door lock TOYOTA AVENSIS 2002 Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2002, Model line: AVENSIS, Model: TOYOTA AVENSIS 2002Pages: 1690, PDF Size: 32.77 MB
Page 301 of 1690
750N4±01
B66986
Back Door Trim
Panel Assy Upper
Back Door Trim Board Assy Back Door Side
Garnish LHBack Door Garnish Sub±assy
Outside RH
Floor Finish Plate Center Stop Lamp Assy
Back Door Lock Striker Hook
Back Door Side
Garnish RHBack Door Stay Assy RH
Back Door Lock Assy Rear Wiper Motor Assy
Back Door
Stay Assy LH
Back Door Service
Hole Cover
: Specified torqueN´m (kgf´cm, ft´lbf)
19.5 (200, 14)
5.5 (56, 49 in.´lbf)
Hook Rear Wiper Arm and Blade Assy
Rear Wiper
w/ Packing Washer
Wiper Arm Head Cap
Nut5.5 (56, 49 in.´lbf)
5.5 (56, 49 in.´lbf)
Cushion Rubber
Cushion Rubber
Rope Hook Assy
11.5 (120, 8)
22 (264, 19)
7.0 (71, 62 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
7.0 (71, 62 in.´lbf)22 (264, 19)
Female
Stopper RH
Female
Stopper LH
4.9 (49, 43 in.´lbf)Back Door Damper Assy
5.5 (56, 49 in.´lbf)
± ENGINE HOOD/DOORBACK DOOR (LIFTBACK MODELS)
75±37
AVENSIS REPAIR MANUAL (RM1018E)
BACK DOOR (LIFTBACK MODELS)
COMPONENTS
Page 305 of 1690
B66996
B66996
B66991
±
ENGINE HOOD/DOOR BACK DOOR (LIFTBACK MODELS)
75±41
AVENSIS REPAIR MANUAL (RM1018E)
9. REMOVE BACK DOOR LOCK ASSY
(a) Disconnect the connector.
(b) Remove the 3 bolts and door lock.
10.REMOVE BACK DOOR STAY ASSY LH (See page 75±47)
11.REMOVE BACK DOOR STAY ASSY RH (See page 75±47) 12. INSTALL BACK DOOR LOCK ASSY
(a) Install the door lock with the 3 bolts.Torque: 8.0 N m (82 kgf cm, 71 in. lbf)
(b) Connect the door lock connector
13. INSTALL BACK DOOR DAMPER ASSY
(a) Install the damper with the 4 bolts. Torque: 5.5 N m (56 kgf cm, 49 in. lbf)
Page 306 of 1690
750N7±01
B66987
Back Door Trim Panel Assy Upper
Back Door Side Garnish LH Wiper Motor AssyRear Spoiler
Back Door Garnish Sub±assy Outside RH
Back Door Trim Board Assy
Door Pull Handle
Back Door Lock Striker Back Door Side Garnish RH
Door Pull Handle
: Specified torque
N´m (kgf´cm, ft´lbf)
Floor Finish Plate Rear Wiper Arm and Blade Assy
Wiper Arm Head Cap
5.5 (56, 49 in.´lbf)
Rear Wiper w/ Packing
Washer
Back Door
Stay Assy LH
7.0 (71, 62 in.´lbf)
22 (264, 19)
11.5 (120, 8)
Back Door Stay Assy RH
7.0 (71, 62 in.´lbf)
8.0 (82, 71 in.´lbf)
19.5 (200, 14)
Back Door Service Hole Cover
Back Door Lock Assy
4.9 (49, 43 in.´lbf)4.9 (49, 43 in.´lbf)
75±42
± ENGINE HOOD/DOORBACK DOOR (WAGON MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
BACK DOOR (WAGON MODELS)
COMPONENTS
Page 310 of 1690
B66315
B66315
75±46
±
ENGINE HOOD/DOOR BACK DOOR(WAGON MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
9.REMOVE BACK DOOR LOCK ASSY
(a)Disconnect the door lock connector.
(b)Remove the 3 bolts and door lock.
10.BACK DOOR STAY ASSY LH (See page 65±26)
11.BACK DOOR STAY ASSY RH (See page 65±26) 12. INSTALL BACK DOOR LOCK ASSY
(a) Install the door lock with the 3 bolts.Torque: 8.0 N m (82 kgf cm, 71 in. lbf)
(b) Connect the door lock connector.
