fuel cap TOYOTA AVALON 2001 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 953 of 1897
A10140
ECM
VSV
for EVAP
Charcoal Canister
Fuel Tank Fig. 1
(2)
(3) (4) (6)
(8)
(9)(1)
(5)
Fuel Tank Over
Fill Check Valve
(7)Vapor Pressure
Sensor
VSV for
CCVVSV for
Pressure
Switching
Valve
(10)
(11) DI-74
- DIAGNOSTICSENGINE
230 Author: Date:
2001 AVALON (RM808U)
DTC P0440 Evaporative Emission Control System Mal-
function
DTC P0442 Evaporative Emission Control System Leak
Detected (Small Leak)
CIRCUIT DESCRIPTION
The vapor pressure sensor, VSV for canister closed valve (CCV) and VSV for pressure switching valve are
used to detect abnormalities in the evaporative emission control system.
The ECM decides whether there is an abnormality in the evaporative emission control system based on the
vapor pressure sensor signal.
DTC P0440 or P0442 is recorded by the ECM when evaporative emissions leak from the components within
the dotted line in Fig. 1 below, or when the vapor pressure sensor malfunctions.
DTC No.DTC Detecting ConditionTrouble Area
P0440
P0442After cold starting and when generating certain swift pressure
value in fuel tank enabling not to hold that value (2 trip detec-
tion logic)
Hose or tube cracked, hole, damaged or loose seal ((3) in
Fig. 1)
Fuel tank cap incorrectly installed
Fuel tank cap cracked or damaged
Vacuum hose cracked, holed, blocked, damaged or discon-
nected ((1) or (2) in Fig. 1)
Fuel tank cracked, holed or damaged
Charcoal canister cracked, holed or damaged
Open or short in vapor pressure sensor circuit
Vapor pressure sensor
Fuel tank over fill check valve cracked or damaged
ECM
DI6T6-01
Page 954 of 1897
A11666
ECM
Vapor Pressure Sensor
2B6
P-B
VSV for EVAP
B-R
2
15 V
VC
PTNK
E1
E2
EVP1
E01
E01
TBP
3
2
Engine Room J/B
B-W
W-B
P
1
WE5
E82
17
18
7
3
E7
EFI Relay
PL-R
ID1 II215 4
5
E5
ID1 9
6 2G
4 2
53
2
1 EFI
No.1
From
Battery
20
G
VSV for Pressure
Switching ValveCCV
2
110
318
1
VSV for CCV
14
E01 L-R L-R
W WID1
ID1 II2
E5
E8 B-W
2B
2B 2FEFI
No.2
4
EDID1II1 G
B-W B-W
2
P-B
L-OFrom
Terminal
MREL of
ECM
B
B-W
- DIAGNOSTICSENGINE
DI-75
231 Author: Date:
2001 AVALON (RM808U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTC P0441, P0446, P0450 or P0451 is output after DTC P0440 or P0442, first troubleshoot DTC
P0441, P0446, P0450 or P0451. If no malfunction is detected, troubleshoot DTC P0440 or P0442 next.
Ask the customer whether, after the MIL came on, the customer found the fuel tank cap loose and tight-
ened it. Also ask the customer whether the fuel tank cap was loose when refuelling. If the fuel tank cap
was loose, it was the cause of the DTC. If the fuel tank cap was not loose or if the customer was not
sure if it was loose, troubleshoot according to the following procedure.
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
When the ENGINE RUN TIME in the freeze frame data is less than 200 seconds, carefully check the
vapor pressure sensor.
Page 955 of 1897
A10193
DI-76
- DIAGNOSTICSENGINE
232 Author: Date:
2001 AVALON (RM808U)
1 Check whether hose close to fuel tank have been modified, and check whether
there are signs of any accident near fuel tank or charcoal canister.
CHECK:
Check for cracks, deformation and loose connection of the fol-
lowing parts:
Fuel tank
Charcoal canister
Fuel tank filler pipe
Hoses and tubes around fuel tank and charcoal
canister
NG Repair or replace.
OK
2 Check that fuel tank cap is TOYOTA genuine parts.
NG Replace to TOYOTA genuine parts.
OK
3 Check that fuel tank cap is correctly installed.
NG Correctly install fuel tank cap.
OK
4 Check fuel tank cap (See page EC-6).
NG Replace fuel tank cap.
OK
Page 956 of 1897
- DIAGNOSTICSENGINE
DI-77
233 Author: Date:
2001 AVALON (RM808U)
5 Check filler neck for damage.
PREPARATION:
Remove the fuel tank cap.
CHECK:
Visually inspect the filler neck for damage.
NG Replace filler pipe.
OK
6 Check vacuum hoses between vapor pressure sensor and fuel tank, charcoal
canister and VSV for pressure switching valve, and VSV for pressure switching
valve and charcoal canister.
