes and/or an alarm sounds, spe-
cial care should be taken while
driving.
Only use tires of specified size. The
size, manufacturer, brand and tread
pattern for all 4 tires should be the
same. If you use the tires other
than specified, or different type or
size, the vehicle skid control sys-
tem may not function correctly.
When replacing the tires or wheels,
contact your Toyota dealer.VEHICLE SKID CONTROL SYSTEM
FAILURE WARNING
These lights warn that when there is a
problem somewhere in the vehicle skid
control system.
The lights will come on when the ignition
key is turned to ONº, and will go off after
about a few seconds.
If the VSCº warning light and VSC OFFº
indicator light come on, the vehicle skid
control system does not work. However,
as conventional braking operates when ap-
plied, there is no problem to continue your
driving.If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle:
The VSCº warning light and/or VSC
OFFº indicator light do/does not come
on after the ignition is turned to on.
The VSCº warning light and VSC
OFFº indicator light are left on after the
ignition is turned to on.
The VSCº warning light and VSC
OFFº indicator light comes on while
driving without pushing VSC OFFº
switch.
ProCarManuals.com
Page 169 of 352
'00 AVALON U (L/O 9908)
168
Parking brake
Ty p e A
Ty p e B
When parking, firmly apply the parking
brake to avoid inadvertent creeping.
To set: Fully depress the parking brake
pedal. For better holding power, first de-
press the brake pedal and hold it while
setting the parking brake.
To release: Depress the parking brake
pedal while depressing the brake pedal.
To remind you that the parking brake is
set, the parking brake reminder light in
the instrument panel remains on until you
release the parking brake.
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
Cruise control
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) with your foot off the
accelerator pedal.
Your cruising speed can be maintained
although a slight speed change may occur
when driving up or down gradient, within
the limits of engine performance. On
steeper hills, a greater speed change will
occur so it is better to drive without the
cruise control.
When the cruise control is on, the driving
pattern of the automatic transmission is
fixed in the normal position, regardless of
the position of the selector switch.
ProCarManuals.com