charging TOYOTA AVENSIS 2002 User Guide

02±48
± PREPARATIONHEATER & AIR CONDITIONER
AVENSIS REPAIR MANUAL (RM1018E)
(07117±58080)Quick Disconnect AdapterREFRIGERANT
AIR CONDITIONING RADIATOR
ASSY
W/RECEIVER CONDENSER ASSY
W/PULLEY COMPRESSOR
ASSY(1AZ±FE)
W/PULLEY COMPRESSOR
ASSY(1AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(1CD±FTV)
W/PULLEY COMPRESSOR
ASSY(1ZZ±FE)
W/PULLEY COMPRESSOR
ASSY(2AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(3ZZ±FE)
(07117±58090)Quick Disconnect AdapterREFRIGERANT
AIR CONDITIONING RADIATOR
ASSY
W/RECEIVER CONDENSER ASSY
W/PULLEY COMPRESSOR
ASSY(1AZ±FE)
W/PULLEY COMPRESSOR
ASSY(1AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(1CD±FTV)
W/PULLEY COMPRESSOR
ASSY(1ZZ±FE)
W/PULLEY COMPRESSOR
ASSY(2AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(3ZZ±FE)
(07117±78050)Refrigerant Charging GaugeREFRIGERANT
AIR CONDITIONING RADIATOR
ASSY
W/RECEIVER CONDENSER ASSY
W/PULLEY COMPRESSOR
ASSY(1AZ±FE)
W/PULLEY COMPRESSOR
ASSY(1AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(1CD±FTV)
W/PULLEY COMPRESSOR
ASSY(1ZZ±FE)
W/PULLEY COMPRESSOR
ASSY(2AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(3ZZ±FE)

± PREPARATIONHEATER & AIR CONDITIONER
02±49
AVENSIS REPAIR MANUAL (RM1018E)
(07117±88060)Refrigerant Charging HoseREFRIGERANT
AIR CONDITIONING RADIATOR
ASSY
W/RECEIVER CONDENSER ASSY
W/PULLEY COMPRESSOR
ASSY(1AZ±FE)
W/PULLEY COMPRESSOR
ASSY(1AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(1CD±FTV)
W/PULLEY COMPRESSOR
ASSY(1ZZ±FE)
W/PULLEY COMPRESSOR
ASSY(2AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(3ZZ±FE)
(07117±88070)Refrigerant Charging HoseREFRIGERANT
AIR CONDITIONING RADIATOR
ASSY
W/RECEIVER CONDENSER ASSY
W/PULLEY COMPRESSOR
ASSY(1AZ±FE)
W/PULLEY COMPRESSOR
ASSY(1AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(1CD±FTV)
W/PULLEY COMPRESSOR
ASSY(1ZZ±FE)
W/PULLEY COMPRESSOR
ASSY(2AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(3ZZ±FE)
(07117±88080)Refrigerant Charging HoseREFRIGERANT
AIR CONDITIONING RADIATOR
ASSY
W/RECEIVER CONDENSER ASSY
W/PULLEY COMPRESSOR
ASSY(1AZ±FE)
W/PULLEY COMPRESSOR
ASSY(1AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(1CD±FTV)
W/PULLEY COMPRESSOR
ASSY(1ZZ±FE)
W/PULLEY COMPRESSOR
ASSY(2AZ±FSE)
W/PULLEY COMPRESSOR
ASSY(3ZZ±FE)
07117±48130Vacuum Pump (220 V)W/RECEIVER CONDENSER ASSY
07117±48140Vacuum Pump (240 V)W/RECEIVER CONDENSER ASSY
09870±00015A/C Quick Joint Puller No.1AIR CONDITIONING RADIATOR
ASSY

