CD player TOYOTA AVALON 2001 Service Repair Manual

BE-136
- BODY ELECTRICALAUDIO SYSTEM
1740 Author
: Date
:
2001 AVALON (RM808U)
3. Europe models:
DIAGNOSIS CODE LIST
TermsMeaning
Physical addressThree-digit code (shown in hexadecimal) which is given to each component com-
prising the AVC-LAN.
Corresponding to the function, individual symbols are specified.
Logical addressTwo-digit code (shown in hexadecimal) which is given to each function comprising
the inner system of the AVC-LAN.
(a) Physical address 190: Radio receiver assembly
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It is stored when 180 sec. has passed after the power supply connector is pulled out after engine
start.
*3: It may be stored when the engine key is turned 1 min. again after engine start.
*4: It may be stored when the engine key is turned again after engine start.
*5: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.
(1) Logical address: 01 (Communication control)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
D6
*1Absence of MasterComponent in which this code is recorded
has been disconnected from system with
ignition in ACC or ON. Or, when this code
was recorded, multi-display assembly was
disconnected.Check harness for power supply system of
multi-display.
Check harness for communication system
of multi-display.
Check harness for power supply system of
radio and player.
Check harness for communication system
of radio and player.
D8
*2No Response to Connection CheckComponent shown by auxiliary code is or
had been disconnected from system after
engine is start.
D9Check harness for power supply system of
component shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
D9
*1Last Mode ErrorComponent operated (sounds and/or
images were provided) before engine stop is
or has been disconnected with ignition
switch in ACC or ON.Check harness for power supply system of
component shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
DANo Response to ON/OFF InstructionNo response is identified when changing
mode (audio and visual mode change).
Detected when sound and picture does not
change by button operation.Check harness for power supply system of
component shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
If error occurs again, replace component
shown by auxiliary code.
DB
*1Mode Status ErrorDual alarm is detected.Check harness for power supply of compo-
nent shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
DC
*3Transmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(Detecting this DTC does not necessarily
mean actual failure.)If same auxiliary code is recorded in order
component, check harness for power supply
and communication system of all compo-
nents shown by code.

- BODY ELECTRICALAUDIO SYSTEM
BE-137
1741 Author
: Date
:
2001 AVALON (RM808U) DD
*4
Master Reset (Momentary Interruption)After engine is started, multi-display assem-
bly was disconnected from system.Check harness for power supply system of
multi-display.
Check harness for communication system
of multi-display.
Check harness for power supply system of
radio and player.
Check harness for communication system
of radio and player.
If this error occurs frequently, replace mul-
ti-display assembly.
DE
*4Slave Reset (Momentary Interruption)After engine is started, slave component
was disconnected from system.Check harness for power supply of compo-
nent shown by auxiliary code.
Check harness for communication system
of component shown by auxiliary code.
DF
*5Master ErrorDue to defective condition of component
with a display, master function is switched to
audio equipment.
Error occurs in communication between
sub-master (audio) and master component.Check harness for power supply of multi-
display assembly.
Check harness for communication system
of multi-display assembly.
Check harness for communication system
between multi-display assembly and sub-
master component.
E0
*1Registration Completion Instruction ErrorºRegistration Completion Instructionº com-
mand from master cannot be received.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
E1
*1Audio processor ON errorWhile source equipment is operating, AMP
output is stopped.Check harness for power supply of multi-
display assembly.
Check harness for communication system
of multi-display assembly.
E2ON/OFF Instruction Parameter ErrorError occurs in ON/OFF controlling com-
mand from multi-display assembly.Replace multi-display assembly.
E3
*1Registration Request TransmissionRegistration Request command is output
from slave component.
Receiving Connection Check Instruction,
Registration Request command is output
from sub-master component.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
(2) Logical address: 61 (Cassette switch)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
40Mechanical of Media ErrorMalfunction due to mechanical failure is
identified.
Or cassette tape is cut or entangled.Inspect cassette tape.
Replace radio and player.
(b) Physical address: 440 Stereo component amplifier
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. again after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.

