flat tire TOYOTA AVENSIS 1999 Supplement
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1999, Model line: AVENSIS, Model: TOYOTA AVENSIS 1999Pages: 349, PDF Size: 4.88 MB
Page 247 of 349

H11607
AB0158
SSTBattery
H11608
Tires
(5 or More)
R05403
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS–29
(2) Position the inflater of curtain shield airbag inside
the tire with the airbag explosion direction facing in-
side.
Tire size : Must exceed the following dimensions:
Width 185 mm (7.28 in.)
Inner diameter 360 mm (14.17 in.)
CAUTION:
Make sure the wire harness is tight. It is very danger-
ous when a loose wire harness results in the curtain
shield airbag coming free due to the shock from the
airbag exploding.
Always tie down the curtain shield airbag with the ex-
plosion facing inside.
NOTICE:
The tire will be marked by the airbag explosion, so use the
redundant tire.
(c) Check functioning of the SST.
SST 09082–00700, 09082–00750
(d) Place the tires.
(1) Place at least 2 tires under the tire to which the cur-
tain shield airbag is tied.
(2) Place at least 2 tires over the tire to which the curtain
shield airbag is tied. The top tire should have the
wheel installed.
(3) Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harnesses are tight. It is very dan-
gerous when loose wire harnesses results in the tires com-
ing free due to the shock from the airbag exploding.
HINT:
Place the SST connector and wire harness inside tires. Secure
at least 1 m (3 ft) of slack for the wire harness.
Page 267 of 349

BE199–02
I01273
1
2 3
BE–6
– BODY ELECTRICALCOMBINATION METER
INSPECTION
1. INSPECT SPEEDOMETER ON–VEHICLE
Using a speedometer tester, inspect the speedometer for allow-
able indication error and check the operation of the odometer.
HINT:
Tire wear and tire over or under inflation will increase the indica-
tion error.
Europe Models
(mph)(km/h)
Standard indication Allowable range Standard indication Allowable range
20 20 – 24.5 20 20 – 26
40 40 – 46.5 40 40 – 48
60 60 – 68.5 60 60 – 70
80 80 – 90.5 80 80 – 92
100 100 – 112.5 100 100 – 114
120 120 – 136
140 140 – 158
160 160 – 180
If error is excessive, replace the speedometer.
2. INSPECT VEHICLE SPEED SENSOR OPERATION
(a) Connect the positive (+) lead from battery to terminal 1
and negative (–) lead to terminal 2.
(b) Connect the positive (+) lead from tester to terminal 3 and
the negative (–) lead to terminal 2.
(c) Rotate the shaft.
(d) Check that the voltage changes from approx. 0 V to 11 V
or more between terminals 2 and 3.
HINT:
The voltage changes be 4 times every revolution of the speed
sensor shaft.
If operation is not as specified, replace the sensor.
3. INSPECT TACHOMETER/
ON–VEHICLE
(a) Connect a tune–up test tachometer, and start the engine.
NOTICE:
Reversing the connection of the tachometer will dam-
age the transistors and diodes inside.
When removing or installing the tachometer, be care-
ful not to drop or subject it to heavy shocks.