brake rotor TOYOTA AVENSIS 1999 Supplement

SA10A–02
FA1535
SST
F02688
F02721
F02724
– SUSPENSION AND AXLEFRONT DRIVE SHAFT
SA–3
REMOVAL
NOTICE:
The hub bearing could be damaged if it is subjected
to the vehicle weight, such as when moving the ve-
hicle with the drive shaft removed.
Therefore, if it is absolutely necessary to place the ve-
hicle weight on the hub bearing, first support it with
the SST.
SST 09608–16042 (09608–02021, 09608–02041)
w/ ABS:
After disconnecting the drive shaft from the axle hub,
work carefully so as not to damage the ABS speed
sensor rotor serration on the drive shaft.
1. REMOVE FRONT WHEEL
2. DRAIN OUT GEAR OIL
3. w/ ABS:
REMOVE BOLT AND ABS SPEED SENSOR
4. REMOVE DRIVE SHAFT LOCK NUT
(a) Remove the cotter pin and lock cap.
(b) While applying the brakes, remove the nut.
5. DISCONNECT TIE ROD END FROM STEERING
KNUCKLE (See Pub. No. RM599E on page SA–11)
6. DISCONNECT LOWER BALL JOINT FROM LOWER
SUSPENSION ARM (See Pub. No. RM599E on page
SA–11)
7. DISCONNECT DRIVE SHAFT FROM AXLE HUB
(a) Using a plastic hammer, disconnect the drive shaft from
the axle hub.
NOTICE:
Cover the drive shaft boot and ABS speed sensor rotor with
cloth to protect it from being damaged.
(b) Push the front axle hub toward the outside of the vehicle
to separate the drive shaft from the axle hub.
8. REMOVE DRIVE SHAFTS
(a) RH drive shaft:
Remove the 2 bolts and pull out the drive shaft together
with the center bearing bracket.

SA02Z–03
SA–10
– SUSPENSION AND AXLEFRONT DRIVE SHAFT
INSTALLATION
1. LH drive shaft:
INSTALL DRIVE SHAFT TO TRANSAXLE
(a) Install a new snap ring to the inboard joint shaft.
(b) Coat the gear oil to the inboard joint shaft and differential case sliding surface.
(c) Set the snap ring with opening side facing downward.
(d) Using a brass bar and hammer, install the drive shaft.
NOTICE:
Be careful not to damage the dust cover of the drive shaft and oil seal lip of the transaxle.
HINT:
Whether the inboard joint shaft is in contact with the pinion shaft or not can be known from the sound or feel-
ing when driving it in.
(e) Check that there is 2 – 3 mm (0.08 – 0.12 in.) of play in the axial direction.
(f) Check that the drive shaft cannot be removed by hand.
2. RH drive shaft:
INSTALL DRIVE SHAFT TO TRANSAXLE
(a) Coat the gear oil to the inboard joint shaft and differential case sliding surface.
(b) Install the drive shaft with the center bearing bracket.
NOTICE:
Be careful not to damage the dust cover of the drive shaft and oil seal lip of the transaxle.
(c) Install the 2 bolts.
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
3. CONNECT DRIVE SHAFT TO AXLE HUB
NOTICE:
Be careful not to damage the boot and ABS speed sensor rotor.
4. CONNECT LOWER SUSPENSION ARM TO LOWER BALL JOINT
Torque: 127 N·m (1,300 kgf·cm, 94 ft·lbf)
5. CONNECT TIE ROD END TO STEERING KNUCKLE
(a) Connect the tie rod end to the steering knuckle.
(b) Install the nut and a new cotter pin.
If the holes for the cotter pin are not aligned, tighten the nut further up to 60.
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
6. INSTALL DRIVE SHAFT LOCK NUT
(a) While applying brakes, install the nut.
Torque: 216 N·m (2,200 kgf·cm, 159 ft·lbf)
(b) Install the lock cap and a new cotter pin.
If the holes for the cotter pin are not aligned, tighten the nut further up to 60.
7. w/ABS:
INSTALL ABS SPEED SENSOR AND BOLT
Torque: 8.0 N·m (82 kgf·cm, 71 in.·lbf)
8. FILL AND CHECK GEAR OIL (See page MX–4)
9. INSTALL FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
10. CHECK FRONT WHEEL ALIGNMENT (See Pub. No. RM599E on page SA–4)
11. CHECK ABS SPEED SENSOR SIGNAL (See Pub. No. RM599E on page DI–115)

BR11O–01
F08965Non–reusable part N·m (kgf·cm, ft·lbf) : Specified torque
Vacuum Pump

Gasket Vacuum Hose
Casing
Rotor
BladeStraight
Pin
End Cover Check Valve
Union
O–Ring
Vacuum Hose

O–Ring

Gasket

Gasket

O–Ring
Oil Hose
Straight Pin
21 (214, 15)
74 (750, 54)
14 (140, 10)
7.8 (80, 68 in.·lbf)

Snap Ring
Coupling
BR–2
– BRAKEVACUUM PUMP (1CD–FTV)
VACUUM PUMP (1CD–FTV)
COMPONENTS

BR11Q–01
F08966
F08967
F08969
F08970
F08971
BR–4
– BRAKEVACUUM PUMP (1CD–FTV)
DISASSEMBLY
1. PLACE VACUUM PUMP IN VISE
Using soft jaws on the vice, place the vacuum pump in the vice.
NOTICE:
Do not tighten the vise too tightly.
2. REMOVE VACUUM HOSE UNION
Remove the union bolt, union and 2 gaskets.
3. REMOVE CHECK VALVE
Remove the check valve and gasket.
4. REMOVE END COVER
(a) Remove the 3 bolts.
(b) Place the vacuum pump on vise, as shown in the illustra-
tion.
NOTICE:
Do not tighten the vise.
(c) Using a pin punch and hammer, drive out the 2 straight
pins.
(d) Remove the end cover and 2 O–rings.
5. REMOVE ROTOR AND 5 BLADES
NOTICE:
Be careful not to drop the blades.

BR11S–01
F08980
F08981
F08982
New O–Ring
F08970
F08969
– BRAKEVACUUM PUMP (1CD–FTV)
BR–7
REASSEMBLY
1. INSTALL COUPLING
(a) Place the coupling to the rotor shaft.
(b) Install a new snap ring to the rotor shaft.
2. INSTALL ROTOR INTO CASING
Coat the rotor with engine oil, and install it to the rotor shaft.
3. INSTALL 5 BLADES
(a) Coat the 5 blades with engine oil.
(b) Install the 5 blades with the round end facing outward.
HINT:
Be sure that the blades and rotor surfaces are even.
4. INSTALL END COVER
(a) Coat 2 new O–rings with engine oil, and place them to the
casing.
(b) Place the vacuum pump on the vise, as shown in the il-
lustration.
NOTICE:
Do not tighten the vise.
(c) Place the end cover, and temporarily install the 3 bolts.
(d) Using a pin punch and hammer, drive in the 2 straight
pins.
(e) Using soft jaws on the vise, place the vacuum pump in the
vise.
NOTICE:
Do not tighten the vise too tightly.
(f) Tighten the 3 bolts.
Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)