TOYOTA AVALON 2001 Service Repair Manual
Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 1091 of 1897
N21463
(Example)
Inspection of SET Switch
2
1
DI-514- DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)
670 Author: Date:
2001 AVALON (RM808U)
NG
2 Check seat memory switch.
PREPARATION:
Disconnect seat memory switch connector.
CHECK:
Check continuity of each terminal.
OK:
Switch positionTerminal
SET switch ON1 - 2
Memory switch 12 - 3
Memory switch 22 - 4
NG Replace seat memory switch.
OK
3 Check harness and connectors between Seat Position Control ECU and seat
memory switch (See page IN-30).
NG Repair or replace harness or connector.
OK
Check and replace Seat Position Control
ECU.
Page 1092 of 1897
DI0FR-06
POWER SEAT CONTROL SYSTEM Check Sheet
Inspector 's name:
Customer 's Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading / /km
Mile
How Often Problem Occurs
/ /
Continuous Intermittent ( Times a day) Brought in
Manual Function
does not operate. Slide Front Vertical Rear Vertical Reclining
Memory function does not operate.
Position return function does not stop when brake pedal is depressed.
Date Problem First Occurred
Problem Symptom
Slide Front Vertical Rear Vertical
Does not operate in any conditions
Only with key inserted
Only with key not inserted
Only with memory & return switch 1 or 2 Return Function
does not operate.
- DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)DI-489
645 Author: Date:
2001 AVALON (RM808U)
CUSTOMER PROBLEM ANALYSIS CHECK
Page 1093 of 1897
DI0FP-07
Customer Problem Analysis
Vehicle Brought to Workshop
Problem Symptom ConfirmationSymptom Simulation Symptom does not occur
Problem Symptom Table
Circuit Inspection
Identification of Problem
Repair
Confirmation Test
EndTitles inside
are titles of pages in this
manual with the page number indicated in the
bottom portion. See the indicated pages
for detailed explanations. 1
23
4
5
7P. DI-489
P. DI-493
P. IN-20
P. DI-494 - DI-513
Symptom occur
6
Parts Inspection
Step 5, 7 : Diagnostic steps permitting the use
of the hand-held tester and break-
out-box.
DI-488- DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)
644 Author: Date:
2001 AVALON (RM808U)
POWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)
HOW TO PROCEED WITH TROUBLESHOOTING
Perform troubleshooting in accordance with the procedure on the following page.
Page 1094 of 1897
DI0FT-05
I12537Front Vertical MotorEngine Room Junction Block
ECU-B NO. 1 Fuse
Instrument Panel Junction Block
PWR SEAT M-Fuse
Reclining Motor
Power Seat Control ECU
Rear Vertical
Motor
Slide MotorLumbar Support Switch
Seat Memory Switch
Power Seat Control Switch DI-490
- DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)
646 Author: Date:
2001 AVALON (RM808U)
PARTS LOCATION
Page 1095 of 1897
DI0FV-08
- DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)DI-493
649 Author: Date:
2001 AVALON (RM808U)
PROBLEM SYMPTOMS TABLE
Perform troubleshooting of the circuits for the applicable problem symptom in the order given in the chart
below. Proceed to the page located for each circuit.
HINT:
If the instruction ºProceed to next circuit inspection shown on problem symptom tableº is given in the
flow chart for each circuit, proceed to the circuit with the next highest number in the table to continue
the check.
If the trouble still reappears even though there are no abnormalities in any of the other circuits, then
check and replace the Seat Position Control ECU as the last step.
SymptomSuspect AreaSee page
Both manual & return functions do not operate(All functions).
3. +B power source circuit
4. Power seat control switch circuit
5. Motor circuit
6. Power seat control ECUDI-494
DI-510
DI-500
IN-30
Both manual & return functions do not operate(One function only).1. Motor circuit
2. Power seat control ECUDI-500
IN-30
One or all functions do not operate for manual operation only.1. Power seat control switch circuit
2. Power seat control ECUDI-510
IN-30
Memory function does not operate.
