key TOYOTA AVENSIS 2003 Service Service Manual

71±6
±
INSTRUMENT PANEL/METERCOMBINATION METER
AVENSIS REPAIR MANUAL (RM1018E)
(3)Check that the continuity exists between the terminals.
Float up (switch off): No continuity
(4)Use a syphon, etc., to take fluid out of the reservoir tank.
(5)Check that the continuity exists between the terminals.
Float down (switch on): Continuity
(6)Pour the fluid back in the reservoir tank.
(7)Reconnect the connector.
(8)Check that the buzzer stop after about 4 to 8 seconds.
11.INSPECT KEY REMINDER WARNING BUZZER
(a)Check warning buzzer function. (1)Turn the ignition switch ON and check that the key reminder warning sounds i\
f the ignition keyis insert the key cylinder and front driver side door is opened (See Page 05±1586).
http://vnx.su

730GU±01
73±26
±
THEFT DETERRENT & DOOR LOCK KEY REMINDER WARNING SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
KEY REMINDER WARNING SYSTEM
ON±VEHICLE INSPECTION
1. FUNCTION CHECK
(a) Check that the key reminder warning buzzer sounds. (1) With the driver side door closed, insert the key into the ignition switch lo\
ck cylinder, and then turnthe key to LOCK.
(2) Then, check that the buzzer sounds intermittently when the driver side d\
oor is opened.
(b) Check that the key reminder warning buzzer stops. (1) Check that the buzzer stops sounding when any of the following operation\
s is done while thebuzzer is sounding.

Close the driver side door (front door courtesy lamp switch assy is off).

Turn the ignition switch ON.

Pull out the key from the ignition switch lock cylinder.
http://vnx.su

730GV±01
±
THEFT DETERRENT & DOOR LOCK POWER DOOR LOCK CONTROL SYSTEM
73±1
AVENSIS REPAIR MANUAL (RM1018E)
POWER DOOR LOCK CONTROL SYSTEM
ON±VEHICLE INSPECTION
1. DOOR LOCK FAIL±SAFE
(a) When a malfunction in the door control switch (manual switch, driver's door lock) has been detected,
door lock/unlock operation becomes disabled.
2. CHECK ELECTRICAL DOOR LOCK OPERATION
(a) Check the basic function. (1) Check that all doors lock when the door control switch (for manual operation\
) is turned to LOCKand all doors unlock when turned to UNLOCK.
(2) Check that all doors lock when the driver's door is locked from the outside using the key. Check that all doors unlock when the driver's door is unlocked from the outside using the key.
(b) Check the key lock±in prevention function.
NOTICE:
In order to prevent the key from being locked in, the inspection should be\
made with the driver side
door glass open. (1) Have the key inserted into the ignition key cylinder.
(2) With the driver side door open, check that all doors unlock immediately afte\
r the door lock knob
for the driver side door is turned to LOCK.
(3) With the driver side door open, check that all doors unlock immediately afte\
r the door control switch (for manual operation) is turned to LOCK.
(4) With the driver side door open, turn the driver side door lock knob to LOCK a\
nd hold it for 2 se- conds or more, and then close the driver side door. Then check that all doors unlock.
(c) Check the security function. (1) Close all doors with the driver side door glass open so that the door control\
switch can be oper-ated from outside the vehicle
(2) Pull out the key, open the driver side door and then close and lock the door without usi\
ng the key. Then, check that all doors do not unlock when the door control switch \
(for manual operation)
is turned to UNLOCK from outside the vehicle.
(3) Pull out the key, close and lock the driver side door by key operation. Under this condition, c\
heck
that all doors do not unlock when the door control switch (for manual opera\
tion) is turned to UN-
LOCK from outside the vehicle.
(4) Pull out the key, close the driver side door and lock the door by wireless door lock ope\
ration. Then, check that all doors do not unlock when the door control switch (for manual operation) is
turned to UNLOCK from outside the vehicle.
HINT:
Check that the security function is canceled under the following conditi\
ons.

The ignition switch is turned ON.

The driver side door is unlocked using the key.

The door control switch (for manual operation) is turned to UNLOCK after \
the door control knob is
turned to UNLOCK manually.

The doors are unlocked with wireless operation.
http://vnx.su

73±2
±
THEFT DETERRENT & DOOR LOCK POWER DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
(d) Check the illumination function. (1) Set the room light switch in the DOOR position.
(2) With all doors locked, check that all doors unlock when the driver side door\
lock cylinder is turnedto UNLOCK using the key and that the room right turns on.
(3) Check that the room light turns off in approx. 15 seconds after the doors have not been opened for a while.
3. w/ Double lock:
CHECK DOUBLE LOCKING FUNCTION SYSTEM
(a) Check that the double locking system is set to ON. (1) Open all the windows.
(2) Turn the ignition switch to LOCK and remove the key.
(3) Open and close the driver side door, and make sure that all doors including the back door areclosed securely.
(4) Push the LOCK switch on the wireless transmitter twice within 5 seconds, and check that the hazard warning lights flash once at this time to show that the system is set.
(5) Try to unlock all doors using the inside handle of the vehicle, and check\
that none of the doors
unlock.
NOTICE:

The double locking system cannot be set to ON without using the wireless\
transmitter.