022J9±01
02±24
± PREPARATIONSTARTING & CHARGING
AVENSIS REPAIR MANUAL (RM1018E)
STARTING & CHARGING
PREPARATION
SST
09249±63010Torque Wrench AdaptorGENERATOR
ASSY(1AZ±FE/1AZ±FSE)
Recomended Tools
09082±00040TOYOTA Electrical TesterSTARTING SYSTEM(1AZ±FE)
STARTING SYSTEM(1AZ±FSE)
STARTING SYSTEM
(1ZZ±FE/3ZZ±FE)
(09083±00150)Test Lead SetSTARTING SYSTEM(1AZ±FE)
STARTING SYSTEM(1AZ±FSE)
STARTING SYSTEM
(1ZZ±FE/3ZZ±FE)
09216±00021Belt Tension GaugeGENERATOR ASSY(1CD±FTV)
Equipment
Slide calipers
Ammeter(A)
Ohmmeter
Radiator cap tester
Torque wrench
Service Wire Harness

031FQ±01
± SERVICE SPECIFICATIONSINTAKE
03±11
AVENSIS REPAIR MANUAL (RM1018E)
INTAKE
SERVICE DATA
1AZ±FSE:
Vacuum switching valve assy No. 1
Resistance at 20
C (68
F)
33 to 39

1CD±FTV:
Turbocharging pressure
Standard pressure
15 to 45 kPa (0.15 to 0.46 kgf/cm2, 2.2 to 6.5 psi)
Turbo pressure sensor
Voltage 3 (VC) ± 1 (E2)
Voltage drop apply vacuum 13.3 kPa (100 mmHg, 3.94 in.Hg)
apply vacuum 26.7 kPa (200 mmHg, 7.87 in.Hg)
apply vacuum 40.0 kPa (300 mmHg, 11.81 in.Hg)
apply vacuum 57.3 kPa (400 mmHg, 15.75 in.Hg)
apply vacuum 66.7 kPa (500 mmHg, 19.96 in.Hg)
Voltage up applied vacuum 19.6 kPa (0.20 kgf/cm2, 2.84 psi)
applied vacuum 39.2 kPa (0.40 kgf/cm2, 5.69psi)
applied vacuum 58.8 kPa (0.60 kgf/cm2, 8.53psi)
applied vacuum 78.5 kPa (0.80 kgf/cm2, 11.4psi)
applied vacuum 98.0 kPa (1.00 kgf/cm2, 14.2psi)
4.5 to 5.5 V
0.1 to 0.3 V
0.3 to 0.5 V
0.5 to 0.7 V
0. 7 to 0.9 V
0. 9 to 1.0 V
0.1 to 0.4 V
0.4 to 0.7 V
0.7 to 1.0 V
1.0 to 1.3 V
1.3 to 1.6 V

031E6±01
03±32
± SERVICE SPECIFICATIONSSTARTING & CHARGING
AVENSIS REPAIR MANUAL (RM1018E)
STARTING & CHARGING
SERVICE DATA
1ZZ±FE/3ZZ±FE:
Starter assy
Rated voltage and output power
Specified current
12 V 1.3 kW
85 A or less at 11.5 V
Starter relay
Specified condition 1 ± 2
3 ± 5
Continuity
No continuity
Battery
Voltage at 20
C (68
F)
12.5 to 12.9 V
Voltage regulator Regulating voltage
Standard amperage12.9 to 14.9 V
10 A or less
1AZ±FE:
Starter assy
Rated voltage and output power
Specified current
12 V 1.3 kW
85 A or less at 11.5 V
Starter relay
Specified condition 1 ± 2
3 ± 5
Continuity
No continuity
Battery
Voltage at 20
C (68
F)
12.5 to 12.9 V
Voltage regulator Regulating voltage
Standard amperage12.9 to 14.9 V
10 A or less
1AZ±FSE:
Starter (1.3 kW type)
Rated voltage and output power
No±load characteristics Current
12 V 1.3 kW
85 A or less at 11.5 V
Starter (1.6 kW type)
Rated voltage and output power
No±load characteristics Current
12 V 1.6 kW
75 A or less at 11.5 V
Starter relay
Specified condition 1 ± 2
3 ± 5
Continuity
No continuity
Battery
Voltage at 20
C (68
F)
12.5 to 12.9 V
Voltage regulator Regulating voltage
Standard amperage12.9 to 14.9 V
10 A or less
1CD±FTV:
Starter assy
Rated voltage and output power
Specified current
12 V 2.0 kW
190 A or less at 11.5 V
Starter relay
Specified condition 1 ± 2
3 ± 5
Continuity
No continuity
Battery
Except maintenance±free battery Standard specific gravity
Voltage at 20
C (68
F)
1.25 to 1.29 at 20
C (68
F)
12.5 to 12.9 V
Voltage regulator Regulating voltage
Standard amperage13.2 to 14.8 V
10 A or less
Glow plugs
Resistance at 20
C (68
F)
Approx. 0.72