CHECK:
(a) Check that the vacuum hose is connected correctly.
(b) Check the vacuum hose for looseness and disconnection.
(c) Check the vacuum hose for cracks, hole and damage.
NG Repair or replace.
OK
7 Check hose and tube between fuel tank and charcoal canister.
CHECK:
(a) Check for proper connection of the fuel tank and fuel evap pipe (See page EC-6), fuel evap pipe and
fuel tube under the floor, fuel tube under the floor and charcoal canister.
(b) Check the hose and tube for cracks, hole and damage.
NG Repair or replace.
OK
8 Check charcoal canister for cracks, hole and damage (See page EC-6).
NG Replace charcoal canister.
Page 958 of 1897
- DIAGNOSTICSENGINE
DI-79
235 Author: Date:
2001 AVALON (RM808U)
11 Check for open and short in harness and connector between vapor pressure
sensor and ECM (See page IN-30).
NG Repair or replace harness or connector.
OK
Replace vapor pressure sensor.
12 Check fuel tank and fuel tank over fill check valve for cracks and damage.
NG Replace fuel tank or fuel tank over fill check
valve.
OK
It is likely that vehicle user did not properly close fuel tank cap. Please explain to customer how
to properly install fuel tank cap.
Page 960 of 1897
- DIAGNOSTICSENGINE
DI-81
237 Author: Date:
2001 AVALON (RM808U)DTC No.
DTC Detecting ConditionTrouble Area
P0441
Pressure in charcoal canister and fuel tank does not drop dur-
ing purge control (2 trip detection logic)Vacuum hose cracks, holed blocked, damaged or discon-
nected ((1), (2), (3), (4), (5), (6), (7), (8), (9), (10) and (11) in
Fig 1)P0441
During purge cut-off, negative pressure incomming in the char-
coal canister and fuel tank will not stop. (2 trip detection logic)
Fig. 1)
Fuel tank cap incorrectly installed
Fuel tank cap cracked or damaged
Open or short in vaporpressure sensorcircuit
When VSV for pressure switching valve is ON, ECM judges
that there is no continuity between vapor pressure sensor, fuel
tank and charcoal canister (2 trip detection logic)
Open or short in vapor pressure sensor circuit
Vapor pressure sensor
Open or short in VSV circuit for EVAP
VSV for EVAP
O h t i VSV i it f CCV
P0446
When VSV for pressure switching valve is turned OFF, pres-
sure in fuel tank is maintained at atmospheric pressure (2 trip
detection logic)
Open or short in VSV circuit for CCV
VSV for CCV
Open or short in VSV circuit for pressure switching valve
VSV for pressure switching valve
When VSV for CCV is ON, pressure in charcoal canister and
fuel tank is maintained at atmospheric pressure (2 trip detec-
tion logic)
g
Fuel tank cracked, holed or damaged
Charcoal canister cracked, holed or damaged
Fuel tank over fill check valve cracked damaged
ECM
WIRING DIAGRAM
Refer to DTC P0440 or P0442 on page DI-74.
INSPECTION PROCEDURE
HINT:
If DTC P0441, P0446, P0450 or P0451 is output after DTC P0440 or P0442,first troubleshoot DTC
P0441, P0446, P0450 or P0451. If no malfunction is detected, troubleshoot DTC P0440 or P0442 next.
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
When the ENGINE RUN TIME in the freeze frame data is less than 200 seconds, carefully check the
vapor pressure sensor.
TOYOTA hand-held tester:
1 Check whether hose close to fuel tank have been modified, and check whether
there are signs of any accident near fuel tank or charcoal canister (See page
DI-74, step 1).
NG Repair or replace.
OK
2 Check that fuel tank cap is TOYOTA genuine parts (See page DI-74, step 2).
NG Replace to TOYOTA genuine parts.
Page 961 of 1897
DI-82
- DIAGNOSTICSENGINE
238 Author: Date:
2001 AVALON (RM808U)
OK
3 Check that fuel tank cap is correctly installed (See page DI-74, step 3).
NG Correctly install fuel tank cap.
OK
4 Check fuel tank cap (See page EC-6, step 4).
NG Replace fuel tank cap.
OK
5 Check filler neck for damage (See page DI-74, step 5).
NG Replace filler pipe.
OK
6 Check vacuum hoses between vapor pressure sensor and fuel tank, charcoal
canister and VSV for pressure switching valve, and VSV for pressure switching
valve and charcoal canister (See page DI-74, step 6).
NG Repair or connect VSV or sensor connector.
OK
7 Check hose and tube between fuel tank and charcoal canister (See page
DI-74, step 7).
Page 969 of 1897
DI-90
- DIAGNOSTICSENGINE
246 Author: Date:
2001 AVALON (RM808U)
Check and replace charcoal canister (See
page IN-30).
OBD II scan tool (excluding TOYOTA hand-held tester):
1 Check whether hose close to fuel tank have been modified, and check whether
there are signs of any accident near fuel tank or charcoal canister (See page
DI-74, step 1).
NG Repair or replace.
OK
2 Check that fuel tank cap is TOYOTA genuine parts (See page DI-74, step 2).
NG Replace to TOYOTA genuine parts.
OK
3 Check that fuel tank cap is correctly installed (See page DI-74, step 3).
NG Correctly install fuel tank cap.
OK
4 Check fuel tank cap (See page EC-6, step 4).
NG Replace fuel tank cap.
OK
5 Check filler neck for damage (See page DI-74, step 5).
Page 1032 of 1897
DI-16
- DIAGNOSTICSENGINE
172 Author: Date:
P0440
(DI-74)Evaporative Emission Control
System Malfunction
Hose or tube cracked, holed, damaged or insufficient seal
Fuel tank cap incorrectly installed
Fuel tank cap cracked or damaged
Vacuum hose cracked, holed, blocked, damaged or discon-
nected
Fuel tank cracked, holed or damaged
Charcoal canister cracked, holed or damaged
Open or short in vapor pressure sensor circuit
Vapor pressure sensor
Fuel tank over fill check valve cracked or damaged
ECM
P0441
(DI-80)Evaporative Emission Control
System Incorrect Purge Flow
Vacuum hose cracked, holed blocked, damaged or discon-
nected ((1), (2), (3), (4), (5), (6), (7), (8), (9), (10) and (11) in
Fig. 1)
Fuel tank cap incorrectly installed
Fuel tank cap cracked or damaged
Open or short in vapor pressure sensor circuit
Vapor pressure sensor
Open or short in VSV circuit for EVAP
VSV for EVAP
Open or short in VSV circuit for CCV
VSV for CCV
Open or short in VSV circuit for pressure switching valve
VSV for pressure switching valve
Fuel tank cracked, holed or damaged
Charcoal canister cracked, holed or damaged
Fuel tank over fill check valve cracked or damaged
ECM
P0442
(DI-74)Evaporative Emission Control
System Leak Detected (Small
Leak)
Same as DTC No. P0440
P0446
(DI-80)Evaporative Emission Control
System Vent Control MalfunctionSame as DTC No. P0441
P0450
(DI-97)Evaporative Emission Control
System Pressure Sensor Mal-
function
Open or short in vapor pressure sensor circuit
V
P0451
(DI-97)Evaporative Emission Control
System Pressure Sensor Range/
PerformanceVapor pressure sensor
ECM
P0500
(DI-99)Vehicle Speed Sensor Malfunc-
tionCombination meter
Open or short in speed sensor circuit
ECM
P0505
(DI-102)Idle Control System Malfunction
Open or short in IAC valve circuit
IAC valve is stuck or closed
Open or short in A/C signal circuit
Air induction system
ECM
*1: MIL lights up
*2: MIL light up or blinking
Page 1273 of 1897
EC0B4-03
B01082
Gasket
B06544
Vacuum
Gauge
A10838
TOYOTA Hand-Held Tester
DLC3
B06722
Battery EC-6
- EMISSION CONTROLEVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
1100 Author: Date:
2001 AVALON (RM808U)
INSPECTION
1. VISUALLY INSPECT LINES AND CONNECTORS
Visually check for loose connections, sharp bends or damage.
2. VISUALLY INSPECT FUEL TANK FILLER PIPE
Visually check for deformation, cracks or fuel leakage.
3. INSPECT FUEL TANK CAP
Visually check if the cap and/or gasket are deformed or dam-
aged.
If necessary, repair or replace the cap.
4. INSPECT EVAP SYSTEM LINE
(a) Warm up the engine and stop the engine.
Allow the engine to warm up to normal operating tempera-
ture.
(b) Install a vacuum gauge (EVAP control system test equip-
ment vacuum gauge) to the EVAP service port on the
purge line.
(c) TOYOTA Hand-Held Tester:
Forced driving of the VSV for the EVAP.
(1) Connect a TOYOTA hand-held tester to the DLC3.
(2) Start the engine.
(3) Push the TOYOTA hand-held tester main switch
ON.
(4) Use the ACTIVE TEST mode on the TOYOTA
hand-held tester to operate the VSV for the EVAP.
(d) If you have no TOYOTA Hand-Held Tester:
Forced driving of the VSV for the EVAP.
(1) Disconnect the VSV connector for the EVAP.
(2) Connect the positive (+) and negative (-) leads from
the battery to the VSV terminals for the EVAP.
(3) Start the engine.