The double locking system operation is not related to the back door.
(b) Check that the double locking system is set to OFF. (1) Push the UNLOCK switch on the wireless transmitter while the double locking system is ON, andcheck that the hazard warning lights flash twice at this time to show th\
at the system is set to OFF.
(2) Check that the doors can be opened both by the inside handle and the outside \
handle.
NOTICE:
If the battery of the wireless transmitter is dead, only the driver side\
door can be opened using the
key. However, the theft deterrent system still remains on. Therefore, be aware that\
the theft alarm
is set off when the door is opened without the use of the wireless trans\
mitter.
http://vnx.su

730G8±01
±
THEFT DETERRENT & DOOR LOCK THEFT DETERRENT SYSTEM
73±31
AVENSIS REPAIR MANUAL (RM1018E)
THEFT DETERRENT SYSTEM
ON±VEHICLE INSPECTION
1. OUTLINE OF THEFT DETERRENT SYSTEM
(a) When the theft deterrent system detects that the vehicle is being tampered with, the sy\
stem sets off
the alarm, causing the horns to sound and the lights to light up or blink in order to alert\
people around
the vehicle to the theft.
(b) The theft deterrent system has an active arming mode; a disarmed state, an \
arming preparation state,
an armed state and an alarm sounding state.
(1) Disarmed state:

The alarm function is not operating.

The theft deterrent system is not operating.
(2) Arming preparation state:

The time until the system goes into the armed state.

The theft deterrent system is not operating.
(3) Armed state:

The theft deterrent system is operating.
HINT:
If the vehicle remains in a condition that sets off the alarm (any door remains open, engine hood remains
open, ignition switch remains directly connected) after the alarm ends,\
the alarm will be set off repeatedly
a maximum of 10 times for every one of the above specified conditions. Alarm time: Approx. 27.5 sec. x 10
(4) Alarm sounding state:When the theft deterrent system detects that the vehicle is being tampered w\
ith while in the
armed state, the system causes the horns to sound and the lights to light up or blink in order t\
o
alert people around the vehicle to the theft.
Refer to table below for alarm method and time:
Hazard Warning LampBlinking (Cycle of flasher relay)
Alarm MethodRoom LampIlluminatingAlarm MethodVehicle HornSounding (Cycle of 0.4 sec.)
Self±power SirenSounding (Cycle of 0.4 sec.)
Alarm TimeApprox. 27.5 sec. (Maximum 10 times)
HINT:
If any of the doors are unlocked with no key in the ignition key cylinde\
r during the armed state, a forced door
lock signal will be output (See step 3).
http://vnx.su

Disarmed state
(No key in ignition key cylinder.)
Continued from next pageContinued on next page
Performing the following will cause the system to go into arming prepara\
tion state.


With all doors and engine hood closed, lock all doors by wireless opera\
tion.
Arming preparation state
Performing any of the following will cause the
system to return to disarmed state.

Unlock any door by wireless operation.

Unlock any door.

Open any door.

Open engine hood.

Insert key into ignition key cylinder.

Reconnect battery.

Turn ignition switch from OFF to ON. With all doors and engine hood closed,
lock all doors. Allow approx. 27.5 sec.
to elapse.
Performing the following will cause the
system to go into armed state.


73±32
±
THEFT DETERRENT & DOOR LOCK THEFT DETERRENT SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
2. ACTIVE ARMING MODE
Active arming mode starts the alarm control right when the doors are loc\
ked.
http://vnx.su

Alarm sounding state
Performing the following will cause the
system to return to disarmed state. When the system detects tam-
pering, horns sound and lights
illuminate or blink in order to
alert people around the vehicle
to the theft.
After approx. 27.5 sec., alarm
stops and system returns to
armed state.
Armed state
Performing any of the following will
cause the system to return to dis-
armed state. Performing any of the follow-
ing will cause the system to
go into alarm sounding state.
Alarm sounding state is canceled. Tampering is detected.
Alarm stops and system
returns to armed state.
Continued from previous page
Continued on previous page

Insert key into ignition key cylin-
der, turn ignition switch ON and
run engine over 550 rpm for 10
to 12 sec.

Unlock all doors by wireless op-
eration. Directly connect ignition
switch without key (or turn
ignition switch ON without
key).


Open engine hood.

Reconnect battery.