Glow plug relay
Specified condition 1 ± 2
3 ± 4
No continuity
Continuity

031E7±03
± SERVICE SPECIFICATIONSSTARTING & CHARGING
03±33
AVENSIS REPAIR MANUAL (RM1018E)
TORQUE SPECIFICATION
1ZZ±FE/3ZZ±FE:
Part TightenedN
mkgf
cmft
lbf
Starter assy x Transaxle housing3737828
Starter wire x Starter assy9.81007
Generator assy x Transverse engine engine mounting bracket2525518
Generator assy x Cylinder block sub±assy5455140
Generator wire x Generator assy9.81007
Lead wire of field coil x Terminal C5.96052 in.
lbf
1AZ±FE/1AZ±FSE:
Part TightenedN
mkgf
cmft
lbf
Wire harness clamp bracket x Starter assy8.48674 in.
lbf
Starter assy x Cylinder block sub±assy3738028
Starter wire x Starter assy9.81007
Battery carrier x Body131319
Battery clamp sub±assy x Body5.05144 in.
lbf
Battery clamp sub±assy x Battery clamp bolt3.63631 in.
lbf
Terminal x Battery5.45548 in.
lbf
Wire harness clamp bracket x Generator assy8.48674 in.
lbf
Generator assy x Cylinder block sub±assy Bolt A
Bolt B52
21530
21438
16
Generator wire x Generator assy9.81007
Lead wire of field coil x Terminal C5.96052 in.
lbf
1CD±FTV:
Part TightenedN
mkgf
cmft
lbf
Starter x Transaxle Bolt
Terminal 3037
9.8377
10027
7.2
Generator assy x Engine M8
M10
Alternator wire
Wire harness31
47
9.8
5.0320
475
100
5123
34
7
44 in.
lbf
Glow plug assy x Cylinder head Glow plug
Nut12.3
2.2125
229
19 in.
lbf
Engine cover No. 1 x Cylinder head cover sub±assy8.08271 in.
lbf
Engine cover No. 1 x Intake manifold8.08271 in.
lbf
Front wheel RH1031,05076

190NV±01
19±14
± STARTING & CHARGINGCHARGING SYSTEM (1AZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
CHARGING SYSTEM (1AZ±FE)
PRECAUTION
1. Check that the battery cables are connected to the correct terminals.
2. Disconnect the battery cables when the battery is given a quick charge.
3. Do not perform tests with a high voltage insulation resistance tester.
4. Never disconnect the battery while the engine is running.
5. Check that the charging cable is tightened on terminal B of the generator and the fuse box.

