engine TOYOTA AVALON 2001 Service Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 228 of 1897
Will you register the
next key?
No Ye s
Insert already registered master key in the key
cylinder
Depress and release the acceleration pedal 5
times.
Depress and release the brake pedal 6 times,
and remove the master key.
Insert key to be registered in key cylinder.
Depress and release the acceleration pedal 1
time. (Security indicator blinks)
The registration mode completes when pulling
out the key within 10 secs. and the brake pedal
is depressed or after indicator is off 10 secs.
pass. Within 10 secs.Within 15 secs.
Within 20 secs.
Within 10 secs.
Within 10 secs.
After 60 secs. additional master key is regis-
tered. (Security indicator is OFF)
BE-174
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
1778 Author: Date:
2001 AVALON (RM808U)
2. REGISTRATION OF ADDITIONAL MASTER KEY
There are 2 ways for registration of additional master key, one is depressing brake pedal and acceleration
pedal and the other is using hand-held tester.
HINT:
It is possible to register up to 7 master key codes including the already registered key code.
When any operation time described below is over, registration mode completes.
When the next procedure is performed while the timer is working, the timer completes counting time,
then next timer starts.
(1) Depressing brake pedal and acceleration pedal:
Page 229 of 1897
Insert already registered master key in the key cylinder
and turn the ignition switch ON.
Listing hand-held tester select master key registration.
Remove the master key.
Insert key to be registered in key cylinder.
(Security indicator blinks)
After 60 secs., additional master key is registered.
(Security indicator OFF)
The registration mode completes when pulling out the key
within 10 secs. and the brake pedal is depressed or after
indicator is off 10 secs. pass.Within 20 secs.
Within 10 secs.
HINT:
Please follow the screen of the hand-held tester for more detailed procedure.
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE-175
1779 Author: Date:
2001 AVALON (RM808U)
(2) Using hand-held tester:
Page 230 of 1897
Will you register the
next key?
No Ye s
Insert already registered master key in the key
cylinder
Depress and release the acceleration pedal 4
times.
Depress and release the brake pedal 5 times,
and remove the master key.
Insert key to be registered in key cylinder.
Depress and release the acceleration pedal 1
time. (Security indicator blinks)
The registration mode completes when pulling
out the key within 10 secs. and the brake pedal
is depressed or after indicator is off 10 secs.
pass. Within 10 secs.Within 15 secs.
Within 20 secs.
Within 10 secs.
Within 10 secs.
After 60 secs. additional sub-key is registered.
(Security indicator is OFF)
BE-176
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
1780 Author: Date:
2001 AVALON (RM808U)
3. REGISTRATION OF ADDITIONAL SUB-KEY
There are 2 ways for registration of additional sub-key, one is depressing brake pedal and acceleration ped-
al and the other is using hand-held tester.
HINT:
It is possible top register up to 3 sub-key codes including the already registered key code.
When any operation time described below is over, registration mode completes.
When the next procedure is performed while the timer is working, the timer completes counting time,
then next timer starts.
(1) Depressing brake pedal and acceleration pedal:
Page 231 of 1897
Listing TOYOTA hand-held tester select sub-key regis-
tration.
Remove the master key.
Insert key to be registered in key cylinder.
(Security indicator blinks)
After 60 secs., additional sub-key is registered.
(Security indicator OFF)
The registration mode completes when pulling out the key
within 10 secs. and the brake pedal is depressed or after
indicator is off 10 secs. pass.Within 20 secs.
Within 10 secs.
Insert already registered master key in the key cylinder
and turn the ignition switch ON.
HINT:
Please follow the screen of the hand-held tester for more detailed procedure.
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE-177
1781 Author: Date:
2001 AVALON (RM808U)
(2) Using hand-held tester:
Page 232 of 1897
1. Insert master key in the key cylinder.
2. Depress and release the acceleration pedal 6 times.
3. Depress and release the brake pedal 7 times.
4. Remove the master key.
HINT:
If the key cannot be pulled out within 30 sec. from the first brake
depression in the step 3, the key code deletion is canceled.(Key code erased)
Within 15 sec.
Within 20 sec.
Within 10 sec.
END
5. Leave the vehicle more than 20 sec. without any
operation.
BE-178
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
1782 Author: Date:
2001 AVALON (RM808U)
4. ERASURE OF TRANSPONDER KEY CODE
There are 2 ways for erasure of transponder key code, one is depressing brake pedal and acceleration pedal
and the other is using hand-held tester.
NOTICE:
All other master and sub-key codes are deleted leaving the master key code to use the operation.
When using the key which was used before deleting, it is necessary to register the code again.
HINT:
When any operation time described below is over, registration mode completes.
When the next procedure is performed while the timer is working, the timer completes counting time,
then next timer starts.
(1) Depressing brake pedal and acceleration pedal:
Page 233 of 1897
2. Require key code deletion from hand-held tester.
(Security indicator blinks)
3. Remove the master key.
HINT: END
Within 10 secs.