1. Power seat memory switch circuit
2. Ignition switch circuit
3. Power seat control ECUDI-510
DI-508
IN-30
Return operation does not stop when brake pedal is depressed.1. Stop light switch circuit
2. Power seat control ECUDI-662
IN-30
Only return function does not operate or operates a little, then
stops (All return functions).
1. Power seat memory switch circuit
2. ECU power source circuit
3. Position sensor power source circuit
4. Power seat control ECUDI-513
DI-497
DI-504
IN-30
Only return function does not operate or operates a little, then
stops (Only one return function).1. Position sensor circuit
2. Power seat control ECUDI-506
IN-30
Page 1096 of 1897
DI6KY-01
I11581
P20P21
- DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)DI-491
647 Author: Date:
2001 AVALON (RM808U)
TERMINALS OF ECU
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
SSFV e SGND
(P21-4 e P21-19)L-B e BRFront vertical operation0 V e 8 V
SSRL e SGND
(P21-17 e P21-19)L-W e BRRear vertical operation0 V e 8 V
SSRR e SGND
(P21-16e P21-19)L-R e BRReclining operation0 V e 8 V
PVCC e SGND
(P21-5 e P21-19)R e BRPower seat operation8 V
FDWN e Body Ground RBSeat lowered using front vertical SWBelow 1 VFDWN e Body Ground
(P21-24 eBody Ground)R-BOthers10 - 14 V
IG e Body Ground
(P21-13 eBody Ground)R-BIgnition SW ON10 - 14 V
SYSB e Body Ground
(P21-25 eBody Ground)W-GAlways10 - 14 V
MPX1Bd G dMultiplex communication circuit signals0 V e 12 VMPX1 e Body Ground
(P21-14 eBody Ground)G-WOthersResistance
(Approx. 2.5 kW)
SGND e Body Ground
(P21-19 eBody Ground)BRAlwaysBelow 1 V
SSRS e SGND
(P21-3 eP21-19)L e BRSlide operation0 V e 8 V
SLDF e Body Ground BSeat moved forward using slide SWBelow 1 VSLDF e Body Ground
(P21-6 eBody Ground)BOthers10 - 14 V
SLDR e Body Ground BRSeat moved to rear using slide SWBelow 1 VSLDR e Body Ground
(P21-8 eBody Ground)B-ROthers10 - 14 V
LUP e Body Ground RWSeat raised using rear vertical SWBelow 1 VLUP e Body Ground
(P21-22 eBody Ground)R-WOthers10 - 14 V
LDWN e Body Ground RYSeat lowered using rear vertical SWBelow 1 VLDWN e Body Ground
(P21-1 1 eBody Ground)R-YOthers10 - 14 V
FUP e Body Ground BYSeat raised using front vertical SWBelow 1 VFUP e Body Ground
(P21-23 eBody Ground)B-YOthers10 - 14 V
RCLF e Body Ground GBSeat moved forward using reclining SWBelow 1 VRCLF e Body Ground
(P21-10 eBody Ground)G-BOthers10 - 14 V
RCLR e Body Ground GSeat moved to rear using reclining SWBelow 1 VRCLR e Body Ground
(P21-12 eBody Ground)GOthers10 - 14 V
RCL- e GND RBWBSeat moved to rear using reclining SW10 - 14 VRCL e GND
(P20-1 e P20-7)R-B e W-BOthersBelow 1 V
Page 1097 of 1897
DI-492- DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)
648 Author: Date:
2001 AVALON (RM808U) RCL+ e GND
RWWBSeat moved forward using reclining SW10 - 14 VRCL+ e GND
(P20-2 eP20-7)R-W e W-BOthersBelow 1 V
SLD- e GNDLBWBSeat moved to rear using slide SW10 - 14 VSLD e GND
(P20-3 eP20-7)L-B e W-BOthersBelow 1 V
SLD+ e GNDLWBSeat moved forward using slide SW10 - 14 VSLD+ e GND
(P20-4 eP20-7)L e W-BOthersBelow 1 V
LFT- e GND RWBSeat lowered using rear vertical SW10 - 14 VLFT e GND
(P20-5 eP20-7)R e W-BOthersBelow 1 V