Open any door.



Unlock all doors by wireless operation.
±
THEFT DETERRENT & DOOR LOCK THEFT DETERRENT SYSTEM
73±33
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

73±34
±
THEFT DETERRENT & DOOR LOCK THEFT DETERRENT SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
3. FORCED DOOR LOCK CONTROL
(a) The forced door lock control prevents the vehicle from being tampered with. Immediately after a door\
is unlocked (alarm starts), the door is forced to lock by a forced doo\
r lock signal.
(1) Conditions that force the doors to lock:
When no key is in the ignition key cylinder and 0.4 seconds have elapsed aft\
er the previous out-
put of a forced door lock signal, the doors will be forced to lock if any o\
f the following conditions
is present.

The theft deterrent system is in the armed state of active arming mode.

All the doors are locked. Any door is unlocked.

Any door is unlocked.
HINT:
Only Europe:
Forced door lock control does not operate if any door is unlocked by key\
.
4. ALARM MEMORY FUNCTION
(a) If the alarm is set off (tampering is detected) while the theft deterrent system is set, the\
alarm memory function will record it. Whenever you cancel the theft deterrent system, the al\
arm memory function
causes the taillights to light up for 2 seconds in order to inform you t\
hat the alarm has been set off.
(1) Conditions of the alarm memory function that cause the taillights to lig\
ht up:
When the theft deterrent system has entered into the alarm sounding state (\
tampering has been
detected) even once, the taillights will light up for 2 seconds if any of the following conditions is
present.

Switched to the disarmed state from the armed state.
5. SECURITY INDICATOR OUTPUT
(a) The theft warning ECU outputs a signal to light up the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are d\
if-
ferent from the outputs of the theft warning ECU.
Output:
State of Theft Deterrent SystemSecurity IndicatorState of Theft Deterrent SystemOutput Signals from Theft Warning ECUActual Lighting Condition
Disarmed stateOFFOFF (Immobiliser system unset)
BLINKING (Immobiliser system set)
Arming preparation stateONON
Armed stateOFFBLINKING
Alarm sounding stateONON
Blinking cycle:
TimeSecurity Indicator
0.2 sec.ON
1.8 sec.OFF
HINT:
When the immobiliser system is set, the security indicator blinks during the \
disarmed state and the armed
state, due to the output signals from the immobiliser system.
http://vnx.su

730EZ±03
I34799
±
THEFT DETERRENT & DOOR LOCKTRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±19
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION
1.INSPECT TRANSMITTER SUB±ASSY MODULE SET DOOR CONTROL
(a)Inspect operation of the transmitter.
(1)Remove the battery (lithium battery) from the transmitter (See page 73±17).
(2)Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery is not available, connect 2 new
1.5 V batteries in a series, connect the battery positive (+) to the
battery receptacle side terminal and battery negative (±) to the
bottom terminal, then apply 3 V of voltage to the transmitter.
(3)In a location that is approx. 1 m (3.28 ft) away from the driver side ou\
tside door handle in the right direction, point the key plate of the transmitter at the vehicle and che\
ck operation of the transmit-
ter by pressing the transmission switch on the transmitter body.
Standard:
The door lock can be operated via the remote control.
The LED lights up more than once.
HINT:

The minimum operational distance differs, depending on the operator, the way the transmitter is held,
and the location.

Since the transmitter uses faint electric waves, the operational distanc\
e might be shortened if noise
or strong electric wave occurs in the area where the frequency is used.
(4)Install the battery (lithium battery).
(b)Inspect the battery capacity.
HINT:

The capacity of the battery can be determined only when the battery is inst\
alled in the transmitter. For
a lithium battery used in the transmitter, a voltage of more than 2.5 V is shown on the tester until the
energy is completely consumed, while no battery is installed in the transmitte\
r. Therefore, it is neces-
sary to measure the voltage while the battery is installed in the transmitte\
r (a resistance of 1.2 kis
applied to the battery) when checking the amount of energy left in the \
battery.

If the transmitter is faulty, the amount of energy left in the battery might not be checked correctl\
y.
(1)Remove the battery (lithium battery) from the transmitter (See page 73±17).
http://vnx.su

Within 5 sec.
Within 40 sec.
Continued on next page
1.
2.
3.
4.
5.
6.
Insert key into ignition key cylinder, then pull it out.
Close and open driver side door twice.
Close and open driver side door twice.
Insert key into ignition key cylinder and close all doors.
START
Insert key into ignition key cylinder, then pull it out.
Insert key into ignition key cylinder, then pull it out.
Flow Chart of Recognition Code Registration
Within 40 sec.
Within 40 sec. Make sure that the following conditions are met.



No key in ignition key cylinder.

Driver side door is open (Other doors are closed).


Driver side door is unlocked.
73±22
±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su