BE-138
- BODY ELECTRICALAUDIO SYSTEM
1742 Author
: Date
:
2001 AVALON (RM808U)
Logical address: 01 (Communication control)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
D6
*1Absence of MasterComponent in which this code is recorded
has been disconnected from system with
ignition in ACC or ON. Or, when this code
was recorded, multi-display assembly was
disconnected.Check harness for power supply of radio
and player.
Check harness for communication system
of radio and player.
Check harness for power supply of stereo
component amplifier.
Check harness for communication system
of stereo component amplifier.
D4Communication Check ErrorComponent in which this code is recorded is
or was disconnected from system after en-
gine start. Or, when recording this code,
multi-display assembly was disconnected.Check harness for power supply of radio
and player.
Check harness for communication system
of radio and player.
Check harness for power supply of stereo
component amplifier.
Check harness for communication system
of stereo component amplifier.
D1
*2Transmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(Detecting this DTC does not necessarily
mean actual failure.)If same auxiliary code is recorded in order
component, check harness for power supply
and communication system of all compo-
nents shown by code.
(c) Physical address: 240 CD Auto Changer
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.
*2: It may be stored when the engine key is turned 1 min. again after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: It may be stored when the engine key is turned again after engine start.
*5: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.
(1) Logical address: 01 (Communication control)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
DITransmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(This code does not necessarily mean actu-
al failure.)If same auxiliary code is recorded in other
component(s), check harness for power
supply and communication system of com-
ponents shown sub code.
D4
*5Connection check Error
Component in which this code is recorded is
or was disconnected from system after en-
gine start. Or, when recording this code,
multi-display assembly was disconnected.Check harness for power supply of multi-
display.
Check harness for communication system
of multi-display.
Check harness for power supply of CD
auto changer.
Check harness for communication system
of CD auto changer.
(2) Logical address: 63 (CD Auto Changer)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
60CD ErrorError is detected in CD auto changer.Replace CD auto changer
61EJECT ErrorMagazine cannot be ejected.Replace CD auto changer
62No Disc ReadoutDisc cannot be read.Inspect CD

DTCDiagnosis item
Diagnosis contentCountermeasure
and inspected parts
D1
FF
60Radio receiver check.
50Cassette error
Transmitter error
Diagnosis no response
CD error
61
EJECT error
62
63
64
67DISC inside out/flaw
Pickup temperature
detection
Excessive current
detection
Tray insertion/
discharging errorThere is an error in cassette
deck.
Communication with the
equipment that is
communicating has failed
successively.
Result of diagnosis is not
issued from start to finish.
Error codes other than
61-69 are detected.
CD is not ejected.
CD is inserted inside
out or it has a flaw.
High temperature of CD
changer is detected.
Excessive current to
CD changer is detected.
An error occurs in insertion
and discharging operation of
CD changer tray.Radio receiver check.
CD changer check.
CD changer check.
Magazine check.
CD check.
CD changer check.
CD changer check.
Magazine check.Radio receiver check.
Wire harness and
connecter check.
CD
(240)
(360)System
Check
Diagnosis
memory

X

X
X
X
X
X
X
X



 Head
Unit
(190) Parts
Name
D2Periodic
communication
no response
Error in periodic
communication. Wire harness and
connector X

68
D1
D4Elevator error
Periodic communication
errorAn error occurs in
elevator of CD changer
elevator.X

X

 Transmitter error
 Radio receiver check.
 Wire harness check.
CD changer check.
Communication with the
equipment that is
communicating has failed
successively.
Connection confirmation
has not come from the
equipment that is
communicating
- BODY ELECTRICALAUDIO SYSTEM
BE-139
1743 Author
: Date
:
2001 AVALON (RM808U) 63
CD Auto Changer Temp. Too HighReadout cannot be done because tempera-
ture around player's pick-up (reading part)
is too high.With IG switch OFF, leave vehicle in cool
shaded place for a while and re-check.
After deleting the DTC memory, if same
code detected, replace CD auto changer.
64CD Changer Excess CurrentExcess current is applied CD auto changer.Replace CD auto changer
4. Except Europe models:
DIAGNOSIS CODE LIST
If there is ºOº in the column of system check, an error can be detected when the mode is switched to
the system check mode.
If there is ºOº in the column of diagnosis mode, each unit is monitoring whether or not it has failure.
In case of detectng failure, it memorizes DTC.