LFT+ e GND LYWBSeat raised using rear vertical SW10 - 14 VLFT+ e GND
(P20-6 eP20-7)L-Y e W-BOthersBelow 1 V
GND e Body Ground
(P20-7 eBody Ground)W-BAIwaysBelow 1 V
+B e Body Ground
(P20-8 eBody Ground)L-OAlways10 - 14 V
FRV- e GND LWWBSeat lowered using front vertical SW10 - 14 VFRV e GND
(P20-9 eP20-7)L-W e W-BOthersBelow 1 V
FRV+ e GND LRWBSeat raised using front vertical SW10 - 14 VFRV+ e GND
(P20-10 eP20-7)L-R e W-BOthersBelow 1 V
MMRY e SWEGYWBSet switch position is OFF.10 - 14 VMMRY e SWE
(P21-9 e P21-7)G-Y e W-BSet switch position is ON.Below 1 V
SW1 e SWEGWWBMemory Switch 1 position is OFF.10 - 14 VSW1 e SWE
(P21-21 e P21-7)G-W e W-BMemory Switch 1 position is ON.Below 1 V
SW2 e SWEYWBMemory Switch 2 position is OFF.10 - 14 VSW2 e SWE
(P21-20 e P21-7)Y e W-BMemory Switch 2 position is ON.Below 1 V
Page 1098 of 1897
DI4CK-03
H01451
Y-B
D+ C6 14Airbag Sensor Assembly
13
C6D- Y 1
2
Spiral
Cable D Squib DI-362
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
518 Author: Date:
2001 AVALON (RM808U)
CIRCUIT INSPECTION
DTC B0100/13 Short in D Squib Circuit
CIRCUIT DESCRIPTION
The D squib circuit consists of the airbag sensor assembly, spiral cable and steering wheel pad.
It causes the airbag to deploy when the airbag deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS-3.
DTC B0100/13 is recorded when a short is detected in the D squib circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0100/13
Short circuit between D+ wire harness and D- wire har-
ness of squib
D squib malfunction
Spiral cable malfunction
Airbag sensor assembly malfunctionSteering wheel pad (D squib)
Spiral cable
Airbag sensor assembly
Wire harness
WIRING DIAGRAM
Page 1099 of 1897
H01001H02142H02193
D SquibSpiral
Cable
Airbag
Sensor
Assembly
D+
(-)(+) D-
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-363
519 Author: Date:
2001 AVALON (RM808U)
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-475).
2 Check D squib circuit.
PREPARATION:
Release the airbag activation prevention mechanism of the
connector (on the airbag sensor assembly side) between the
airbag sensor assembly and the spiral cable (See page
DI-349).
CHECK:
For the connector (on the spiral cable side) between the spiral
cable and the steering wheel pad, measure the resistance be-
tween D+ and D-.
OK:
Resistance: 1 MW or Higher
NG Go to step 5.
OK
Page 1100 of 1897
FI1390AB0118
R13006AB0119H01002H07478
D SquibSpiral
Cable
Airbag
Sensor
Assembly
E1TcON
or
DTC B0100/13
DLC1"u
ACC
DI-364
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
520 Author: Date:
2001 AVALON (RM808U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Connect negative (-) terminal cable to the battery, and
wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ACC or ON and wait at least for
20 seconds.
(b) Clear the DTC stored in memory (See page DI-349).
(c) Turn the ignition switch to LOCK, and wait at least for 20
seconds.
(d) Turn the ignition switch to ACC or ON, and wait at least
for 20 seconds.
(e) Check the DTC (See page DI-349).
OK:
DTC B0100/13 is not output.
HINT:
Codes other than code B0100/13 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK