ignition TOYOTA AVALON HYBRID 2016 XX40 / 4.G Quick Reference Guide
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2016, Model line: AVALON HYBRID, Model: TOYOTA AVALON HYBRID 2016 XX40 / 4.GPages: 52, PDF Size: 1.78 MB
Page 17 of 52

OVERVIEW FEATURES/OPERATIONS TOYOTA SAFETY SENSE SAFETY AND EMERGENCY FEATURES
15
Turn signals
Right turn
Lane change
1
Lane change2
Left turn
1  The right hand signals will flash three times.2  The left hand signals will flash three times.
Power outlets-12V DC
Front console
Type AType B
The “ENGINE START STOP” switch must be in the ACCESSORY or IGNITION ON mode 
for use.
Center console (Accessible from rear seat)
Rear armrest (if equipped) 
Page 26 of 52

24
TOYOTA SAFETY SENSE
 
Pre-Collision System (PCS)
The Pre-Collision System uses a radar sensor and camera sensor to help detect 
vehicles and pedestrians in front of your vehicle. If the system determines that 
the possibility of a frontal collision with a vehicle or pedestrian is high, the system 
warns the driver to take evasive action while the potential brake pressure is 
increased to help the driver avoid collision or reduce the impact to the vehicle and 
it’s occupants. 
Note: PCS is enabled each time the engine switch is turned to Ignition On. The 
system can be disabled/enabled and the warning timing of the system can be 
changed.
Pre-collision warning
When the system determines that the possibility of a frontal collision is high, 
a buzzer will sound and a warning message will be displayed on the Multi-
Information Display (MID) to urge the driver to take evasive action.
Pre-collision brake assist
When the system determines that the possibility of a frontal collision is high, the 
system applies greater braking force in relation to how strongly the brake pedal is 
depressed.
Pre-collision braking
When the system determines that the possibility of a frontal collision is high, the 
system warns the driver. If the system determines that the possibility of a collision 
is extremely high, the brakes are automatically applied to help avoid the collision 
or reduce the collision speed.
 
Changing the pre-collision warning timing
Each time the PCS switch is pressed, 
the response to the warning distance 
changes as follows:
  Far
  Middle
  Near 
Page 27 of 52

25
OVERVIEW FEATURES/OPERATIONS TOYOTA SAFETY SENSE SAFETY AND EMERGENCY FEATURES
 
Disabling the Pre-Collision System (PCS)
To disable the system
Press the PCS switch for 3 seconds or more.
The PCS warning light will turn on and a message will be displayed on the Multi-
Information Display (MID).
To enable the system
Press the PCS switch again.
The system is enabled each time the engine switch is turned to IGNITION ON mode.
Monocular camera sensor
Millimeter wave radar
As part of PCS, this function is also designed to first provide an alert and then 
automatic braking if needed.
Pedestrian Detection Function
The Pre-Collision System also features a pedestrian detection function. Using 
a millimeter wave radar and monocular camera sensor, this advanced sensor 
system can recognize pedestrians in some circumstances. It may provide detection 
capability while driving at low as well as higher speeds. 
Page 36 of 52

34
Push up, or squeeze 
lock release to lower
Seat belts-Shoulder belt anchor
System reset initialization
1. Push and hold “
 SET” button until 
the indicator blinks three times.
2. Wait a few minutes to allow 
initialization to complete. The tire pressure detected by the
tire pressure warning system can
be displayed on the Multi-Information
Display.
Tire Pressure Monitoring (warning)
System
After adjusting tire pressures, or after tires have been rotated or replaced, turn 
the “ENGINE START STOP” switch to IGNITION ON mode and press and hold the 
“
 SET” button until indicator blinks three times. Let the vehicle sit for a few 
minutes to allow initialization to complete.
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation 
specifications. 
If the tire pressure indicator flashes for more than 60 seconds and then remains 
on, take the vehicle to your local Toyota dealer.
NOTE: The warning light may come on due to temperature changes or changes 
in tire pressure from natural air leakage. If the system has not been initialized 
recently, setting the tire pressures to factory specifications should turn off the light.
SAFETY AND EMERGENCY FEATURES