- BODY ELECTRICALAUDIO SYSTEM
BE-141
1745 Author
: Date
:
2001 AVALON (RM808U)
5. PROBLEM SYSMPTOMS TABLE
NOTICE:
When replacing the internal mechanism (computer part) of the audio system, be careful that no part
of your body or clothing comes in contact with the terminals of the leads from the IC, etc. of the re-
placement part (spare part).
HINT:
This inspection procedure is a simple troubleshooting which should be carried out on the vehicle during sys-
tem operation and was prepared on the assumption of system component troubles (except for the wires and
connectors, etc.).
Always inspect the trouble taking the following items into consideration.
Open or short circuit of the wire harness
Connector or terminal connection fault
ProblemFlow chart No.
RadioRadio not operating when power switch turned to 'ON'.1
Display indicates when power switch turned to 'ON', but no sound (including
'noise') is produced.2
Noise present, but AM - FM not operating.3
Any speaker does not work.4
Any AM or FM does not work.5
Few preset turning bands.5
Reception poor.6
Sound quality poor.7
Preset memory disappears.8
Tape PlayerCassette tape cannot be inserted.9
Cassette tape inserted, but no power.10
Power coming in, but tape player not operating.11
Any speaker does not work.12
Sound quality poor.13
Tape jammed, malfunction with tape speed or auto-reverse.14
Cassette tape will not eject.15
CD Auto ChengerCD magazine cannot be inserted.16
CD magazine inserted, but no power.17
Power coming in, but CD player not operating.18
Sound jumps.19
Sound quality poor (Volume faint).20
Any speaker does not work.21
CD magazine will not be ejected.22
Power AmplifierNo power coming in.23
Power coming in, but power amplifier not operating.24
Any speaker does not work.25
NoiseNoise occurs26
Noise produced by vibration or shock while driving.27
Noise produced when engine starts.28
The term ºAMº includes LW,MW and SW, and the term ºFWº includes UKW.

1 Radio RADIO NOT OPERATING WHEN POWER SWITCH TURNED TO ºONº
+ B wire harness faulty.
GND faulty.
Power amplifier or ACC wire harness faulty.
Power amplifier or +B wire harness faulty.
GND faulty. Is tape player operating normally?
Check if RAD-No.2 fuse is OK?
Is power supplied to ACC terminal of power amplifier?Ye s
NG
No OK No
No
No
No OK
OK
OK Ye s
Ye s
Ye s
Ye sNG
NG
NG Check if RAD-No.1 fuse is OK?
Radio assembly faulty.Replace fuse.
ACC wire harness faulty.
Check if GND (wire harness side) to radio assembly is OK?Radio assembly faulty.
Replace fuse.
Is power supplied to +B terminal of power amplifier?
Is power supplied to ACC terminal of radio assembly?
Is power supplied to +B terminal of radio assembly? Check if GND (wire harness side) of power amplifier
grounded normally? BE-142
- BODY ELECTRICALAUDIO SYSTEM
1746 Author
: Date
:
2001 AVALON (RM808U)

