door lock TOYOTA AVENSIS 1999 Supplement

Z14034
Fig.1
Fig.2Power Source
Safing
Sensor
Squibs
Deceleration Sensor
H01581
Outer
H01582
Lock of connector is released
Disconnection is completed
RS–6
– SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
(b) When the vehicle is involved in a frontal collision in the
hatched area (Fig. 1) and the shock is larger than the pre-
determined level, the SRS is activated automatically. A
safing sensor is designed to go on at a smaller decelera-
tion rate than the airbag sensor. As illustrated in Fig. 2,
ignition is caused when current flows to the squib, which
happens when a safing sensor and the deceleration sen-
sor go on simultaneously. When a deceleration force acts
on the sensors, 2 squibs in the driver airbag and front pas-
senger airbag ignite and generate gas. The gas discharg-
ing into the driver airbag and front passenger airbag rap-
idly increases the pressure inside the bags, breaking
open the steering wheel pad and instrument panel door.
Bag inflation then ends, and the bags deflate as the gas
is discharged through discharge holes at the bag’s rear or
side.
7. DISCONNECTION OF SIDE AND CURTAIN SHIELD
AIRBAG SENSOR CONNECTOR
(a) With holding both flank sides of the outer, slide the outer
to the direction shown by an arrow.
(b) Lock of the connectors is released, then disconnect the
connectors.
HINT:
Make sure to hold both flank sides of the outer. If holding the top
and bottom sides, it will obstruct disconnection.

AB0158
Battery
SST
H04668
H04669
Battery
SST
R13455
10 m (33 ft) or more
H04540
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS–13
1. AIRBAG DEPLOYMENT WHEN SCRAPPING VE-
HICLE
HINT:
Have a battery ready as the power source to deploy the airbag.
(a) Check functioning of the SST. (See Pub. No. RM599E on
page RS–17)
SST 09082–00700
(b) Disconnect the side airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Install the SST.
(1) Connect the 2 SST connector to the airbag connec-
tor.
SST 09082–00700, 09082–00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(–) terminal.
(d) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys simultaneously as the LED of SST activa-
tion switch lights up.

AB0158
SSTBattery
H03420
Tires
(5 or More)
R05403
H0342110 m (33 ft) or more SSTBattery
Side Airbag
Assembly
RS–16
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY

Always tie down the side airbag assembly with the
airbag door facing inside.
NOTICE:
The tire will be marked by the airbag deployment, so use
the redundant tire.
(d) Check functioning of the SST.
SST 09082–00700, 09082–00750
(e) Place the tires.
(1) Place at least 2 tires under the tire to which the side
airbag assembly is tied.
(2) Place at least 2 tires over the tire to which the side
airbag assembly is tied. The top tire should have the
wheel installed.
(3) Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harnesses are tight. It is very dan-
gerous when loose wire harnesses results in the tires com-
ing free due to the shock from the airbag deploying.
HINT:
Place the SST connector and wire harness inside tires. Secure
at least 1 m (3 ft) of slack for the wire harness.
(f) Install the SST.
Connect the connector of 2 SST to the side airbag assem-
bly connector.
SST 09082–00700, 09082–00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(g) Deploy the airbag.

H11623
Curtain Shield
Airbag Connector
H11624
Battery
SST
SST
R13455
10 m (33 ft) or more
H11618
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS–27
(c) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(d) Install the SST.
(1) Connect the 2 SST connector to the airbag connec-
tor.
SST 09082–00700, 09082–00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(–) terminal.
(e) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys simultaneously as the LED of SST activa-
tion switch lights up.
(f) Dispose of the curtain shield airbag assembly.
CAUTION:

The curtain shield airbag assembly is very hot when
the airbag is deployed, so leave it alone for at least 30
minutes after deployment.

Use gloves and safety glasses when handling a cur-
tain shield airbag assembly with the deployed airbag.

