display TOYOTA AVALON 2001 Service Manual PDF

A00310
A09772
Engine Coolant Temp. SensorECM
5 V
THW
E2
E1 14
18 2
1G-Y
W
E5 E5 DI-32
- DIAGNOSTICSENGINE
188 Author
: Date
:
2001 AVALON (RM808U)
DTC P0115 Engine Coolant Temp. Circuit Malfunction
CIRCUIT DESCRIPTION
A thermistor built into the engine coolant temperature sensor changes the resistance value according to the
engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as in the intake air temperature circuit
malfunction shown on page DI-28.
If the ECM detects the DTC P0115, it operates the fail-safe function in which the engine coolant temperature
is assumed to be 80°C (176°C).
DTC No.DTC Detecting ConditionTrouble Area
P0115Open or short in engine coolant temp. sensor circuit

Open or short in engine coolant temp. sensor circuit

Engine coolant temp. sensor

ECM
HINT:
After confirming DTC P0115, use the OBD II scan tool or TOYOTA hand-held tester to confirm the engine
coolant temperature from the CURRENT DATA.
Temperature DisplayedMalfunction
-40°C (-40°F)Open circuit
140°C (284°F) or moreShort circuit
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs P0110, P0115, P0120 and P1410 are output simultaneously, E2 (sensor ground) may be open.

Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich etc. at the time of the malfunction.
DI07I-09

A11670
HTS
E03 AFR+
3.3 VECM
to Analog-Digital
Converter
to Analog-Digital
Converter
AFR-
AFL+ HAFR
3.3 V3.0 V
AFL-
OXSHAFL
3.0 VE04
E05
E1 E79
8 4
213
1220 11 E5
E5
E5
E5
E5
E5
E7
L-O
LG
B
B-R
L
B-W
BR
B-RB-R
LG
B B-W
B-W
B-W
B-W
B-W
BR
BR B From
Battery
From Terminal
MREL of ECMA/F Sensor
(Bank 1
Sensor 1)
J5 J/C
J7 J/CA/F Sensor
(Bank 2
Sensor 1)
Heated
Oxygen
Sensor
(Bank 1
Sensor 2)2
3
41
2
3
41
2
3
41 23
5
1
23
5
1 A/F Relay
EFI Relay Engine Room J/B
16
19
IK28 16
IK2 IK2II2
EC
1021
IK2
II2
EB
A
A
A12
13
9
2B
4 2B 2B2B
4 2FA/F
EFI
No.2 2
2GEFI
No.1
W-B
ED
BR
BR
BRBR B
B DI-44
- DIAGNOSTICSENGINE
200 Author
: Date
:
2001 AVALON (RM808U)

OBD II scan tool (excluding TOYOTA hand-held tester) displays the one fifth of the A/F sensor output
voltage which is displayed on the TOYOTA hand-held tester.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for determining
whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean
or rich, etc. at the time of the malfunction.

A00022
4-Pulse
Engine
ECM
Multi Display From
Speed Sensor4-Pulse
ABS Actuator
& ECU
A11086
Multi Display
18
M3 E73F V-W V-WECM
SPD5 V
122
3C 1J/B No.3
- DIAGNOSTICSENGINE
DI-99
255 Author
: Date
:
2001 AVALON (RM808U)
DTC P0500 Vehicle Speed Sensor Malfunction
CIRCUIT DESCRIPTION
This sensor is mounted in the combination meter. It contains a magnet which is rotated by the speedometer
cable.
Turning the reed switch ON and OFF 4 times for every revolution of the speedometer.
It is then transmitted to the Engine ECM. The Engine ECM determines the vehicle speed based on the fre-
quency of these pulse signals.
DTC No.DTC Detecting ConditionTrouble Area
No vehicle speed sensor signal to Engine & ECT ECU under
Combination meter
P0500/61
No vehicle speed sensor signal to Engine & ECT ECU under
th f ll i diti (2 t i d t ti l i )

Combination meter
Ohtid iitP0500/61the following conditions: (2 trip detection logic)
Open or short in speed sensor circuitg( g)
Vehicle is being driven
ECM
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for determining
whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean
or rich, etc. at the time of the malfunction.
DI082-09

A02030
E7 Connector
SPD
A02029
E7 ConnectorON
SPD(-) (+)
DI-100
- DIAGNOSTICSENGINE
256 Author
: Date
:
2001 AVALON (RM808U)
1 Check operation of speedometer.
CHECK:
Drive the vehicle and check if the operation of the speedometer in the combination meter is normal.
HINT:
The vehicle speed sensor is operating normally if the speedometer display is normal.
NG Check speedometer circuit (See page BE-43).
OK
2 Check for short in harness and connector between terminal SPD of ECM and
body ground.
PREPARATION:
(a) Remove the glove compartment (See page SF-83).
(b) Disconnect the E7 connector from the ECM.
CHECK:
Check the continuity between terminal SPD of the ECM con-
nector and body ground.
OK:
No continuity (1 MW or higher)
NG Repair or replace harness or connector.
OK
3 Check voltage between terminal SPD of ECM connector and body ground.
PREPARATION:
(a) Remove the glove compartment (See page SF-83).
(b) Disconnect the E7 connector from the ECM.
(c) Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal SPD of the ECM con-
nector and body ground.
OK:
Voltage: 9 - 14 V
NG Check for open in harness and connector be-
tween J/B No.3 and ECM (See page IN-30).