(Key code erased) 1. Insert already registered master key in the key cylinder
and turn the ignition switch ON.
When the key cannot be pulled out in the step 3, key code deletion is canceled.
(Security indicator is OFF)
Please follow the screen of the hand-held tester for more detailed procedure.
- BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE-179
1783 Author: Date:
2001 AVALON (RM808U)
(2) Using hand-held tester:
Page 244 of 1897
I18944
0.4 °
3 m (9.84 ft) H 20.9 mm
(0.823 in.)
7
V RH Line
90 °
V LH Line4V LH LineV Line V RH Line 65
6
V LH LineV Line
V RH Line 6
5
6
H4
O: step No.
7
H4
20.9 mm
(0.823 in.)
20.9 mm
(0.823 in.) 1,342mm (52.8 in.) Low Beam:
High Beam:20.9 mm
(0.823 in.)
20.9 mm
(0.823 in.)
1,342mm (52.8 in.)
1,342mm
(52.8 in.) Hight Bearm
Low Bearm BE-24
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1628 Author: Date:
2. ADJUST HEADLIGHT AIM ONLY
(a) Place the vehicle in the following conditions.
The area around the headlight is not deformed.
The vehicle is parked on a level surface.
Tire inflation pressure is the specified value.
A driver is in the driver's seat and the vehicle is in a state ready for driving (with a tank full).
The vehicle has been bounced several times.
(b) Check the headlight aiming.
(1) Prepare a thick white paper.
(2) Stand the paper perpendicular to the ground at the position 9.84 ft away from the headlights.
(3) Ensure that the center line of the vehicle and the paper face forms a 90-degree angle as shown
in the illustration.
(4) Draw a horizontal line (H line) on the paper, showing where the headlights should strike.
(5) Draw a vertical line (V line) to where the center line of the vehicle is to be.
(6) Draw 2 vertical lines (by connecting the low and high beam center marks) to where the both head-
lights should strike (V RH and V LH lines).
(7) Draw a horizontal line (by connecting the both low beam center marks) to where the headlights
should strike (H RH and H LH lines).
HINT:
The H RH and H LH line is 0.4° below the horizontal line (H line) of the light axis.
(8) Start the engine.
(9) Turn the headlights ON.
(10) Check that the headlights properly strike the position shown in the illustration.
(11) If not, adjust the lights in the vertical direction.
HINT:
As shown in the illustration, adjust each aim of the RH and LH lights.
(c) When adjusting it in the vertical direction:
Using adjusting bolt, adjust the headlight aim to within the specified range.
Page 250 of 1897
BE0HV-04
I12524
Relay Block No.7
D.R.L. No.2, No.3 and No.4 Relay
HEAD LH UPR Fuse (w/ DRL)
HEAD RH UPR Fuse (w/ DRL)
Engine Room Junction Block
H-LP LH Fuse (w/o DRL)
H-LP LH-LWR Fuse (w/ DRL)
H-LP RH Fuse (w/o DRL)
H-LP RH-LWR Fuse (w/ DRL)
DRL Fuse
Headlight Control Relay
Headlight
Driver Side Junction Block
Taillight Control Relay
BODY ECU
TAIL Fuse
TAIL Relay
Ignition Switch
Taillight
Combination Switch
Light Control Switch
Dimmer Switch
Automatic Light Control Sensor
DRL: Daytime Running Light
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-17
1621 Author: Date:
2001 AVALON (RM808U)
HEADLIGHT AND TAILLIGHT SYSTEM
LOCATION
Page 258 of 1897
BE212-01
BE-88
- BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
1692 Author: Date:
ADJUSTMENT
ENABLING/DISABLING AUTO DOOR LOCK FUNCTION
(a) To disable auto door lock:
(1) Enter the vehicle and shut all doors.
(2) Insert the key into the ignition cylinder and turn it to
the ON position (not ACC).
(3) Open the driver's door and keep it open.
(4) Turn the key to the LOCK position and remove it
from the ignition cylinder.
(5) Insert the key into the ignition cylinder and remove
it. Repeat this operation three more times. (End this
step with the key out of the ignition cylinder.)
(6) Push the ºUNLOCKº button on the driver's door
master switch 5 times within 10 seconds. Wait at
least 10 seconds and shut the driver's door.
(7) Verify auto lock operation has been disabled by
starting the engine, putting the vehicle into a gear
and releasing the brake pedal.
(b) To enable auto door lock:
Follow the same sequence as above, except step 6. In step 6,
push the ºLOCKº button on the driver's door master switch 5
times within 10 seconds. Wait at least 10 seconds and shut the
driver 's door.
Page 274 of 1897
BE1DF-01
I12522
Relay Block No.8Engine Room
Junction Block
Relay Block No.7
Instrument Panel Junction Block
- BODY ELECTRICALPOWER SOURCE
BE-9
1613 Author: Date:
2001 AVALON (RM808U)
POWER SOURCE
LOCATION