2 RadioDISPLAY INDICATES WHEN POWER SWITCH TURNED TO
ºONº, BUT NO SOUND (INCLUDING ºNOISEº) IS PRODUCED
+ B wire harness faulty.
GND faulty.
Power amplifier faulty.
Speaker wire harness faulty. GND faulty. Is tape player operating normally?
Check if RAD-No.2 fuse is OK?Ye s
NG
No OK No
No
No
No OK
OK
OK Ye s
Ye s
Ye s
Ye sNG
NG
NG Check if RAD-No.1 fuse is OK?
Radio assembly faulty. Recheck system after repair.Replace fuse.
ACC wire harness faulty. Radio assembly faulty.
Replace fuse.
Does continuity exist in speaker wire harness?
Temporarily install another speaker. Functions OK?
Hiss noise from speaker?Ye s
Ye s NoNo
No Ye sPower amplifier faulty.
Power amplifier faulty.
Recheck system after repair. Speaker faulty.
Is power supplied to ACC terminal of power amplifier?
Check if GND (wire harness side) of power amplifier
grounded normally? Is power supplied to +B terminal of power amplifier?
Is power supplied to ACC terminal of radio receiver?
Is power supplied to +B terminal of radio receiver?
Check if GND (wire harness side) of power amplifier
grounded normally?
- BODY ELECTRICALAUDIO SYSTEM
BE-143
1747 Author
: Date
:
2001 AVALON (RM808U)

Speaker wire harness faulty. Is tape player operating normally?
Ye s
No
Radio assembly faulty.
Recheck system after repair. Radio assembly faulty.
Temporarily install another speaker? Functions OK?
Power amplifier faulty. Recheck system after repair.Speaker faulty. 4 Radio ANY SPEAKER DOSE NOT WORK
Is hiss noise produced by non-functioning speaker?
Does continuity exist in speaker wire harness?Ye s
Ye s No
Ye s
NoNo 3 Radio NOISE PRESENT, BUT AM-FM NOT OPERATING
Go to No.25
Radio faulty. If radio side faulty.
BE-144
- BODY ELECTRICALAUDIO SYSTEM
1748 Author
: Date
:
2001 AVALON (RM808U)

5 RadioANY AM OR FM DOES NOR WORK
FEW PRESET TUNING BANDS
Problem with radio wave signals or location?
Are both AM and FM defective?Radio assembly faulty.
Go to No.16
Is tape player operating normally? Radio assembly faulty.
Is power for the antenna being output from the radio assembly?
Hiss noise from speaker? Temporarily install another speaker. Functions OK?
Radio assembly faulty. Recheck system after repair.Speaker faulty.
Power amplifier faulty.
Recheck system after repair. Poor signals, poor location.
No
Ye s
Ye s No
No
NoYe s
Ye s
Ye s
Ye s
No
No
- BODY ELECTRICALAUDIO SYSTEM
BE-145
1749 Author
: Date
:
2001 AVALON (RM808U)

7 Radio SOUND QUALITY POOR
Ye sNo
Ye s
NG
OK Is sound quality always bad?
Is tape player operating normally?Poor signals, poor location.
Radio assembly faulty.
Install properly.
Speaker faulty. Is tape player operating normally?
Is speaker properly installed?
Radio assembly or power amplifier faulty.
Recheck system after repair. Temporarily install another speaker. Functions OK?Is sound quality bad in certain
areas only?
Radio assembly or power
amplifier faulty.
Can cassette tape be inserted in tape player?
Check if RADIO No.1 fuse is OK?Radio assembly faulty.
Replace fuse.
+B wire harness faulty.
GND faulty.
Power amplifier faulty. 8 Radio PRESET MEMORY DISAPPEARSNo
Radio assembly faulty.
No
NoNo NoYe s
Ye s
Ye s
Power amplifier faulty.
Radio assembly faulty.Ye s
Ye sYe s
No
No
No NG
NG
OKOKYe s
Check if GND (wire harness side) of power amplifier
grounded normally? Is power supplied to +B terminal of power amplifier?
Check if GND (wire harness side) of radio assembly
grounded normally? Is power supplied to +B terminal of radio assembly?
- BODY ELECTRICALAUDIO SYSTEM
BE-147
1751 Author
: Date
:
2001 AVALON (RM808U)