Do not apply water etc. to a curtain shield airbag as-
sembly with the deployed airbag.

I04818
SPEEDOMETER
TACHOMETER
WATER TEMP.
FUEL
OIL LEVEL
ODO / TRIP
METER
OUTSIDE TEMP.
CLOCK
RHEOSTATLCD
DISPLAY
LCD
DISPLAY S
T
W
FA18
B7
B20 A5
A15
A3
A6
A7
A8
A12
A11
A19
A10
A9
B11
B24
B5
A22
B4
A23
B14
A23
A25
B16
B14
B21
A22
A14VOLTAGE
STABILIZER
B17
B22
B9
B26
A24 Brake Warning
Fuel filter Warning
Discharge Waring
Economy Indicator
Turbo / Glow Plug Indicator
Glow Plug Indicator
ABS Warning
Low Oil Pressure Warning
Check Engine Warning
O / D OFF Indicator
ECT SNOW Indicator
ECT PWR Indicator
Rear Fog Light Indicator
High Beam Indicator
Right Turn Indicator
Left Turn Indicator
Open Door Warning
SRS Warning
Front Fog light Indicator A1
B15
B18A26
B2
A17
B1
B13
B6
B3 B19
BE–4
– BODY ELECTRICALCOMBINATION METER

BO2J3–01
I12491
H03659
H03660
: 4 Clips BO–16
– BODYINSTRUMENT PANEL
REMOVAL
1. REMOVE THESE PARTS:
(a) Remove the front door opening trims.
(b) Remove the front pillar garnishes.
(c) w/ Curtain Shield Airbag:
(1) Remove the 2 bolts.
(2) Pack the airbag with protection cover.
(3) Using a screwdriver, raise the pillar garnish cover.
(4) Remove the bolt, pillar garnish cover and front pillar
garnish.
NOTICE:
Protection rang is from instrument panel to ceiling.
(d) Remove the front door scuff plates.
(e) Remove the cowl side trims.
(f) Remove the rear door opening trims.
(g) Remove the rear door scuff plates.
(h) Remove the center pillar lower covers.
(i) Remove the front seats.
2. REMOVE STEERING WHEEL
(See Pub. No.RM599E on page SR–13)
3. REMOVE LOWER FINISH PANEL
(a) Remove the 2 screws and hood lock control lever.
(b) Remove the 2 screws and lower finish panel.
4. REMOVE THESE PARTS:
(See Pub. No.RM599E on page SR–13)
(a) Remove the column cover.
(b) Remove the combination switch.
(c) Remove the steering column.
5. REMOVE CLUSTER FINISH PANEL
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the cluster finish panel, then
disconnect the connector.
HINT:
Tape the screwdriver tip before use.
6. REMOVE COMBINATION METER

H03662
: 3 Clips
H03661
: 3 Clips
H03660
: 3 Clips
H03659
BO–20
– BODYINSTRUMENT PANEL
8. INSTALL NO.1 UNDER COVER
Install the No.1 under cover.
9. INSTALL NO.1 REGISTER
Install the No.1 register.
10. INSTALL COMBINATION METER
11. INSTALL CLUSTER FINISH PANEL
(a) Install the cluster finish panel, then connect the connec-
tor.
(b) Install the 2 screws.
12. INSTALL THESE PARTS:
(See Pub. No. RM 599E, page SR–13)
(a) Install the steering column.
(b) Install the combination switch.
(c) Install the column cover.
13. INSTALL LOWER FINISH PANEL
(a) Install the lower finish panel with the 2 screws.
(b) Install the hood lock control lever.
14. INSTALL STEERING WHEEL
(See Pub. No. RM 599E, page SR–13)
15. INSTALL THESE PARTS:
(a) Install the front seats.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the center pillar lower covers.
(c) Install the rear door scuff plates.
(d) Install the rear door opening trims.
(e) Install the cowl side trims.
(f) Install the front door scuff plates.