DI-106
- DIAGNOSTICSENGINE
262 Author
: Date
:
2001 AVALON (RM808U)
DTC P1130 A/F Sensor Circuit Range/Performance Mal-
function (Bank 1 Sensor 1)
DTC P1150 A/F Sensor Circuit Range/Performance Mal-
function (Bank 2 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-43.
DTC No.DTC Detecting ConditionTrouble Area
Voltage output* of A/F sensor remains at 3.8 V or more, or 2.8
V or less, during engine running after the engine is warmed up
(2 trip detection logic)
*: Output value changes at inside of ECM only

Open or short in A/F sensor circuit

A/F sensor
P1130
P1150Voltage output* of A/F sensor does not change from 3.30 V,
during engine running after the engine is warmed up (2 trip
detection logic)
*: Output value changes at the inside of ECM only
Air induction system

Fuel pressure

Injector

ECM
Open or short in A/F sensor circuit (2 trip detection logic)
HINT:

After confirming DTC P1130, use the OBD II scan tool or TOYOTA hand-held tester to confirm voltage
output of A/F sensor (AFS B1 S1/O2S B1 S1) from the CURRENT DATA.

The A/F sensor's output voltage and the short-term fuel trim value can be read using the OBD II scan
tool or TOYOTA hand-held tester.

The ECM controls the voltage of the AFR+, AFL+, AFR- and AFL- terminals of the ECM to the fixed
voltage. Therefore, it is impossible to confirm the A/F sensor output voltage without the OBDII scan
tool or TOYOTA hand-held tester.

OBD II scan tool (excluding TOYOTA hand-held tester) displays the one fifth of the A/F sensor output
voltage which is displayed on the TOYOTA hand-held tester.
WIRING DIAGRAM
Refer to DTC P0125 on page DI-43.
DI2H7-03

A00364
Vehicle Speed
60 - 120 km/h
(38 - 75 mph)
Idling
IG SW OFF
3 - 5 min.
Time
(a) (b)(c)(d)
- DIAGNOSTICSENGINE
DI-107
263 Author
: Date
:
2001 AVALON (RM808U)
CONFIRMATION DRIVING PATTERN
(a) Connect the TOYOTA hand-held tester to the DLC3.
(b) Switch the TOYOTA hand-held tester from the normal mode to the check mode (See page DI-3).
(c) Start the engine and warm it up with all the accessory switches OFF.
(d) Drive the vehicle at 60 - 120 km/h (38 - 75 mph) and engine speed at 1,400 - 3,200 rpm for 3 - 5 min.
HINT:
If a malfunction exists, the MIL will light up during step (d).
NOTICE:
If the conditions in this test are not strictly followed, detection of the malfunction will not be possible.
If you do not have a TOYOTA hand-held tester, turn the ignition switch OFF after performing steps
(c) and (d), then perform steps (c) and (d) again.
INSPECTION PROCEDURE
HINT:

If DTC P1130 is displayed, check Bank 1 Sensor 1 circuit.

If DTC P1150 is displayed, check Bank 2 Sensor 1 circuit.

Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
1 Are there any other codes (besides DTC P1130, P1150) being output?
YES Go to relevant DTC chart (See page DI-14).
NO

A11669
14
3 2
B-R
L LG-B
L-Y
LG 1
4
2
43
21
43
21
43
21
43
2
Ignition Coil
with Igniter
No.2
No.3
No.4
No.5
No.6
Noise
Filter B-Y W-BB-W
GR
13 No.1B-W
B-W B-W B-W
B-WB-Y
B-Y B-Y B-Y B-Y B-Y
W-B
W-B
W-B
W-B W-B
1
B-W
B-WW-B
B-W
B-W
B-WW-B W-B W-B
B-W
W-BIGT1
IGF IGT2
IGT3
IGT4
IGT5
IGT6 11
12
13
14
15
16
25 E4
E4
E4
E4
E4
E4
E4ECM
Battery
EC ED
115
2B
B-O
2F 1C28
3
IG Switch72
14 IG2 Reray
2G
2C 2CIG2
AM2 72
1J B-O
7
6W-R
W-R4
IF1Engine Room J/B
Driver Side J/BB
Fusible
Link
Block
FL
Main 1F6 F7
B-W
1 B-Y
B-Y B-Y B-Y
W-B
DI-1 18
- DIAGNOSTICSENGINE
274 Author
: Date
:
2001 AVALON (RM808U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P1300 is displayed, check No.1 ignition coil with igniter circuit.

If DTC P1305 is displayed, check No.2 ignition coil with igniter circuit.

If DTC P1310 is displayed, check No.3 ignition coil with igniter circuit.

If DTC P1315 is displayed, check No.4 ignition coil with igniter circuit.

If DTC P1320 is displayed, check No.5 ignition coil with igniter circuit.

If DTC P1325 is displayed, check No.6 ignition coil with igniter circuit.