190NW±01
A81052


A82936
Type A
Type B
BlueWhite
Red Green DarkClear or
light yellow
B00543
± STARTING & CHARGINGCHARGING SYSTEM (1AZ±FE)
19±15
AVENSIS REPAIR MANUAL (RM1018E)
ON±VEHICLE INSPECTION
1. CHECK BATTERY ELECTROLYTE LEVEL
(a) Check the electrolyte quantity of each cell.
(1) If the electrolyte is under the low level, replace the battery (or add distilled water if possible) and
check the charging system.
2. CHECK BATTERY VOLTAGE
(a) If it has not been 20 minutes since you drove the vehicle
or since the engine was stopped, turn the ignition switch
and the electrical system (headlight, blower motor, rear
defogger etc.) to the on position for 60 seconds. This will
remove the surface charge on the battery.
(b) Turn off the ignition switch and the electrical systems.
(c) Measure the battery voltage between the negative (±)
and positive (+) terminals of the battery.
Standard voltage: 12.5 to 12.9 V at 20C (68F)
HINT:
If the voltage is less than specification, charge the battery.
(d) Check the indicator as shown in the illustration.
HINT:
Indicator colorConditionType AType BCondition
GreenBlueOK
DarkWhiteCharging necessary
Clear or light yellowRedReplace
3. CHECK BATTERY TERMINALS, FUSIBLE LINK AND FUSES
(a) Check that the battery terminals are not loosened or corroded.
(b) Check the fusible links, high±current fuses and regular fuses.
4. INSPECT DRIVE BELT
(a) Visually check the belt for excessive wear, frayed cords
etc.
HINT:

If any defect found, replace the drive belt.

Cracks on the rib side of a belt are considered acceptable.
If the belt has chunks missing from the ribs, it should be
replaced.

B00540
A75980
Disconnect Wire
from Terminal B
Generator
Voltmeter BatteryAmmeter 19±16
± STARTING & CHARGINGCHARGING SYSTEM (1AZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
(b) Check that it fits properly in the ribbed grooves.
HINT:
Check with your hand to confirm that the belt has not slipped out
of the groove on the bottom of the pulley.
5. VISUALLY CHECK GENERATOR WIRING
(a) Check that the wiring is in good condition.
6. LISTEN FOR ABNORMAL NOISES FROM GENERATOR
(a) Check that there is no abnormal noise from the generator while the engine is running.
7. INSPECT CHARGE WARNING LIGHT CIRCUIT
(a) Turn the ignition switch ON. Check that the charge warning light comes on.
(b) Start the engine and check that the light goes off.
HINT:
If the light does not operate as specified, troubleshoot the charge warning light circuit.
8. INSPECT CHARGING CIRCUIT WITHOUT LOAD
(a) According to the following procedure, connect an amme-
ter and voltmeter as shown in the illustration.
(1) Disconnect the wire from terminal B of the generator
and connect it to the negative (±) lead of the amme-
ter.
(2) Connect the positive (+) lead of the ammeter to ter-
minal B of the generator
(3) Connect the positive (+) lead of the voltmeter to ter-
minal B of the generator.
(4) Ground the negative (±) lead of the voltmeter.
(b) Check the charging circuit.
(1) Keep the engine speed at 2,000 rpm, check the
reading on the ammeter and voltmeter.
Standard amperage: 10 A or less
Standard voltage: 12.9 to 14.9 V
HINT:

If the voltmeter reading is more than standard voltage, re-
place the voltage regulator.

If the voltmeter reading is less than the standard voltage,
check the voltage regulator and generator as follows:
9. INSPECT CHARGING CIRCUIT WITH LOAD
(a) Keep the engine speed at 2,000 rpm, turn on the high beam headlights and turn the heater blower
switch to the ºHIº position.
(b) Check the reading on the ammeter.
Standard amperage: 30 A or more
HINT:

If the ammeter reading is less than standard amperage, repair the generator.

If the battery is fully charged, the indication will sometimes be less than standard amperage.

190NS±01
± STARTING & CHARGINGCHARGING SYSTEM (1AZ±FSE)
19±17
AVENSIS REPAIR MANUAL (RM1018E)
CHARGING SYSTEM (1AZ±FSE)
PRECAUTION
1. Check that the battery cables are connected to the correct terminals.
2. Disconnect the battery cables when the battery is given a quick charge.
3. Do not perform tests with a high voltage insulation resistance tester.
4. Never disconnect the battery while the engine is running.
5. Check that the charging cable is tightened on terminal B of the generator and the fuse box.