Page 314 of 1690
B67989
Front Door Outside Handle Frame Sub±assy LHw/ Key:
Front Door Outside Handle Cover LH
Front Door Handle
Assy Outside LH
Front Door Outside Handle Pad Rear Front Door Outside
Handle Pad Front
Hole Plug
Front Door Lock Open Rod
Front Door w/ Motor Lock Assy LH
Door Lock Wire Harness Packing 5.0 (51, 44 in.´lbf)
Front Door Belt Moulding LH
Front Door Hinge
Assy Upper LH
Front Door Check Assy
30 (306, 22)
5.5 (56, 49 in.´lbf)
Front Door Hinge
Assy Lower LH26 (265, 19)
Front Door Weatherstrip LH
Cushion RubberFront Door Lower Frame
Bracket Garnish LH Outer Rear View Mirror Assy LH
Front Door Speaker No. 2
Front Door Service Hole Cover
: Specified torqueN´m (kgf´cm, ft´lbf)
Precoated Part Non±reusable part Clip
26 (265, 19)
Front Door Lower
Frame Seal
Butyl Tape
10 (102, 7)
Front Door Stiffener
Cushion No. 1
Side Trim
Spacer LH
Key Cylinder
w/o Key:
Front Door Outside
Handle Cover LHw/ Speaker
Front Door Lower Frame
Bracket Garnish LH
± ENGINE HOOD/DOORFRONT DOOR
75±5
AVENSIS REPAIR MANUAL (RM1018E)
Page 320 of 1690
B62422
B62423
12
B66968
B61434
B68932Hole Plug
± ENGINE HOOD/DOORFRONT DOOR
75±11
AVENSIS REPAIR MANUAL (RM1018E)
14. REMOVE FRONT DOOR GLASS SUB±ASSY LH
HINT:
Insert a shop rag inside the door panel to prevent the glass from
being scratched.
(a) Move the door glass until the bolts appear in the service
holes.
(b) Remove the 2 bolts holding the door glass to the window
regulator.
(c) Remove the door glass in the direction indicated by the
arrows in the illustration.
NOTICE:
Do not damage the glass.
When the bolts are removed, the glass may fall and
become deformed.
(d) Remove the glass run.
15. REMOVE FRONT DOOR WINDOW REGULATOR
SUB±ASSY LH
(a) Disconnect the window regulator connector.
(b) Remove the 6 bolts and window regulator.
NOTICE:
When the bolts are removed, the window regulator may fall
and become deformed.
HINT:
Remove the window regulator through the service hole.
16. REMOVE FRONT DOOR FRAME SUB±ASSY REAR
LOWER LH
(a) Remove the bolt and frame.
HINT:
Remove the frame through the service hole.
17. REMOVE FRONT DOOR OUTSIDE HANDLE COVER
(a) Remove the hole plug.
(b) Using a torx socket wrench (T30), loosen the screw and
remove the cover with the door lock key cylinder installed.
Page 321 of 1690
B66894
B56613
1
2
B70122
Screw
B57102
B68928
75±12
± ENGINE HOOD/DOORFRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
18. REMOVE FRONT DOOR W/MOTOR LOCK ASSY LH
(a) Disconnect the door lock connector.
(b) Using a torx socket wrench (T30), remove the 3 screws
and door lock.
NOTICE:
When the bolts are removed, the window regulator may fall
and become deformed.
HINT:
Remove the door lock through the service hole.
19. REMOVE FRONT DOOR HANDLE ASSY OUTSIDE LH
(a) Remove the handle pushing and pulling it in the direction
indicated by the arrow mark in the illustration.
(b) Remove the outside handle pads front and rear.
20. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME
SUB±ASSY LH
(a) Using a torx socket wrench (T30), loosen the screw of the
frame.
(b) Using pliers, disengage the clips and remove the frame,
as shown in the illustration.
NOTICE:
Be sure to remove the outside handle together with the
clips, as the clips will be damaged if they remain attached
to the door panel.
HINT:
Remove the frame through the service hole.