If DTCs P1300, P1315 and P1325, are output simultaneously, IGF1 circuit may be open or short.

If DTCs P1305, P1310 and P1320, are output simultaneously, IGF2 circuit may be open or short.

Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
1 Check spark plug and spark (See page DI-58).

A11663
VV1, VV2 and NE Signal Waveforms2 V
/Division
20 msec./Division (Idling)
VV1
NE VV2GND
GND
GND
DI-124
- DIAGNOSTICSENGINE
280 Author
: Date
:
2001 AVALON (RM808U)
DTC P1345 VVT Sensor/Camshaft Position Sensor Cir-
cuit Malfunction (Bank 1)
DTC P1350 VVT Sensor/Camshaft Position Sensor Cir-
cuit Malfunction (Bank 2)
CIRCUIT DESCRIPTION
VVT sensor (VV signal) consists of a magnet, iron core and pickup coil.
The VV signal plate has 3 teeth on its outer circumference and is installed the camshaft timing gear.
When the camshafts rotate, the protrusion on the signal plate and the air gap on the pickup coil change,
causing fluctuations in the magnetic field and generating an electromotive force in the pickup coil.
The actual camshaft angle is detected by the VVT sensor and it provides feedback to the ECM to control
the intake valve timing in response to during condition.
DTC No.DTC Detecting ConditionTrouble Area
No VVT sensor (Camshaft position sensor) signal to ECM
during cranking at 4 sec. or more

Open or short in VVT sensor (camshaft position sensor) cir-
P1345
P1350No VVT sensor (Camshaft position sensor) signal to ECM with
5 sec. or more engine speed 600 rpm or morecuit

VVT sensor (camshaft position sensor)

Camshaft timing gearP1350
While crankshaft rotates twice, VVT sensor (Camshaft position
sensor) signal will be input to ECM 5 times.
Camshaft timing gear

ECM
WIRING DIAGRAM
Refer to DTC P0335 on page DI-67.
INSPECTION PROCEDURE
HINT:

If DTC P1345 is displayed, check left bank VVT sensor (camshaft position sensor).

If DTC P1350 is displayed, check right bank VVT sensor (camshaft position sensor).

Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
1 Check resistance of VVT sensor (See page IG-7).
Reference: INSPECTION USING OSCILLOSCOPE
During idling, check the waveforms between terminals VV1 and
NE+, and VV2 and NE- of the ECM connector.
HINT:

The correct waveforms are as shown.

The waveform frequency is shortened as the engine
speed becomes higher.
NG Replace VVT sensor.
DI6T9-01

A07621A09776
Right Bank OCV
1
2R-B
RECM
OC1+
OC1-
OC2+
OC2- 29
18 Left Bank OCV
R-WR-L 1
2E46
5
E4
E4
E4
- DIAGNOSTICSENGINE
DI-127
283 Author
: Date
:
2001 AVALON (RM808U)
DTC P1349 VVT System Malfunction (Bank 1)
DTC P1354 VVT System Malfunction (Bank 2)
CIRCUIT DESCRIPTION
VVT system controls the intake valve timing to proper timing in response to driving condition.
ECM controls Oil Control Valve (OCV) to make the intake valve timing properly, and, oil pressure controlled
with OCV is supplied to the VVT controller, and then, VVT controller changes relative position between the
camshaft and the crankshaft.
DTC No.DTC Detecting ConditionTrouble Area
P1349
P1354
Condition (a) or (b) continues for after the engine is warmed up
and engine speed at 400 - 4,000 rpm:
(a) Valve timing does not change from of current valve timing
(b) Current valve timing is fixed
Valve timing

OCV

VVT controller assembly

ECM
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P1349 is displayed, check left bank VVT system circuit.

If DTC P1354 is displayed, check right bank VVT system circuit.

Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
DI6TB-01

DI-54
- DIAGNOSTICSENGINE
210 Author
: Date
:
HINT:

When the DTC P0171 or P0174 is recorded, the actual air-fuel ratio is on the lean side. When DTC
P0172 or P0175 is recorded, the actual air-fuel ratio is on the rich side.

If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 is recorded. The MIL
then comes on.

If the total of the short-term fuel trim value and the long-term fuel trim value is within + 35 % (80°C
(176°F) or more), the system is functioning normally.

The A/F sensors (bank 1, 2 sensor 1) output voltage and the short-term fuel trim value can be read
using the OBD II scan tool or hand-held tester.

The ECM controls the voltage of AFR+, AFL+, AFR- and AFL- terminals of ECM to the fixed voltage.
Therefore, it is impossible to confirm the A/F sensor output voltage without OBD II scan tool or hand-
held tester.

OBD II scan tool (excluding hand-held tester) displays the one fifth of the A/F sensors (bank 1, 2 sen-
sor 1) output voltage which is displayed on the hand-held tester.
WIRING DIAGRAM
Refer to DTC P0125 on page DI-43.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for determining
whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean
or rich, etc. at the time of the malfunction.
1 Check air induction system (See page SF-1).
NG Repair or replace.
OK
2 Check injector injection (See page SF-23).
NG Replace injector.
OK