21. REMOVE FRONT DOOR CHECK ASSY LH
(a) Remove the 2 nuts, bolt and check.
HINT:
Remove the check through the service hole.
Page 322 of 1690
B68928
Adhesive
B70122
Screw
B64044
1 2
± ENGINE HOOD/DOORFRONT DOOR
75±13
AVENSIS REPAIR MANUAL (RM1018E)
22. REMOVE FRONT DOOR WEATHERSTRIP LH
(a) Using a clip remover, disengage the clips and remove the weatherstrip.
HINT:
If the clips are damaged, replace them with new clips.
23. INSTALL FRONT DOOR CHECK ASSY LH
(a) Apply MP grease to the sliding areas of the check.
(b) Install the check to the door panel with the 2 nuts.
Torque: 5.5 Nm (56 kgfcm, 49 in.lbf)
(c) Apply adhesive to the threads of the bolt.
Adhesive:
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent
(d) Install the door check to the body panel with the bolt.
Torque: 30 Nm (306 kgfcm, 22 in.lbf)
24. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME
SUB±ASSY LH
(a) Install the outside handle link.
(b) Apply MP grease to the sliding areas of the frame.
(c) Using a torx socket wrench (T30), install the frame with
the screw.
Torque: 4.0 Nm (41 kgfcm, 35 in.lbf)
25. INSTALL FRONT DOOR HANDLE ASSY OUTSIDE LH
(a) Install the outside handle pads front and rear.
(b) Install the handle pushing it in the direction of the arrow
mark in the illustration.
NOTICE:
If the release plate is not pulled and held when installing the
handle, the release plate will interfere with the handle and
become damaged.
26. INSTALL FRONT DOOR W/MOTOR LOCK ASSY LH
(a) Apply MP grease to the sliding and rotating areas of the
door lock.
(b) Install a new door lock wire harness packing.
NOTICE:
When reusing a door lock that has been removed, re-
place the packing in the connecting part with a new
one.
Be careful that no grease or dirt does not sticks to the
packing surface in the connecting part.
Reusing removed packing or using damaged packing
will allow water to penetrate through to the connect-
ing part resulting in a door lock malfunction.
Page 323 of 1690
B65961
Rod
B66894
Adhesive
Adhesive
B68932Hole Plug
B62425
B66972
75±14
± ENGINE HOOD/DOORFRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
(c) Insert the control rod into the door lock, and then set it to
the door panel.
NOTICE:
Make sure that the handle link is securely engaged with the
lock.
(d) Apply adhesive to the threads of the 3 screws.
Adhesive:
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent
(e) Using a torx socket wrench (T30), install the door lock with
the 3 screws.
Torque: 5.0 Nm (51 kgfcm, 44 in.lbf)
(f) Connect the door lock connector.
27. INSTALL FRONT DOOR OUTSIDE HANDLE COVER
(a) Using a torx socket wrench (T30), install the cover with the
door lock key cylinder installed with the screw.
Torque: 7.0 Nm (71 kgfcm, 62 in.lbf)
(b) Install the hole plug.
28. INSTALL FRONT DOOR FRAME SUB±ASSY REAR
LOWER LH
(a) Install the frame with the bolt.
Torque: 5.5 Nm (56 kgfcm, 49 in.lbf)
29. I N S TA L L F R O N T D O O R W I N D O W R E G U L ATO R
SUB±ASSY LH
(a) Apply MP grease to the sliding and rotating areas of the
window regulator.
NOTICE:
Do not apply grease to the spring of the window regulator.
Page 327 of 1690
750MT±01
B67533
Hood Sub±assy
Hood Insulator
Engine Room Side Cover RH
Radiator CoverBattery Service Hole Cover
Hood Hinge Assy RH
Hood to Front Fender Seal RH Hood Lock Assy
Front Bumper Assy
Hood to Front Fender Seal LH
Hood Hinge Assy LH x 8
Hood to Front End Panel Seal
8.0 (82, 71 in.´lbf)
13 (133, 10)
13 (133, 10)
: Specified torqueN´m (kgf´cm, ft´lbf)Cushion Rubber
Cushion Rubber
Clip
± ENGINE HOOD/DOORHOOD
75±1
AVENSIS REPAIR MANUAL (RM1018E)
HOOD
COMPONENTS